Metalworking - Page 86

Thread / Thread Starter	Last Post	Replies	Views
FA Pratt & Whittney 8 inch level looks like a starrett Richard W.	by Richard W.	0	175
Surface Grinder & Tooling f/s [email protected]	by Ron Bean	7	350
Bracelet inspired by a thrust bearing Abrasha	by Abrasha	23	714
WTB 7/8-18 LH tap hoseman	by hoseman	0	314
Bandsaw blade for 6061 Al alloy? What's a good blade size to buy? Eddie	by Harold and Susan Vordos	2	792
Help! Milling conical hole Eat at Sloppy Joes	by Bill Roberto	5	406
usiong pressure washer to remove rust? [email protected]	by Grant Erwin	1	1,889
FA edelstaal tool holder Richard W.	by Richard W.	2	544
bronzes? Peter Fairbrother	by Adam Smith	27	654
Micrometers on eBay... WF	by WF	0	413
Recommended Reading ( 1 2) jon_banquer	by jim rozen	45	1,182
Simple Help Needed - Delta Drill Press Question Joe AutoDrill	by Joe AutoDrill	2	294
Tips on looking for a fabricator [email protected]	by Koz	21	598
Pyrethrin thermal fog & sprayer OT jok18	by Rex B	17	1,062
Help with adjustable reamer Jim B	by [email protected]	4	449
Making a 10 sided dome Joatman71	by Joatman71	6	505
Diesel shutoff valve?? SomeBody	by JohnM	9	489
Winding small springs Tim Shoppa	by Jeff Wisnia	7	339
ISO car museum jackstands Rex B	by carl mciver	23	604
For Glenn Ashmore 1" rods larry g	by larry g	5	313
What is it? LXVIII R.H.	by Rich Grise	35	888
Painting angle iron? Jon Danniken	by lionslair at consolidated dot net	5	1,403
7" electric grinder - reversing rotation? Grant Erwin	by lionslair at consolidated dot net	10	665
Some basic metal lathe questions Grant Erwin	by Harold and Susan Vordos	5	1,283
Way OT - Computer problem... [email protected]	by HotRod	8	395
Alarm system motion detector Tom Gardner	by Gary A. Gorgen	2	409
Source for O6 tooling steel? (no luck so far) [email protected]	by [email protected]	8	341
OT - ICE - A very good idea Just Me	by Dave Hinz	6	500
Ping Ryan in San Fernando- Air Compressor Gunner	by Gunner	0	215
I need a 42 tooth gear for Atlas 618 Bruno	by Wild Bill	9	451
Opinions on Palmgren 803015 Metal/Wood Bandsaw lens	by Peter Wiley	10	941
Homemade arbor press carl mciver	by carl mciver	5	3,130
Phase Converter cycling with compressor to save money. gtslabs	by Chuck Sherwood	16	391
Stainless barbed insert adapter sizing?? Loren Amelang	by Mike Henry	3	546
How does a collet closer work? [email protected]	by [email protected]	18	1,040
OT-Bin priced dvds Time Traveler	by Time Traveler	0	221
Tool for Inserting Roll Pins?? Bob AZ	by Time Traveler	11	1,509
Hanging Large Signs from Metal Studs Steve Koschmann	by lionslair at consolidated dot net	8	3,301
cut tee slots with a shaper shedfull	by tojones(at)cablerocket.com	7	505
Salvaged Steel Fire Door? Bob Chilcoat	by Gunner	15	651
ot. Good, cheap small tractor [email protected]	by JohnM	20	548
Crosslide Crank and Handle on 12" Crafstmas Lathe Terry	by Terry	4	498
Keyboard ? Cliff	by Cliff	5	480
Making a hollow sphere Vic Barkas	by Vic Barkas	20	2,205
duplicating a bronze boat cleat [email protected]	by steamer	10	660
Practical Oxy Acetyline Welding 1938 FA [email protected]	by [email protected]	0	256
95,000 registered, 5000 left Lorn Cummings	by Lorn Cummings	0	259
Biodiesel info Todd Rich	by Treedweller	15	464
OT - American Taliban Cliff	by Bleeding Edge	17	372
looking for letter set - 3/16" - (if on stamp not reversed) Kim	by Dr. Sooz	3	267
What is it? LXX R.H.	by Hank	32	975
Sufficient material for aquarium stand Roy	by Grady	1	283
URGENT, can I use this motor for phase converter? JohnM	by Jerry Martes	2	249
Clausing 1509 cross slide nut assembly Adam Smith	by DoN. Nichols	15	1,212
Differences between CAT40 and NT40 tapers? J Gold	by DoN. Nichols	15	2,544
Realy cool site Mungo Bulge	by DoN. Nichols	2	360
How to adjust steel linked watch band (Wenger Swiss Military waterproof) [email protected]	by zog	33	1,394
computer breakdown Unknown	by JR North	14	645
fa: - Hoke/Phonix regulator dated 1961 - william_b_noble	by william_b_noble	0	252
MasterCAM X Update jon_banquer	by Cliff	8	607
Lerch's Changfa Generator Update James Lerch	by Brian Lawson	6	399
Best way to level gravel turn around [email protected]	by Nick Müller	21	1,132
OT more Environmentalism = slow planet death Cliff	by Cliff	0	274
Just wondering. Sam Clayton	by Jon Danniken	16	527
5th Wheel Hich Position? Nehmo	by Roger & Lorraine Martin	6	585
Sidewalk Sale finds Rick	by Rick	3	405
Zinc Metal Test wsb	by Dave Hinz	5	3,020
I Wish This Book Had Been Available... jon_banquer	by Steve Mackay	24	954
Goonies Never Die!!!!!!! [email protected]	by [email protected]	0	256
OT - Here's a plug... DOC	by Eric R Snow	1	268
Old shaper....minor re-hab question Koz	by Koz	3	394
Seneca Falls lathe value? rigger	by jim rozen	13	847
Did Sherline let down - not! Robert Swinney	by Jordan	8	282
Question re. soapstone in welding Ian W. Douglas	by lionslair at consolidated dot net	19	523
Source for 1/2-8 LH Precision Acme Lead Screw [email protected]	by DoN. Nichols	5	775