Metalworking - Page 445

Thread / Thread Starter	Last Post	Replies	Views
micro-vu 10" screen Dan Cullimore	by Grant Erwin	2	313
heating element spliceing question Gunner	by Ted Edwards	33	1,164
Ideas needed for take a part joints Lane	by jtaylor	9	693
FS Morse Taper Drill Drivers MP Toolman	by MP Toolman	0	790
Freezing locks Kamus of Kadizhar	by Jeff Wisnia	67	3,719
Unusual compression spring source needed? Marcel Gonzalez	by Anthony	5	655
Iscar Parting Tool and Tool Block Question... Steve	by TLKALLAM8	6	1,527
Machine shop need near Orlando kdoney	by Richard J Kinch	2	416
cutting glass tubing Ken Sterling	by Randy H.	33	2,148
Induction Furnace Question sme	by J.A. Swann	44	1,747
Cleaning for Oxygen Service Mark	by Randy H.	6	1,497
Buyer beware! Smithy Company. Midas 1720 Dan L.	by LP	24	4,261
PULLEYS OR SHEAVES? Grant Erwin	by Ted Edwards	7	505
SF Bay Area welding supplies Rob Gendreau	by Jim Stewart	5	1,341
DC Generator Ken Sterling	by Ken Sterling	33	1,279
Mill-Drill Stand Mike DeAngelis	by Mike DeAngelis	9	1,402
Elecrical Question KD	by Peter W. Meek	13	707
_Sources_ for carnide chain in the US? Old Nick	by DoN. Nichols	41	1,496
Help me	by Jim Levie	4	348
Home built TIG footpedal: need 14 pin wiring Jack Z	by Keith Marshall	2	1,192
Determining Geologic Sources of Native American Copper Yuri Kuchinsky	by Yuri Kuchinsky	92	4,375
busy building a minibike chopper from scratch, check it out! wallster	by Gunluvver2	31	977
slightly OT - how to make a vacuum from an air supply Norm Dresner	by Wild Bill	19	3,186
Square tubing bender suggestions SteveB	by SteveB	7	996
Mounting motor and gearbox on old mill... jtaylor	by Richard J Kinch	1	456
FS 9" Southbend lathe Wayne	by Wayne	2	550
Gunner is doing fine Sue	by Ken Sterling	23	513
Welcome back Gunner GMasterman	by Kent Frazier	5	451
OT Space rock hits house- For John S. PrecisionMachinisT	by Malcolm Moore	26	862
FS: 16" & 14.5" South Bend Tooling (2&3/8-6tpi) Jesse Hill	by Jesse Hill	0	474
Greater Los Angeles - Shop Space Wanted Dean	by Gunner	1	326
Surface finish [email protected]	by Gunner	14	1,817
Questions on hoist set up Ivan Vegvary	by Bob May	4	338
Building a tracing machine 2 projects ken	by Bob May	3	472
OT Nupla-Flex hammers --The best there is! Harold & Susan Vordos	by Harold & Susan Vordos	8	488
EVERYONE SHOULD SEE THESE! justme	by Scott Moore	3	287
Question from a newbie KMH	by Anthony	6	576
Indexing quill head on mill/drill Robert Scibienski	by Robert Scibienski	11	1,028
i need a schematic for doall dbw 1a welder Asp3211968	by antoine	5	1,038
deep hole question Bill Chernoff	by Dan Caster	14	1,474
ME Index GeoffH	by GeoffH	4	397
how to use a tapping head Aribert	by Aribert	10	1,154
Righty Tighty - But Why? Jeff Wisnia	by shu	57	887
Mill spindle bearing replacement questions Peter Grey	by Harold & Susan Vordos	3	1,136
Need small gearhed electric motor John Ings	by Wild Bill	16	758
What's the deal with HF? SteveB	by Dave Mundt	34	1,018
Quill DRO attachment Philippe Habib	by Philippe Habib	9	295
Help me find this tool.. ant	by Ted Edwards	9	516
DIY Welder from Alternator & Motor George	by steve walker	3	474
VFD won't work on lathe, Why? Jon Elson	by Wayne	20	892
Advice Please: Cutting Brass Strips Darren Harris	by Darren Harris	10	1,188
Require diagram for the Curtis 1203-1 PMDC motor controller GerryO	by GerryO	1	1,194
Hospital bed motors? GTO69RA4	by dalecue	2	354
small engine electronic ignition Ron Thompson	by Larry Jaques	39	3,133
mig welding question Gunner	by Charlie	7	390
ot- The Ted Nugent Show Gunner	by Sue	22	1,246
stuck chuck William R Hopcraft	by Tony	4	523
Wiring 3 phase switch for 2 phase power Dan Miller	by jim rozen	37	1,568
the best way to improve MIG? Shaun	by Charlie	4	364
Nice write up about LEDs Gunner	by z	242	6,792
Hooben tool ID'ed--you're right GTO69RA4	by jim rozen	1	241
OT- Blood pressure monitors? Gunner	by JK	39	878
A9 tool steel Alan Black	by Alan Black	2	394
Cleaning inside a motorcycle crankcase Jim Stewart	by william_b_noble	15	2,683
Finish questions for steel kitchen appliances Peter Grey	by Ted Edwards	5	776
Inner threading turning tool out of HSS...Need for astronomy project Vincent Coppola	by Ted Edwards	16	1,734
Glueing aluminum to other metals Dave Marsh	by Gunner	18	589
Painting exterior metal gate, sand blast, then rust treatment? andy everett	by Bob Edwards	11	2,650
New Metal working / engine building forum Russ Wizinsky	by Russ Wizinsky	0	422
OT? Heavy Metal Stereo Speaker Project Pics JR North	by Harold & Susan Vordos	28	868
Gunner Omniturn question Backlash	by Backlash	2	345
Engraving metals Victorian manual [email protected]	by [email protected]	0	326
Plastic fuel tank repair -Report Al A.	by Al A.	18	1,598
Lathe parting operations Fred Splittgerber	by Fred Splittgerber	10	877
Update to web site and possible gloat. Jim Stewart	by Wayne Cook	23	1,173