Home |
Search |
Today's Posts |
|
Electronics Repair (sci.electronics.repair) Discussion of repairing electronic equipment. Topics include requests for assistance, where to obtain servicing information and parts, techniques for diagnosis and repair, and annecdotes about success, failures and problems. |
Reply |
|
LinkBack | Thread Tools | Display Modes |
#1
Posted to sci.electronics.repair
|
|||
|
|||
Computer runs faster because it is soldered.. haha..
I was reading some flame war and read this.. I am sharing it because I was
qutie entertained. ******************** "So apple computers are hardwired meaning that because everything is directly connected with solder it is going to run faster. this usually makes a computer more expensive." snipped not so funny garblie gook "Source(s): computer science major" ********************* And no I dont want to start a windows vs mac debate.. They both have their places. |
#2
Posted to sci.electronics.repair
|
|||
|
|||
Computer runs faster because it is soldered.. haha..
On Sun, 13 Feb 2011 03:13:35 +0900, "Michael Kennedy"
wrote: I was reading some flame war and read this.. I am sharing it because I was qutie entertained. ******************** "So apple computers are hardwired meaning that because everything is directly connected with solder it is going to run faster. this usually makes a computer more expensive." snipped not so funny garblie gook "Source(s): computer science major" ********************* Cute. It's also wrong in another way. If you cut a board in half you double the cost to manufacture. That includes everything involved in building the board such as procurement, inventory control, handling, packaging, mounting, interconnect, inspection, etc. This is why single board computers are more popular than plug-in conglomerations. The choice solder also makes a minor difference. RoHS Sn/Ag/Cu/Sb solder has a resistivity of 1.21E^-7 ohm.m while Sn/Pb eutectic solder has a resistivity of 1.45E^-7 ohm.m. While a 17% change in conductivity may not seem like much, it makes a hell of difference dealing with ground bounce problems when the 1.4V i7 CPU might draw 65 amps on peaks. Most of the traces are copper, so that had to be beefed up, but the typically crappy soldering also needed thickening. And no I dont want to start a windows vs mac debate.. They both have their places. Aw, you're no fun... I might as well throw in some flame bait. In Dec 2009, I threw together a spreadsheet comparing as near identical offerings from Apple and Dell. See: http://802.11junk.com/jeffl/crud/Mac-vs-PC.xls Except for the 13" MacBook, the price of the Apple products is about twice that of the Dell offerings. Obviously, things have changed since 2009, but since it took me all day to throw that together, I'll wait until I catch a cold or have some time to bring the spreadsheet up to date. Since this is a repair newsgroup, I might mention that many Apple products are impossible to repair. Tearing apart the latest mice and aluminum keyboards will guarantee its destruction. Disassembly of many computers are also difficult and require much prying and swearing. I now carry a putty knife for the Mac Mini, and a roll of mylar tape to reassemble the iBook. The ancient Mac Cube is full of proprietary and nearly unobtainable screws. Opening an iPod, iPhone or iPad is rather tricky, until the tricks are learned. Basically, Apple products are designed to be non-repairable. Gone to find out what stinks in the shop. Probably a dead mouse. -- Jeff Liebermann 150 Felker St #D http://www.LearnByDestroying.com Santa Cruz CA 95060 http://802.11junk.com Skype: JeffLiebermann AE6KS 831-336-2558 |
#3
Posted to sci.electronics.repair
|
|||
|
|||
Computer runs faster because it is soldered.. haha..
On 2/12/2011 3:01 PM Jeff Liebermann spake thus:
Gone to find out what stinks in the shop. Probably a dead mouse. Maybe it's one of those unrepairable Mac mice, moldering in the corner underneath your bench ... -- Comment on quaint Usenet customs, from Usenet: To me, the *plonk...* reminds me of the old man at the public hearing who stands to make his point, then removes his hearing aid as a sign that he is not going to hear any rebuttals. |
#4
Posted to sci.electronics.repair
|
|||
|
|||
Computer runs faster because it is soldered.. haha..
Jeff Liebermann wrote: Gone to find out what stinks in the shop. Probably a dead mouse. Time to switch to a trackball? ;-) -- You can't fix stupid. You can't even put a band-aid on it, because it's Teflon coated. |
#5
Posted to sci.electronics.repair
|
|||
|
|||
Computer runs faster because it is soldered.. haha..
In article m,
David Nebenzahl wrote: On 2/12/2011 3:01 PM Jeff Liebermann spake thus: Gone to find out what stinks in the shop. Probably a dead mouse. Maybe it's one of those unrepairable Mac mice, moldering in the corner underneath your bench ... Youse guys are doing irreparable harm to this group's reputation for linguistic punctiliousness. |
#6
Posted to sci.electronics.repair
|
|||
|
|||
Computer runs faster because it is soldered.. haha..
On Sat, 12 Feb 2011 15:45:49 -0800, David Nebenzahl
wrote: On 2/12/2011 3:01 PM Jeff Liebermann spake thus: Gone to find out what stinks in the shop. Probably a dead mouse. Maybe it's one of those unrepairable Mac mice, moldering in the corner underneath your bench ... Nope. The only mice around here are PC mice. See trophy collection hanging on the closet door in the background. Unlike Apple mice, PC mice don't stink. http://www.LearnByDestroying.com/panorama/jeffl.htm (Wait for the photo to load. Move mouse around photo). It's definitely a dead mouse (Mus musculus). I think I found the general area, but haven't found the dead mouse yet. Dinner tastes like dead mouse. Retch. -- Jeff Liebermann 150 Felker St #D http://www.LearnByDestroying.com Santa Cruz CA 95060 http://802.11junk.com Skype: JeffLiebermann AE6KS 831-336-2558 |
#7
Posted to sci.electronics.repair
|
|||
|
|||
Computer runs faster because it is soldered.. haha..
"Michael Kennedy" wrote in message ... I was reading some flame war and read this.. I am sharing it because I was qutie entertained. ******************** "So apple computers are hardwired meaning that because everything is directly connected with solder it is going to run faster. this usually makes a computer more expensive." snipped not so funny garblie gook "Source(s): computer science major" ********************* And no I dont want to start a windows vs mac debate.. They both have their places. Well I didnt say where their places were. The PC being on my desk.. The Mac proping the door open. |
#8
Posted to sci.electronics.repair
|
|||
|
|||
Computer runs faster because it is soldered.. haha..
On Sun, 13 Feb 2011 03:13:35 +0900, "Michael Kennedy"
wrote: I was reading some flame war and read this.. I am sharing it because I was qutie entertained. ******************** "So apple computers are hardwired meaning that because everything is directly connected with solder it is going to run faster. this usually makes a computer more expensive." snipped not so funny garblie gook "Source(s): computer science major" ********************* And no I dont want to start a windows vs mac debate.. They both have their places. Hardly noticeable, but maybe what he means is that by designing more inclusive circuit boards and thus reducing the need for cabling you do gain some advantage. |
#9
Posted to sci.electronics.repair
|
|||
|
|||
Computer runs faster because it is soldered.. haha..
|
#10
Posted to sci.electronics.repair
|
|||
|
|||
Computer runs faster because it is soldered.. haha..
"Jeff Liebermann" wrote in message ... On Sun, 13 Feb 2011 03:13:35 +0900, "Michael Kennedy" wrote: I was reading some flame war and read this.. I am sharing it because I was qutie entertained. ******************** "So apple computers are hardwired meaning that because everything is directly connected with solder it is going to run faster. this usually makes a computer more expensive." snipped not so funny garblie gook "Source(s): computer science major" ********************* Cute. It's also wrong in another way. If you cut a board in half you double the cost to manufacture. That includes everything involved in building the board such as procurement, inventory control, handling, packaging, mounting, interconnect, inspection, etc. This is why single board computers are more popular than plug-in conglomerations. The choice solder also makes a minor difference. RoHS Sn/Ag/Cu/Sb solder has a resistivity of 1.21E^-7 ohm.m while Sn/Pb eutectic solder has a resistivity of 1.45E^-7 ohm.m. While a 17% change in conductivity may not seem like much, it makes a hell of difference dealing with ground bounce problems when the 1.4V i7 CPU might draw 65 amps on peaks. Most of the traces are copper, so that had to be beefed up, but the typically crappy soldering also needed thickening. And no I dont want to start a windows vs mac debate.. They both have their places. Aw, you're no fun... I might as well throw in some flame bait. In Dec 2009, I threw together a spreadsheet comparing as near identical offerings from Apple and Dell. See: http://802.11junk.com/jeffl/crud/Mac-vs-PC.xls Except for the 13" MacBook, the price of the Apple products is about twice that of the Dell offerings. Obviously, things have changed since 2009, but since it took me all day to throw that together, I'll wait until I catch a cold or have some time to bring the spreadsheet up to date. Since this is a repair newsgroup, I might mention that many Apple products are impossible to repair. Tearing apart the latest mice and aluminum keyboards will guarantee its destruction. Disassembly of many computers are also difficult and require much prying and swearing. I now carry a putty knife for the Mac Mini, and a roll of mylar tape to reassemble the iBook. The ancient Mac Cube is full of proprietary and nearly unobtainable screws. Opening an iPod, iPhone or iPad is rather tricky, until the tricks are learned. Basically, Apple products are designed to be non-repairable. Gone to find out what stinks in the shop. Probably a dead mouse. -- Jeff Liebermann I don't know about Apple computers, because I don't work on them, but I have to say that I find iPods very easy to get into, and all of the major parts are available from multiple sources at what I think are remarkably sensible prices. Just last week, I bought a replacement LCD assembly for a Classic, and it was £10.20 (say $15) including tax and delivery. I got it from my usual supplier here in the UK, and it looked as though it was a factory-original part. Arfa |
#11
Posted to sci.electronics.repair
|
|||
|
|||
Computer runs faster because it is soldered.. haha..
I don't know about Apple computers, because I don't work
on them, but I have to say that I find iPods very easy to get into, and all of the major parts are available from multiple sources at what I think are remarkably sensible prices. Just last week, I bought a replacement LCD assembly for a Classic, and it was £10.20 (say $15) including tax and delivery. I got it from my usual supplier here in the UK, and it looked as though it was a factory-original part. Your good fortune might simply be that there are so many iPods around that 3rd parties find it profitable to manufacture replacements. The fact that you /did not/ purchase an Apple part -- for whatever reason -- doesn't say much good about Apple. I might also dump on Palm. After seven years, I had to replace the lithium-ion battery in my Tungsten T3. Palm has illegally abandoned this and other PDAs, so I had to go elsewhere. Prices were all over the place, as high as $30. (You used to be able to get the battery and its installation for $50 to $60, but no one seems to be doing it any more.) I settled on an HQRP ("high-quality, reasonable price") battery for less than $7, shipping included. It was surprisingly easy to replace (I expected tsuris), and appears to be better (or at least have higher capacity) than the original. Time will tell. |
#12
Posted to sci.electronics.repair
|
|||
|
|||
Computer runs faster because it is soldered.. haha..
On Sun, 13 Feb 2011 16:20:16 -0000, "Arfa Daily"
wrote: I don't know about Apple computers, because I don't work on them, but I have to say that I find iPods very easy to get into, and all of the major parts are available from multiple sources at what I think are remarkably sensible prices. In order to get into a iPhone 3G, you remove 2 small screws, place a suction cup on the glass front, and pull. The battery is soldered in place. Furthur disassembly involves removing glued components (including the battery). It's not impossible, but it's certainly not easy. The previous iPhone 2G required using a plastic "spudger" to pry the off the front. Various teardown instructions: http://www.ifixit.com/Browse/iPhone http://www.ifixit.com/Browse/iPod However, for real entertainment value, try replacing a broken power connector on an old iBook G3. I have one of these and was not thrilled with the approx 50 step procedure. http://www.ifixit.com/Device/iBook_G3_12%22 We can debate whether such inconvenient disassembly is justified by the allegedly improved cosmetics. My position is that it's not, as demonstrated by other cell phones and PC laptops, most of which have user accessible batteries. Just last week, I bought a replacement LCD assembly for a Classic, and it was £10.20 (say $15) including tax and delivery. I got it from my usual supplier here in the UK, and it looked as though it was a factory-original part. Good price. It probably came directly from China from the same factory that supplies the displays to Apple. I get quite a few parts that way through Hong Kong. However, there are some parts which are simply unobtainable new and/or at reasonable prices. Cosmetic parts, custom chips, and wear parts (i.e. power jacks, controls, keyboards, touchpads, hinges, rubber feet, etc) tend to be difficult to find. Most of these I buy from eBay vendors that cannibalize machines and sell the parts. Without used parts, many of the repairs that I'm doing would be either uneconomical or impossible. I could not build the business on purchasing new parts from the original manufacturer. -- Jeff Liebermann 150 Felker St #D http://www.LearnByDestroying.com Santa Cruz CA 95060 http://802.11junk.com Skype: JeffLiebermann AE6KS 831-336-2558 |
#13
Posted to sci.electronics.repair
|
|||
|
|||
Computer runs faster because it is soldered.. haha..
However, there are some parts which are simply
unobtainable new and/or at reasonable prices. The American law used to be "three years" for cosmetic and trim parts. I used to buy trim parts for my favorite electronic "toys" to make sure I had them. |
#14
Posted to sci.electronics.repair
|
|||
|
|||
Computer runs faster because it is soldered.. haha..
Just last week, I bought a replacement LCD assembly for a Classic, and it was £10.20 (say $15) including tax and delivery. I got it from my usual supplier here in the UK, and it looked as though it was a factory-original part. Good price. It probably came directly from China from the same factory that supplies the displays to Apple. I get quite a few parts that way through Hong Kong. However, there are some parts which are simply unobtainable new and/or at reasonable prices. Cosmetic parts, custom chips, and wear parts (i.e. power jacks, controls, keyboards, touchpads, hinges, rubber feet, etc) tend to be difficult to find. Most of these I buy from eBay vendors that cannibalize machines and sell the parts. Without used parts, many of the repairs that I'm doing would be either uneconomical or impossible. I could not build the business on purchasing new parts from the original manufacturer. -- Jeff Liebermann The company I use is http://www.parts4ipods.com Not much use to you as a leftpondian, but as you can see, they do a lot of Apple parts, including some cosmetics and touch screens. Arfa |
#15
Posted to sci.electronics.repair
|
|||
|
|||
30 GB Video Ipod (was: Computer runs faster because it issoldered.. haha..
On Mon, 14 Feb 2011 01:44:27 +0000, Arfa Daily wrote:
Just last week, I bought a replacement LCD assembly for a Classic, and it was £10.20 (say $15) including tax and delivery. I got it from my usual supplier here in the UK, and it looked as though it was a factory-original part. Good price. It probably came directly from China from the same factory that supplies the displays to Apple. I get quite a few parts that way through Hong Kong. However, there are some parts which are simply unobtainable new and/or at reasonable prices. Cosmetic parts, custom chips, and wear parts (i.e. power jacks, controls, keyboards, touchpads, hinges, rubber feet, etc) tend to be difficult to find. Most of these I buy from eBay vendors that cannibalize machines and sell the parts. Without used parts, many of the repairs that I'm doing would be either uneconomical or impossible. I could not build the business on purchasing new parts from the original manufacturer. -- Jeff Liebermann The company I use is http://www.parts4ipods.com Not much use to you as a leftpondian, but as you can see, they do a lot of Apple parts, including some cosmetics and touch screens. Arfa Hey how do I get my 30 GB Video Ipod apart? It has a .5mm streak going from right to left in the middle of the screen but stops just short of the left side. But it is in the backlighting because the streak does not appear in bright light. So it doesn't seem to be the LCD just the lighting. Does this sound right? I don't want to mess with trying to pry it apart and bend it all up but I would like to see if there is something that can be done first without buying a replacement panel. -- Live Fast, Die Young and Leave a Pretty Corpse |
#16
Posted to sci.electronics.repair
|
|||
|
|||
30 GB Video Ipod (was: Computer runs faster because it is soldered.. haha..
On Mon, 14 Feb 2011 18:29:17 +0000 (UTC), Meat Plow
wrote: Hey how do I get my 30 GB Video Ipod apart? http://www.ifixit.com/Browse/iPod I'm not sure which model you have. How to identify your model: http://www.ifixit.com/info/ID-your-iPod It has a .5mm streak going from right to left in the middle of the screen but stops just short of the left side. But it is in the backlighting because the streak does not appear in bright light. So it doesn't seem to be the LCD just the lighting. Does this sound right? No. Backlighting failures usually affect the entire screen, or large areas of the screen, not single horizontal lines. That's the LCD. It's too difficult to see the line with a reflected light. My guess is either a blown LCD display, or a bad connection. It might also be mechanical damage (broken glass) of some sort as I've never seen a line go only partially across the display. don't want to mess with trying to pry it apart and bend it all up but I would like to see if there is something that can be done first without buying a replacement panel. Burnt offerings, human sacrifice, secret incantations, and exhortations to various deities has worked for the last few thousand years. Threats of violence has ocassionally convinved various devices to cooperate and repair themselves. I don't recall if the ISO has standardized any of these methods yet, so some experimentation on your part might be needed. If you do succeed by any of these methods, I would be very interested. -- Jeff Liebermann 150 Felker St #D http://www.LearnByDestroying.com Santa Cruz CA 95060 http://802.11junk.com Skype: JeffLiebermann AE6KS 831-336-2558 |
#17
Posted to sci.electronics.repair
|
|||
|
|||
30 GB Video Ipod (was: Computer runs faster because it is soldered.. haha..
"Meat Plow" wrote in message news On Mon, 14 Feb 2011 01:44:27 +0000, Arfa Daily wrote: Just last week, I bought a replacement LCD assembly for a Classic, and it was £10.20 (say $15) including tax and delivery. I got it from my usual supplier here in the UK, and it looked as though it was a factory-original part. Good price. It probably came directly from China from the same factory that supplies the displays to Apple. I get quite a few parts that way through Hong Kong. However, there are some parts which are simply unobtainable new and/or at reasonable prices. Cosmetic parts, custom chips, and wear parts (i.e. power jacks, controls, keyboards, touchpads, hinges, rubber feet, etc) tend to be difficult to find. Most of these I buy from eBay vendors that cannibalize machines and sell the parts. Without used parts, many of the repairs that I'm doing would be either uneconomical or impossible. I could not build the business on purchasing new parts from the original manufacturer. -- Jeff Liebermann The company I use is http://www.parts4ipods.com Not much use to you as a leftpondian, but as you can see, they do a lot of Apple parts, including some cosmetics and touch screens. Arfa Hey how do I get my 30 GB Video Ipod apart? It has a .5mm streak going from right to left in the middle of the screen but stops just short of the left side. But it is in the backlighting because the streak does not appear in bright light. So it doesn't seem to be the LCD just the lighting. Does this sound right? I don't want to mess with trying to pry it apart and bend it all up but I would like to see if there is something that can be done first without buying a replacement panel. -- Live Fast, Die Young and Leave a Pretty Corpse I agree with Jeff. The problem is most likely the display itself or a connection to it. They come apart quite easily, once you have got one side started. there are lots of videos on You Tube. The English on this one is crap, but the actual video shows it all quite well, except that they don't show any screws down the sides once you have the case off. There have been tiny screws in all the ones I've seen, but they are obvious. http://www.youtube.com/watch?v=UYE9V...eature=related Trickiest bit I've found is when you come to put it back together, and you have to get the centre button in the control ring to stay correctly in place, as you try to get the ring to locate in the case front. Not ultimately hard exactly, just fiddly, and a bit frustrating the first ten times that it falls back out ... :-) Arfa |
#18
Posted to sci.electronics.repair
|
|||
|
|||
30 GB Video Ipod (was: Computer runs faster because it issoldered.. haha..
On Mon, 14 Feb 2011 12:02:36 -0800, Jeff Liebermann wrote:
On Mon, 14 Feb 2011 18:29:17 +0000 (UTC), Meat Plow wrote: Hey how do I get my 30 GB Video Ipod apart? http://www.ifixit.com/Browse/iPod I'm not sure which model you have. How to identify your model: http://www.ifixit.com/info/ID-your-iPod It has a .5mm streak going from right to left in the middle of the screen but stops just short of the left side. But it is in the backlighting because the streak does not appear in bright light. So it doesn't seem to be the LCD just the lighting. Does this sound right? No. Backlighting failures usually affect the entire screen, or large areas of the screen, not single horizontal lines. That's the LCD. It's too difficult to see the line with a reflected light. My guess is either a blown LCD display, or a bad connection. It might also be mechanical damage (broken glass) of some sort as I've never seen a line go only partially across the display. Sorry, the streak is not there when viewing by reflected light. Only with back light. And the glass is not broken nor has it been dropped or bumped or abused. don't want to mess with trying to pry it apart and bend it all up but I would like to see if there is something that can be done first without buying a replacement panel. Burnt offerings, human sacrifice, secret incantations, and exhortations to various deities has worked for the last few thousand years. Threats of violence has ocassionally convinved various devices to cooperate and repair themselves. I don't recall if the ISO has standardized any of these methods yet, so some experimentation on your part might be needed. If you do succeed by any of these methods, I would be very interested. Well I'm on my own. -- Live Fast, Die Young and Leave a Pretty Corpse |
#19
Posted to sci.electronics.repair
|
|||
|
|||
30 GB Video Ipod (was: Computer runs faster because it issoldered.. haha..
On Tue, 15 Feb 2011 02:17:39 +0000, Arfa Daily wrote:
"Meat Plow" wrote in message news On Mon, 14 Feb 2011 01:44:27 +0000, Arfa Daily wrote: Just last week, I bought a replacement LCD assembly for a Classic, and it was £10.20 (say $15) including tax and delivery. I got it from my usual supplier here in the UK, and it looked as though it was a factory-original part. Good price. It probably came directly from China from the same factory that supplies the displays to Apple. I get quite a few parts that way through Hong Kong. However, there are some parts which are simply unobtainable new and/or at reasonable prices. Cosmetic parts, custom chips, and wear parts (i.e. power jacks, controls, keyboards, touchpads, hinges, rubber feet, etc) tend to be difficult to find. Most of these I buy from eBay vendors that cannibalize machines and sell the parts. Without used parts, many of the repairs that I'm doing would be either uneconomical or impossible. I could not build the business on purchasing new parts from the original manufacturer. -- Jeff Liebermann The company I use is http://www.parts4ipods.com Not much use to you as a leftpondian, but as you can see, they do a lot of Apple parts, including some cosmetics and touch screens. Arfa Hey how do I get my 30 GB Video Ipod apart? It has a .5mm streak going from right to left in the middle of the screen but stops just short of the left side. But it is in the backlighting because the streak does not appear in bright light. So it doesn't seem to be the LCD just the lighting. Does this sound right? I don't want to mess with trying to pry it apart and bend it all up but I would like to see if there is something that can be done first without buying a replacement panel. -- Live Fast, Die Young and Leave a Pretty Corpse I agree with Jeff. The problem is most likely the display itself or a connection to it. They come apart quite easily, once you have got one side started. there are lots of videos on You Tube. The English on this one is crap, but the actual video shows it all quite well, except that they don't show any screws down the sides once you have the case off. There have been tiny screws in all the ones I've seen, but they are obvious. http://www.youtube.com/watch?v=UYE9V...eature=related Trickiest bit I've found is when you come to put it back together, and you have to get the centre button in the control ring to stay correctly in place, as you try to get the ring to locate in the case front. Not ultimately hard exactly, just fiddly, and a bit frustrating the first ten times that it falls back out ... :-) Arfa How is it backlit? is it ccfl ? I don't understand when viewed in bright light after the backlight turns off the streak goes away. I can take a pic of it and put it on photobucket: This is with backlight: http://i273.photobucket.com/albums/jj220/meatplow1/Electronics/cimg0047.jpg This is with reflected light only: http://i273.photobucket.com/albums/jj220/meatplow1/Electronics/cimg0046.jpg As you can easily see the reflected light picture shows no anomaly on the screen. It's not just a case of the anomaly being too hard to see with reflected light. -- Live Fast, Die Young and Leave a Pretty Corpse |
#20
Posted to sci.electronics.repair
|
|||
|
|||
30 GB Video Ipod (was: Computer runs faster because it is soldered.. haha..
Arfa How is it backlit? is it ccfl ? I don't understand when viewed in bright light after the backlight turns off the streak goes away. I can take a pic of it and put it on photobucket: This is with backlight: http://i273.photobucket.com/albums/jj220/meatplow1/Electronics/cimg0047.jpg This is with reflected light only: http://i273.photobucket.com/albums/jj220/meatplow1/Electronics/cimg0046.jpg As you can easily see the reflected light picture shows no anomaly on the screen. It's not just a case of the anomaly being too hard to see with reflected light. Hmmm. As you say, the display error does not appear to be there in the second picture, and I'm not sure just what to make of that. As to how the things are backlit, to be honest, I'm not sure. I don't think that it's a ccfl, so possibly LED, but I don't recall the display assembly being thick enough to accommodate sufficiently powerful LEDs. Unless someone else knows, I'll see if I can dig the one I replaced a couple of weeks ago, back out of the workshop bin (un-emptied, and overflowing, as always !!) and see if I can see what lights it Arfa |
#21
Posted to sci.electronics.repair
|
|||
|
|||
30 GB Video Ipod
On Wed, 16 Feb 2011 01:55:09 +0000, Arfa Daily wrote:
Arfa How is it backlit? is it ccfl ? I don't understand when viewed in bright light after the backlight turns off the streak goes away. I can take a pic of it and put it on photobucket: This is with backlight: http://i273.photobucket.com/albums/j...1/Electronics/ cimg0047.jpg This is with reflected light only: http://i273.photobucket.com/albums/j...1/Electronics/ cimg0046.jpg As you can easily see the reflected light picture shows no anomaly on the screen. It's not just a case of the anomaly being too hard to see with reflected light. Hmmm. As you say, the display error does not appear to be there in the second picture, and I'm not sure just what to make of that. As to how the things are backlit, to be honest, I'm not sure. I don't think that it's a ccfl, so possibly LED, but I don't recall the display assembly being thick enough to accommodate sufficiently powerful LEDs. Unless someone else knows, I'll see if I can dig the one I replaced a couple of weeks ago, back out of the workshop bin (un-emptied, and overflowing, as always !!) and see if I can see what lights it Arfa Yeah it's strange. It almost make me want to think it's LED backlit. I just don't see how those streaks would be there while lit with ccfl. And even when lit if you hold it in strong light the streaks disappear. When you pry apart the buckles that hold the top on, is there a special tool? The green tool in the video looked specialized just to pry the buckles apart on an Ipod. This unit was given to me at no cost so a new display is a definite option but my propensity towards repair makes me want to try to fix it first. If it's somehow LED backlit there might be some bad soldering. The previous owner told me the streaks appeared out of the blue, no reason. Also, have you have an IPod Touch apart? A neighbor kid has a 16 GB unit with an intermittent audio jack. I suppose it's a solder job but I'll have to figure out how to unbuckle it without breaking the glass. -- Live Fast, Die Young and Leave a Pretty Corpse |
#22
Posted to sci.electronics.repair
|
|||
|
|||
30 GB Video Ipod (was: Computer runs faster because it is soldered.. haha..
On Tue, 15 Feb 2011 18:54:49 +0000 (UTC) Meat Plow
wrote in Message id: : On Tue, 15 Feb 2011 02:17:39 +0000, Arfa Daily wrote: "Meat Plow" wrote in message news On Mon, 14 Feb 2011 01:44:27 +0000, Arfa Daily wrote: Just last week, I bought a replacement LCD assembly for a Classic, and it was £10.20 (say $15) including tax and delivery. I got it from my usual supplier here in the UK, and it looked as though it was a factory-original part. Good price. It probably came directly from China from the same factory that supplies the displays to Apple. I get quite a few parts that way through Hong Kong. However, there are some parts which are simply unobtainable new and/or at reasonable prices. Cosmetic parts, custom chips, and wear parts (i.e. power jacks, controls, keyboards, touchpads, hinges, rubber feet, etc) tend to be difficult to find. Most of these I buy from eBay vendors that cannibalize machines and sell the parts. Without used parts, many of the repairs that I'm doing would be either uneconomical or impossible. I could not build the business on purchasing new parts from the original manufacturer. -- Jeff Liebermann The company I use is http://www.parts4ipods.com Not much use to you as a leftpondian, but as you can see, they do a lot of Apple parts, including some cosmetics and touch screens. Arfa Hey how do I get my 30 GB Video Ipod apart? It has a .5mm streak going from right to left in the middle of the screen but stops just short of the left side. But it is in the backlighting because the streak does not appear in bright light. So it doesn't seem to be the LCD just the lighting. Does this sound right? I don't want to mess with trying to pry it apart and bend it all up but I would like to see if there is something that can be done first without buying a replacement panel. -- Live Fast, Die Young and Leave a Pretty Corpse I agree with Jeff. The problem is most likely the display itself or a connection to it. They come apart quite easily, once you have got one side started. there are lots of videos on You Tube. The English on this one is crap, but the actual video shows it all quite well, except that they don't show any screws down the sides once you have the case off. There have been tiny screws in all the ones I've seen, but they are obvious. http://www.youtube.com/watch?v=UYE9V...eature=related Trickiest bit I've found is when you come to put it back together, and you have to get the centre button in the control ring to stay correctly in place, as you try to get the ring to locate in the case front. Not ultimately hard exactly, just fiddly, and a bit frustrating the first ten times that it falls back out ... :-) Arfa How is it backlit? is it ccfl ? I don't understand when viewed in bright light after the backlight turns off the streak goes away. I can take a pic of it and put it on photobucket: This is with backlight: http://i273.photobucket.com/albums/jj220/meatplow1/Electronics/cimg0047.jpg This is with reflected light only: http://i273.photobucket.com/albums/jj220/meatplow1/Electronics/cimg0046.jpg As you can easily see the reflected light picture shows no anomaly on the screen. It's not just a case of the anomaly being too hard to see with reflected light. I know you say you never abused it, but it's almost like a scuff between the CFL and the rear of the LCD panel. That might explain why you only see when the backlight is on and light is (trying) to get though. IMO, it's too random to be the LCD panel itself. |
#23
Posted to sci.electronics.repair
|
|||
|
|||
30 GB Video Ipod (was: Computer runs faster because it issoldered.. haha..
On Wed, 16 Feb 2011 09:49:58 -0500, JW wrote:
On Tue, 15 Feb 2011 18:54:49 +0000 (UTC) Meat Plow wrote in Message id: : On Tue, 15 Feb 2011 02:17:39 +0000, Arfa Daily wrote: "Meat Plow" wrote in message news On Mon, 14 Feb 2011 01:44:27 +0000, Arfa Daily wrote: Just last week, I bought a replacement LCD assembly for a Classic, and it was £10.20 (say $15) including tax and delivery. I got it from my usual supplier here in the UK, and it looked as though it was a factory-original part. Good price. It probably came directly from China from the same factory that supplies the displays to Apple. I get quite a few parts that way through Hong Kong. However, there are some parts which are simply unobtainable new and/or at reasonable prices. Cosmetic parts, custom chips, and wear parts (i.e. power jacks, controls, keyboards, touchpads, hinges, rubber feet, etc) tend to be difficult to find. Most of these I buy from eBay vendors that cannibalize machines and sell the parts. Without used parts, many of the repairs that I'm doing would be either uneconomical or impossible. I could not build the business on purchasing new parts from the original manufacturer. -- Jeff Liebermann The company I use is http://www.parts4ipods.com Not much use to you as a leftpondian, but as you can see, they do a lot of Apple parts, including some cosmetics and touch screens. Arfa Hey how do I get my 30 GB Video Ipod apart? It has a .5mm streak going from right to left in the middle of the screen but stops just short of the left side. But it is in the backlighting because the streak does not appear in bright light. So it doesn't seem to be the LCD just the lighting. Does this sound right? I don't want to mess with trying to pry it apart and bend it all up but I would like to see if there is something that can be done first without buying a replacement panel. -- Live Fast, Die Young and Leave a Pretty Corpse I agree with Jeff. The problem is most likely the display itself or a connection to it. They come apart quite easily, once you have got one side started. there are lots of videos on You Tube. The English on this one is crap, but the actual video shows it all quite well, except that they don't show any screws down the sides once you have the case off. There have been tiny screws in all the ones I've seen, but they are obvious. http://www.youtube.com/watch?v=UYE9V...eature=related Trickiest bit I've found is when you come to put it back together, and you have to get the centre button in the control ring to stay correctly in place, as you try to get the ring to locate in the case front. Not ultimately hard exactly, just fiddly, and a bit frustrating the first ten times that it falls back out ... :-) Arfa How is it backlit? is it ccfl ? I don't understand when viewed in bright light after the backlight turns off the streak goes away. I can take a pic of it and put it on photobucket: This is with backlight: http://i273.photobucket.com/albums/j...1/Electronics/ cimg0047.jpg This is with reflected light only: http://i273.photobucket.com/albums/j...1/Electronics/ cimg0046.jpg As you can easily see the reflected light picture shows no anomaly on the screen. It's not just a case of the anomaly being too hard to see with reflected light. I know you say you never abused it, but it's almost like a scuff between the CFL and the rear of the LCD panel. That might explain why you only see when the backlight is on and light is (trying) to get though. IMO, it's too random to be the LCD panel itself. Seeing one apart I don't see how the back of the LCD could get scuffed. Nothing can really move being buckled in. Looking at the unit overall there are some scuffs and scratches that i would consider normal wear. Nothing along the lines of an impact. I may open it today if I can find the right plastic tool. -- Live Fast, Die Young and Leave a Pretty Corpse |
#24
Posted to sci.electronics.repair
|
|||
|
|||
30 GB Video Ipod (was: Computer runs faster because it is soldered.. haha..
On Tue, 15 Feb 2011 18:54:49 +0000 (UTC), Meat Plow
wrote: This is with backlight: http://i273.photobucket.com/albums/jj220/meatplow1/Electronics/cimg0047.jpg This is with reflected light only: http://i273.photobucket.com/albums/jj220/meatplow1/Electronics/cimg0046.jpg As you can easily see the reflected light picture shows no anomaly on the screen. It's not just a case of the anomaly being too hard to see with reflected light. Weird. I thought you meant a line, not a smear. The iPod and most Apple displays have a polarization filter as part of the display sandwich in order to improve the contrast without backlighting. Try wearing a pair of polarizing sunglasses and you'll see the display go black at some angle. My guess(tm) is that there's some damage to the polarizing screen. Change your viewing angle of the display showing the smear, and see if the black smear shifts with respect to the background image. If it does shift, then it's not on the LCD layer, but rather something above it, like the polarizing filter. If it doesn't shift, it's either the LCD or the backlighting layer. Any chance you could identify the exact model instead of just 30GB iPod? http://www.ifixit.com/Browse/iPod_Original -- Jeff Liebermann 150 Felker St #D http://www.LearnByDestroying.com Santa Cruz CA 95060 http://802.11junk.com Skype: JeffLiebermann AE6KS 831-336-2558 |
#25
Posted to sci.electronics.repair
|
|||
|
|||
30 GB Video Ipod (was: Computer runs faster because it issoldered.. haha..
On Wed, 16 Feb 2011 09:11:56 -0800, Jeff Liebermann wrote:
On Tue, 15 Feb 2011 18:54:49 +0000 (UTC), Meat Plow wrote: This is with backlight: http://i273.photobucket.com/albums/j...1/Electronics/ cimg0047.jpg This is with reflected light only: http://i273.photobucket.com/albums/j...1/Electronics/ cimg0046.jpg As you can easily see the reflected light picture shows no anomaly on the screen. It's not just a case of the anomaly being too hard to see with reflected light. Weird. I thought you meant a line, not a smear. The iPod and most Apple displays have a polarization filter as part of the display sandwich in order to improve the contrast without backlighting. Try wearing a pair of polarizing sunglasses and you'll see the display go black at some angle. My guess(tm) is that there's some damage to the polarizing screen. Change your viewing angle of the display showing the smear, and see if the black smear shifts with respect to the background image. If it does shift, then it's not on the LCD layer, but rather something above it, like the polarizing filter. If it doesn't shift, it's either the LCD or the backlighting layer. Any chance you could identify the exact model instead of just 30GB iPod? http://www.ifixit.com/Browse/iPod_Original Model A1136 Video Ipod, color. The lines or smears do not change when backlit and viewed at any angle. Nor do they appear when viewed at any angle with no backlight. There are no dents or dings of any kind on the unit. Just normal scuffing from being placed and removed from a protective leather case. This was previously owned by a relative who takes very good care of her things. She also has a 160 GB video Ipod and a Ipod Touch. I asked her if she can remember dropping it and she said no and that she would have remembered doing so. -- Live Fast, Die Young and Leave a Pretty Corpse |
#26
Posted to sci.electronics.repair
|
|||
|
|||
30 GB Video Ipod
"Meat Plow" wrote in message news On Wed, 16 Feb 2011 01:55:09 +0000, Arfa Daily wrote: Arfa How is it backlit? is it ccfl ? I don't understand when viewed in bright light after the backlight turns off the streak goes away. I can take a pic of it and put it on photobucket: This is with backlight: http://i273.photobucket.com/albums/j...1/Electronics/ cimg0047.jpg This is with reflected light only: http://i273.photobucket.com/albums/j...1/Electronics/ cimg0046.jpg As you can easily see the reflected light picture shows no anomaly on the screen. It's not just a case of the anomaly being too hard to see with reflected light. Hmmm. As you say, the display error does not appear to be there in the second picture, and I'm not sure just what to make of that. As to how the things are backlit, to be honest, I'm not sure. I don't think that it's a ccfl, so possibly LED, but I don't recall the display assembly being thick enough to accommodate sufficiently powerful LEDs. Unless someone else knows, I'll see if I can dig the one I replaced a couple of weeks ago, back out of the workshop bin (un-emptied, and overflowing, as always !!) and see if I can see what lights it Arfa Yeah it's strange. It almost make me want to think it's LED backlit. I just don't see how those streaks would be there while lit with ccfl. And even when lit if you hold it in strong light the streaks disappear. When you pry apart the buckles that hold the top on, is there a special tool? The green tool in the video looked specialized just to pry the buckles apart on an Ipod. This unit was given to me at no cost so a new display is a definite option but my propensity towards repair makes me want to try to fix it first. If it's somehow LED backlit there might be some bad soldering. The previous owner told me the streaks appeared out of the blue, no reason. Also, have you have an IPod Touch apart? A neighbor kid has a 16 GB unit with an intermittent audio jack. I suppose it's a solder job but I'll have to figure out how to unbuckle it without breaking the glass. You don't need any special tool to get the clips to spring - although some replacement batteries I've seen advertised, come with that tool to facilitate fitting by Joe Public. I use an Excelite scalpel with a blunt curved blade. It easily gets in there, and springs the clips. The Touch is also quite easy to get into, again using the scalpel. but you have to be careful not to crack the touchscreen. If you can find a piece of thin stiff plastic - maybe an old filed down credit card or something - it may be safer for your first attempt. The case springs off from the front. You have to get into the small crack between the glass of the touchscreen, and the metal case back, where it curves around to meet the glass. The LCD display, and touchscreen glass are fitted together into a thin plastic 'frame' that completely surrounds the four edges, and it is to this frame that the case is clipped. So, once you have started to insert your springing tool, before you have gone in too far, you need to bend the 'free' end of it in towards the screen, so that the inserted end is moving away from the crack. The tool tip will then slide down the outside of the thin frame, inside the metal cover. Once it has gone down there, you can bend the tool back up away from the screen, and this will flex the metal case off the plastic frame. Once it has started to open like this, it's just a case then of following round the four sides until it's off. It's that first insertion that's critical if you are using a metal blade. If you accidentally get between the thin plastic frame and the glass, when you try to flex the case off, you will instead crack the display. Don't ask me how I know this ... All of the component parts of the display are available for very reasonable prices, but the frame, touchscreen and display form a well-stuck-together assembly, and it's a lot of effort to successfully get it apart to replace either a broken touchscreen, or display, so you end up buying a replacement ready assembled unit. If you look on that parts site I pointed you at, I think that they have a picture of the assembly, so you can see what I mean about the thin frame that you have to be on the outside of, when you insert your tool (!) I'm sure that there are probably dismantling videos on You Tube, as well. The headphone problem will not be a soldering job. The sockets are notorious for going bad (also on Classics). The good news is that once you're inside the unit, it is a straightforward job to replace it. It comes complete on its own flexiprint, ready to just plug in to a little zif connector, and it is extremely reasonably priced. I think I paid just a few quid delivered for the last one I got - say $5 in leftpondian wonga. One last thing to watch out for. The touchscreen is connected to the main board with an almost microscopic plug on the end of its flexiprint. It's very tricky to get it to reconnect correctly the first time you ever do one. It's a bit like one of those tiny tiny coax plugs that you find on the wifi antenna in laptops, in that delicate as it *appears* to be, it actually needs to be pushed *really* firmly once you are happy that it is sitting squarely over the socket on the main board. It will then go with a really solid click. If it doesn't do this, your touchscreen will be intermittent or inoperative when you get the unit all back together. The thing that makes this final operation tricky to do, is that the flexiprint 'tail' with the plug on it, is very short. With a bit of care, I wouldn't expect someone of your experience to struggle too much with the job. Let us know how you get on with it. Arfa |
#27
Posted to sci.electronics.repair
|
|||
|
|||
30 GB Video Ipod
On Thu, 17 Feb 2011 02:38:07 +0000, Arfa Daily wrote:
"Meat Plow" wrote in message news On Wed, 16 Feb 2011 01:55:09 +0000, Arfa Daily wrote: Arfa How is it backlit? is it ccfl ? I don't understand when viewed in bright light after the backlight turns off the streak goes away. I can take a pic of it and put it on photobucket: This is with backlight: http://i273.photobucket.com/albums/j...1/Electronics/ cimg0047.jpg This is with reflected light only: http://i273.photobucket.com/albums/j...1/Electronics/ cimg0046.jpg As you can easily see the reflected light picture shows no anomaly on the screen. It's not just a case of the anomaly being too hard to see with reflected light. Hmmm. As you say, the display error does not appear to be there in the second picture, and I'm not sure just what to make of that. As to how the things are backlit, to be honest, I'm not sure. I don't think that it's a ccfl, so possibly LED, but I don't recall the display assembly being thick enough to accommodate sufficiently powerful LEDs. Unless someone else knows, I'll see if I can dig the one I replaced a couple of weeks ago, back out of the workshop bin (un-emptied, and overflowing, as always !!) and see if I can see what lights it Arfa Yeah it's strange. It almost make me want to think it's LED backlit. I just don't see how those streaks would be there while lit with ccfl. And even when lit if you hold it in strong light the streaks disappear. When you pry apart the buckles that hold the top on, is there a special tool? The green tool in the video looked specialized just to pry the buckles apart on an Ipod. This unit was given to me at no cost so a new display is a definite option but my propensity towards repair makes me want to try to fix it first. If it's somehow LED backlit there might be some bad soldering. The previous owner told me the streaks appeared out of the blue, no reason. Also, have you have an IPod Touch apart? A neighbor kid has a 16 GB unit with an intermittent audio jack. I suppose it's a solder job but I'll have to figure out how to unbuckle it without breaking the glass. You don't need any special tool to get the clips to spring - although some replacement batteries I've seen advertised, come with that tool to facilitate fitting by Joe Public. I use an Excelite scalpel with a blunt curved blade. It easily gets in there, and springs the clips. The Touch is also quite easy to get into, again using the scalpel. but you have to be careful not to crack the touchscreen. If you can find a piece of thin stiff plastic - maybe an old filed down credit card or something - it may be safer for your first attempt. The case springs off from the front. You have to get into the small crack between the glass of the touchscreen, and the metal case back, where it curves around to meet the glass. The LCD display, and touchscreen glass are fitted together into a thin plastic 'frame' that completely surrounds the four edges, and it is to this frame that the case is clipped. So, once you have started to insert your springing tool, before you have gone in too far, you need to bend the 'free' end of it in towards the screen, so that the inserted end is moving away from the crack. The tool tip will then slide down the outside of the thin frame, inside the metal cover. Once it has gone down there, you can bend the tool back up away from the screen, and this will flex the metal case off the plastic frame. Once it has started to open like this, it's just a case then of following round the four sides until it's off. It's that first insertion that's critical if you are using a metal blade. If you accidentally get between the thin plastic frame and the glass, when you try to flex the case off, you will instead crack the display. Don't ask me how I know this ... All of the component parts of the display are available for very reasonable prices, but the frame, touchscreen and display form a well-stuck-together assembly, and it's a lot of effort to successfully get it apart to replace either a broken touchscreen, or display, so you end up buying a replacement ready assembled unit. If you look on that parts site I pointed you at, I think that they have a picture of the assembly, so you can see what I mean about the thin frame that you have to be on the outside of, when you insert your tool (!) I'm sure that there are probably dismantling videos on You Tube, as well. The headphone problem will not be a soldering job. The sockets are notorious for going bad (also on Classics). The good news is that once you're inside the unit, it is a straightforward job to replace it. It comes complete on its own flexiprint, ready to just plug in to a little zif connector, and it is extremely reasonably priced. I think I paid just a few quid delivered for the last one I got - say $5 in leftpondian wonga. One last thing to watch out for. The touchscreen is connected to the main board with an almost microscopic plug on the end of its flexiprint. It's very tricky to get it to reconnect correctly the first time you ever do one. It's a bit like one of those tiny tiny coax plugs that you find on the wifi antenna in laptops, in that delicate as it *appears* to be, it actually needs to be pushed *really* firmly once you are happy that it is sitting squarely over the socket on the main board. It will then go with a really solid click. If it doesn't do this, your touchscreen will be intermittent or inoperative when you get the unit all back together. The thing that makes this final operation tricky to do, is that the flexiprint 'tail' with the plug on it, is very short. With a bit of care, I wouldn't expect someone of your experience to struggle too much with the job. Let us know how you get on with it. Arfa Will do mate thanks for taking the time to explain in that detail. it boosts my confidence tremendously. I'll tackle the 30 tomorrow I'm very curious just what the damn screen is made of. -- Live Fast, Die Young and Leave a Pretty Corpse |
Reply |
Thread Tools | Search this Thread |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Forum | |||
Haha-I was wondering why this floor was sunk down | Home Repair | |||
Breaking a soldered joint | Home Repair | |||
"Easy" (haha) stump removal? | Home Repair | |||
Soldered cable ends? | UK diy |