Home |
Search |
Today's Posts |
|
Home Repair (alt.home.repair) For all homeowners and DIYers with many experienced tradesmen. Solve your toughest home fix-it problems. |
Reply |
|
LinkBack | Thread Tools | Display Modes |
#1
|
|||
|
|||
How to Frost Garage Windows for Privacy ?
I just had a rollup garage door installed that has windows which will allow
daylight (good) and a view of the electronics and tools in my garage (bad). The windows that came with the door are clear glass. What can I use to obscure the view from outside without losing the natural light? Some searching came up with two potential solutions: 1) Spray on fogging paint, apparently available from craft stores; and 2) Aquarium crystal paint. I believe that any tinted or reflective film will work except that, at night, someone would be able to see into the lit garage. That's almost a good enough fix, but not quite. I also understand that I cannot add any appreciable weight to the door, so that rules out adding a thin sheet of bubbled light fixture panes (like on flourecent lights). I'd appreciate any shared experiences on this. Thanks. - Magnusfarce |
#2
|
|||
|
|||
you'll lose most of the natural light (can be overcome with interior
lighting) but some dark colored plastic window screen stapled over the window openings from inside, using more than one layer if one layer is too transparent for your liking, might work just staple along the top (not the sides or bottom) then the screen or layers of screen can be lifted and temporarily clipped in place (clothes pins, etc.) to increase lighting when the garage is being used another arrangement might be to add a solid panel of thin plywood etc. about the size of each window, permanently shimmed back from the window a couple inches between it and the window, so light could pass through all around through the couple inches space,,,hard to engineer mentally without seeing the doors or you could cover each window from inside with some solid panels (plywood etc.) and have each one hinged so they can be opened to allow light in whenever; also have some kind of securing mechanism on each so when the garage door is raised they stay put or use a combination of solid panels and screen and if you have the bux, electric glass http://www.electricglasswall.com/photo.htm "Magnusfarce" wrote in message ... I just had a rollup garage door installed that has windows which will allow daylight (good) and a view of the electronics and tools in my garage (bad). The windows that came with the door are clear glass. What can I use to obscure the view from outside without losing the natural light? Some searching came up with two potential solutions: 1) Spray on fogging paint, apparently available from craft stores; and 2) Aquarium crystal paint. I believe that any tinted or reflective film will work except that, at night, someone would be able to see into the lit garage. That's almost a good enough fix, but not quite. I also understand that I cannot add any appreciable weight to the door, so that rules out adding a thin sheet of bubbled light fixture panes (like on flourecent lights). I'd appreciate any shared experiences on this. Thanks. - Magnusfarce |
#3
|
|||
|
|||
In article ,
"Magnusfarce" wrote: - I just had a rollup garage door installed that has windows which will allow - daylight (good) and a view of the electronics and tools in my garage (bad). - The windows that came with the door are clear glass. What can I use to - obscure the view from outside without losing the natural light? - - Some searching came up with two potential solutions: 1) Spray on fogging - paint, apparently available from craft stores; and 2) Aquarium crystal - paint. - - I believe that any tinted or reflective film will work except that, at - night, someone would be able to see into the lit garage. That's almost a - good enough fix, but not quite. I also understand that I cannot add any - appreciable weight to the door, so that rules out adding a thin sheet of - bubbled light fixture panes (like on flourecent lights). - - I'd appreciate any shared experiences on this. Thanks. Someone, somewhere sells a sort of plastic sheeting (much like shelf "paper") that is intended for use on bathroom windows. It give a frosted appearance when attached to the window. Unfortunately, I don't recall where I've seen it. -- 8^)~~~ Sue (remove the x to e-mail) ~~~~~~ "I reserve the absolute right to be smarter today than I was yesterday." -Adlai Stevenson http://www.suzanne-eckhardt.com/ ***Revelation 22:12*** ICQ: 349878998 http://www.intergnat.com/malebashing/ |
#4
|
|||
|
|||
In article ,
Suzie-Q wrote: - In article , - "Magnusfarce" wrote: - - - I just had a rollup garage door installed that has windows which will - allow - - daylight (good) and a view of the electronics and tools in my garage - (bad). - - The windows that came with the door are clear glass. What can I use to - - obscure the view from outside without losing the natural light? - - - - Some searching came up with two potential solutions: 1) Spray on - fogging - - paint, apparently available from craft stores; and 2) Aquarium crystal - - paint. - - - - I believe that any tinted or reflective film will work except that, at - - night, someone would be able to see into the lit garage. That's almost a - - good enough fix, but not quite. I also understand that I cannot add any - - appreciable weight to the door, so that rules out adding a thin sheet of - - bubbled light fixture panes (like on flourecent lights). - - - - I'd appreciate any shared experiences on this. Thanks. - - - Someone, somewhere sells a sort of plastic sheeting (much like - shelf "paper") that is intended for use on bathroom windows. It - give a frosted appearance when attached to the window. - - Unfortunately, I don't recall where I've seen it. Ooooooooh. Check this out: http://www.decorativefilm.com/ -- 8^)~~~ Sue (remove the x to e-mail) ~~~~~~ "I reserve the absolute right to be smarter today than I was yesterday." -Adlai Stevenson http://www.suzanne-eckhardt.com/ ***Revelation 22:12*** ICQ: 349878998 http://www.intergnat.com/malebashing/ |
#5
|
|||
|
|||
interesting film, the warehouse home improvement stores carry similar films
in limited small sizes sheet plastic or wax paper attached over the windows might also work to alter transparency while allowing light through "Suzie-Q" wrote in message news:sme617x- Ooooooooh. Check this out: http://www.decorativefilm.com/ -- 8^)~~~ Sue (remove the x to e-mail) ~~~~~~ "I reserve the absolute right to be smarter today than I was yesterday." -Adlai Stevenson http://www.suzanne-eckhardt.com/ ***Revelation 22:12*** ICQ: 349878998 http://www.intergnat.com/malebashing/ |
#6
|
|||
|
|||
Magnusfarce wrote:
I just had a rollup garage door installed that has windows which will allow daylight (good) and a view of the electronics and tools in my garage (bad). The windows that came with the door are clear glass. What can I use to obscure the view from outside without losing the natural light? Some searching came up with two potential solutions: 1) Spray on fogging paint, apparently available from craft stores; and 2) Aquarium crystal paint. I believe that any tinted or reflective film will work except that, at night, someone would be able to see into the lit garage. That's almost a good enough fix, but not quite. I also understand that I cannot add any appreciable weight to the door, so that rules out adding a thin sheet of bubbled light fixture panes (like on flourecent lights). I'd appreciate any shared experiences on this. Thanks. - Magnusfarce Since it is winter you need some additional insulation anyway. Just get regular plastic used for paint spatter (2-4 mil) which is milky and staple if you have a wood door or tape if you have a metal door. Look through the plastic to find a degree of translucency that you like. |
#7
|
|||
|
|||
"Suzie-Q" wrote Someone, somewhere sells a sort of plastic sheeting (much like shelf "paper") that is intended for use on bathroom windows. It give a frosted appearance when attached to the window. I know WallWorld used to sell it. It was with all the other rolls of contact paper (do people still use that stuff?) made by Rubbermaid. They used to have a couple different "frosted" type ones. I used it years ago on my work truck to keep theives from "taking inventory"..... |
#8
|
|||
|
|||
On 1/8/2005 12:44 AM US(ET), Magnusfarce took fingers to keys, and typed
the following: I just had a rollup garage door installed that has windows which will allow daylight (good) and a view of the electronics and tools in my garage (bad). The windows that came with the door are clear glass. What can I use to obscure the view from outside without losing the natural light? Some searching came up with two potential solutions: 1) Spray on fogging paint, apparently available from craft stores; and 2) Aquarium crystal paint. I believe that any tinted or reflective film will work except that, at night, someone would be able to see into the lit garage. That's almost a good enough fix, but not quite. I also understand that I cannot add any appreciable weight to the door, so that rules out adding a thin sheet of bubbled light fixture panes (like on flourecent lights). I'd appreciate any shared experiences on this. Thanks. - Magnusfarce Take a run over to WalMart or any store that sells "Con-Tact" plastic shelving paper. They have a diamond patterned (peel and stick) semi-clear plastic film that can be used on window glass. I have it on one bathroom window that is next to a patio and it works great. -- Bill |
#9
|
|||
|
|||
Magnusfarce wrote:
I just had a rollup garage door installed that has windows which will allow daylight (good) and a view of the electronics and tools in my garage (bad). The windows that came with the door are clear glass. What can I use to obscure the view from outside without losing the natural light? Some searching came up with two potential solutions: 1) Spray on fogging paint, apparently available from craft stores; and 2) Aquarium crystal paint. I believe that any tinted or reflective film will work except that, at night, someone would be able to see into the lit garage. That's almost a good enough fix, but not quite. I also understand that I cannot add any appreciable weight to the door, so that rules out adding a thin sheet of bubbled light fixture panes (like on flourecent lights). I'd appreciate any shared experiences on this. Thanks. - Magnusfarce First, if you are in a creative mood, check out the craft stores for stain glass paint. Just add a little creativity and you can have a good looking results that also block vision well and not too much light. From Michaels http://www.michaels.com/art/online/d...002&channelid= However for most, I suggest the self stick plastic stuff sold for bathroom windows. A number of places carry it, try your local home improvement store. Home Depot has this listed under "window film." http://www.homedepot.com/prel80/HDUS...D=9876--Joseph Meehan26 + 6 = 1 It's Irish Math |
#10
|
|||
|
|||
On 1/8/2005 7:49 AM US(ET), willshak took fingers to keys, and typed the
following: On 1/8/2005 12:44 AM US(ET), Magnusfarce took fingers to keys, and typed the following: I just had a rollup garage door installed that has windows which will allow daylight (good) and a view of the electronics and tools in my garage (bad). The windows that came with the door are clear glass. What can I use to obscure the view from outside without losing the natural light? Some searching came up with two potential solutions: 1) Spray on fogging paint, apparently available from craft stores; and 2) Aquarium crystal paint. I believe that any tinted or reflective film will work except that, at night, someone would be able to see into the lit garage. That's almost a good enough fix, but not quite. I also understand that I cannot add any appreciable weight to the door, so that rules out adding a thin sheet of bubbled light fixture panes (like on flourecent lights). I'd appreciate any shared experiences on this. Thanks. - Magnusfarce Take a run over to WalMart or any store that sells "Con-Tact" plastic shelving paper. They have a diamond patterned (peel and stick) semi-clear plastic film that can be used on window glass. I have it on one bathroom window that is next to a patio and it works great. First, you have to cut me a little slack because of my age and CRS. I just realized that my garage door windows are covered with auto window tint that I installed myself some 20 years ago. They work great looking out during the day, but I can't see in too well. The only time you can see in pretty clearly, is when the garage lights are on. The film can be bought at any auto supply store like Autozone, CarQuest, etc. You can get it in many different colors and levels of opacity. Get the smoke tint unless you like the bronze or mirrored look of glass. Mine is the darker smoke shade, but not the real dark limo tint. -- Bill |
#11
|
|||
|
|||
Frosting a Window
Mix Epsom Salt with stale beer until the beer can hold no more. Then, apply the mixture to the glass. When it dries the window will be frosted. CL "Magnusfarce" wrote in message ... I just had a rollup garage door installed that has windows which will allow daylight (good) and a view of the electronics and tools in my garage (bad). The windows that came with the door are clear glass. What can I use to obscure the view from outside without losing the natural light? Some searching came up with two potential solutions: 1) Spray on fogging paint, apparently available from craft stores; and 2) Aquarium crystal paint. I believe that any tinted or reflective film will work except that, at night, someone would be able to see into the lit garage. That's almost a good enough fix, but not quite. I also understand that I cannot add any appreciable weight to the door, so that rules out adding a thin sheet of bubbled light fixture panes (like on flourecent lights). I'd appreciate any shared experiences on this. Thanks. - Magnusfarce |
#12
|
|||
|
|||
The spray on glass frosting available from most hardware stores and hobby
centers works quite well. You will need a razor blade to remove it if you change your mind. "Magnusfarce" wrote in message ... I just had a rollup garage door installed that has windows which will allow daylight (good) and a view of the electronics and tools in my garage (bad). The windows that came with the door are clear glass. What can I use to obscure the view from outside without losing the natural light? Some searching came up with two potential solutions: 1) Spray on fogging paint, apparently available from craft stores; and 2) Aquarium crystal paint. I believe that any tinted or reflective film will work except that, at night, someone would be able to see into the lit garage. That's almost a good enough fix, but not quite. I also understand that I cannot add any appreciable weight to the door, so that rules out adding a thin sheet of bubbled light fixture panes (like on flourecent lights). I'd appreciate any shared experiences on this. Thanks. - Magnusfarce |
#13
|
|||
|
|||
well you could do like I did,
car wax, but don't buff the haze. "Magnusfarce" wrote in message ... I just had a rollup garage door installed that has windows which will allow daylight (good) and a view of the electronics and tools in my garage (bad). The windows that came with the door are clear glass. What can I use to obscure the view from outside without losing the natural light? Some searching came up with two potential solutions: 1) Spray on fogging paint, apparently available from craft stores; and 2) Aquarium crystal paint. I believe that any tinted or reflective film will work except that, at night, someone would be able to see into the lit garage. That's almost a good enough fix, but not quite. I also understand that I cannot add any appreciable weight to the door, so that rules out adding a thin sheet of bubbled light fixture panes (like on flourecent lights). I'd appreciate any shared experiences on this. Thanks. - Magnusfarce |
#14
|
|||
|
|||
they used to use "GlassWax" like that. I think they still sell it
on the oldfashioned type hardware stores. bill "bumtracks" wrote in message news:eNUDd.691$SS6.434@trnddc07... well you could do like I did, car wax, but don't buff the haze. |
#15
|
|||
|
|||
I just had a rollup garage door installed that has windows which will
allow daylight (good) and a view of the electronics and tools in my garage (bad). The windows that came with the door are clear glass. What can I use to obscure the view from outside without losing the natural light? How about making some kind of "shades" for the windows? Assuming your door is metal, you could glue or tape some magnets to posterboard and "stick" the covers to the door when you want to block out the light. This gives you the advantage of being able to take the shades off to get the light in the garage when you want it. If you really want to get fancy, you could sew some magnets into the edges of some cloth shades. Most craft stores sell strips of magnetic material. We used them to stick christmas cards to our metal doors for years. If your doors are wood, you could probably install snaps, hooks, or some other method of attaching the shades to the door. Good luck, Anthony |
#16
|
|||
|
|||
I just had a roll up garage door installed that has windows which will allow
daylight (good) and a view of the electronics and tools in my garage (bad). The windows that came with the door are clear glass. What can I use to obscure the view from outside without losing the natural light? --------------- Krylon Glass frosting: http://krylon.com/main/product_templ...roduct_details Acrylic matte gel: http://megan.scatterbrain.org/notmar...wfrosting.html |
#17
|
|||
|
|||
On Fri, 7 Jan 2005 21:44:24 -0800, "Magnusfarce"
wrote: I just had a rollup garage door installed that has windows which will allow daylight (good) and a view of the electronics and tools in my garage (bad). The windows that came with the door are clear glass. What can I use to obscure the view from outside without losing the natural light? Some searching came up with two potential solutions: 1) Spray on fogging paint, apparently available from craft stores; and 2) Aquarium crystal paint. I believe that any tinted or reflective film will work except that, at night, someone would be able to see into the lit garage. That's almost a good enough fix, but not quite. I also understand that I cannot add any appreciable weight to the door, so that rules out adding a thin sheet of bubbled light fixture panes (like on flourecent lights). I'd appreciate any shared experiences on this. Thanks. - Magnusfarce I've used this on bathroom windows. Just make sure you follow directions. http://www.urlbee.com?497 later, tom |
#18
|
|||
|
|||
I agree with the plastic film. It is a vinyl plastic with a square or
diamond pattern that lets most of the light through, yet completley obscures what is behind it. I used it on my garage windows. If you apply it carfully, it looks like the pattern is part of the glass. John "Magnusfarce" wrote in message ... I just had a rollup garage door installed that has windows which will allow daylight (good) and a view of the electronics and tools in my garage (bad). The windows that came with the door are clear glass. What can I use to obscure the view from outside without losing the natural light? Some searching came up with two potential solutions: 1) Spray on fogging paint, apparently available from craft stores; and 2) Aquarium crystal paint. I believe that any tinted or reflective film will work except that, at night, someone would be able to see into the lit garage. That's almost a good enough fix, but not quite. I also understand that I cannot add any appreciable weight to the door, so that rules out adding a thin sheet of bubbled light fixture panes (like on flourecent lights). I'd appreciate any shared experiences on this. Thanks. - Magnusfarce |
#19
|
|||
|
|||
Suzie-Q wrote:
Someone, somewhere sells a sort of plastic sheeting (much like shelf "paper") that is intended for use on bathroom windows. It give a frosted appearance when attached to the window. ************************************************** ************************* Yes, I got some of this at Home Depot. I had originally seen it advertised in a catalogue, but I couldn't find the catalog, so I went to Home Depot and asked for that clear/opaque contact paper that you can put up on bathroom windows for privacy. You can't see through it, but light does get through. I've used this on garage windows and bathroom windows. It's probably the least elegant, but also the least expensive, way of dealing with the problem. You could start out by trying it, and then if you'd prefer something else, you can just peel off the contact paper and try something else. |
#20
|
|||
|
|||
Magnusfarce wrote:
I just had a rollup garage door installed that has windows which will allow daylight (good) and a view of the electronics and tools in my garage (bad). The windows that came with the door are clear glass. What can I use to obscure the view from outside without losing the natural light? Some searching came up with two potential solutions: 1) Spray on fogging paint, apparently available from craft stores; and 2) Aquarium crystal paint. I believe that any tinted or reflective film will work except that, at night, someone would be able to see into the lit garage. That's almost a good enough fix, but not quite. I also understand that I cannot add any appreciable weight to the door, so that rules out adding a thin sheet of bubbled light fixture panes (like on flourecent lights). I'd appreciate any shared experiences on this. Thanks. - Magnusfarce Sandblast it. Seriously, Bob |
#21
|
|||
|
|||
Magnusfarce wrote: I just had a rollup garage door installed that has windows which will allow daylight (good) and a view of the electronics and tools in my garage (bad). The windows that came with the door are clear glass. What can I use to obscure the view from outside without losing the natural light? Some searching came up with two potential solutions: 1) Spray on fogging paint, apparently available from craft stores; and 2) Aquarium crystal paint. I believe that any tinted or reflective film will work except that, at night, someone would be able to see into the lit garage. That's almost a good enough fix, but not quite. I also understand that I cannot add any appreciable weight to the door, so that rules out adding a thin sheet of bubbled light fixture panes (like on flourecent lights). I'd appreciate any shared experiences on this. Thanks. - Magnusfarce I have sheer window curtains with a small cafe rod top and bottom. Easy to make with minimum sewing, and stays in place when the door is raised. |
#22
|
|||
|
|||
"Bubba" wrote in message
... Yall liss'n here. I kaint believe all the ghetta responses, chit why not just duck tape plastic Wal-mart bags over the winders. Ya reckon? the op indicated translucency is "good" the bags ain't as translucent as something more translucent is this lucid? |
#23
|
|||
|
|||
Magnusfarce wrote:
I just had a rollup garage door installed that has windows which will allow daylight (good) and a view of the electronics and tools in my garage (bad). The windows that came with the door are clear glass. What can I use to obscure the view from outside without losing the natural light? Some searching came up with two potential solutions: 1) Spray on fogging paint, apparently available from craft stores; and 2) Aquarium crystal paint. I believe that any tinted or reflective film will work except that, at night, someone would be able to see into the lit garage. That's almost a good enough fix, but not quite. I also understand that I cannot add any appreciable weight to the door, so that rules out adding a thin sheet of bubbled light fixture panes (like on flourecent lights). I'd appreciate any shared experiences on this. Thanks. - Magnusfarce Instead of a garage this applies to rear facing windows. New construction behind me makes me wish to alter the transparency of my windows. First thought is a reflective film that would allow persons inside to easily see out but block viewing from outside. Day and night. Suggestions? |
#24
|
|||
|
|||
Magnusfarce wrote: I just had a rollup garage door installed that has windows which will allow daylight (good) and a view of the electronics and tools in my garage (bad). The windows that came with the door are clear glass. What can I use to obscure the view from outside without losing the natural light? Another consideration is the placement of the panels. If the lights are at the top, they are least visible compared to the seconds from the top. |
#25
|
|||
|
|||
"Jim" wrote in message
... Magnusfarce wrote: I just had a rollup garage door installed that has windows which will allow daylight (good) and a view of the electronics and tools in my garage (bad). The windows that came with the door are clear glass. What can I use to obscure the view from outside without losing the natural light? Some searching came up with two potential solutions: 1) Spray on fogging paint, apparently available from craft stores; and 2) Aquarium crystal paint. I believe that any tinted or reflective film will work except that, at night, someone would be able to see into the lit garage. That's almost a good enough fix, but not quite. I also understand that I cannot add any appreciable weight to the door, so that rules out adding a thin sheet of bubbled light fixture panes (like on flourecent lights). I'd appreciate any shared experiences on this. Thanks. - Magnusfarce Instead of a garage this applies to rear facing windows. New construction behind me makes me wish to alter the transparency of my windows. First thought is a reflective film that would allow persons inside to easily see out but block viewing from outside. Day and night. Suggestions? http://www.llumar.com/na-eng/Decorative/deco.html curtains? plant a hedge? build a tall fence? |
#26
|
|||
|
|||
On Sun, 09 Jan 2005 21:30:32 GMT, "Edwin Pawlowski"
wrote: Magnusfarce wrote: I just had a rollup garage door installed that has windows which will allow daylight (good) and a view of the electronics and tools in my garage (bad). The windows that came with the door are clear glass. What can I use to obscure the view from outside without losing the natural light? Wax Paper? Beachcomber |
#27
|
|||
|
|||
Heat up your pot o "hide glue". Ladle some on any window, then stand back as
she dries. It pings off the glass and gives frosted look. |
#28
|
|||
|
|||
"Magnusfarce" wrote in message ... I just had a rollup garage door installed that has windows which will allow daylight (good) and a view of the electronics and tools in my garage (bad). The windows that came with the door are clear glass. What can I use to obscure the view from outside without losing the natural light? Some searching came up with two potential solutions: 1) Spray on fogging paint, apparently available from craft stores; and 2) Aquarium crystal paint. I believe that any tinted or reflective film will work except that, at night, someone would be able to see into the lit garage. That's almost a good enough fix, but not quite. I also understand that I cannot add any appreciable weight to the door, so that rules out adding a thin sheet of bubbled light fixture panes (like on flourecent lights). I'd appreciate any shared experiences on this. Thanks. - Magnusfarce 1. Hit it with a sandblaster or 2. Etch it with hydrofluoric acid. |
#29
|
|||
|
|||
Bubba wrote:
Yall liss'n here. I kaint believe all the ghetta responses, chit why not just duck tape plastic Wal-mart bags over the winders. Ya reckon? You can laugh, but I used a roll of brown paper like they use to wrap packages for the post office on mine, leaving a slit window for me to look out along the tops of the windows. I just stretched out a piece long enough to reach across all four panes and secured it with thumb tacks. Since the outside of the door is a kind of bronze color, the combination is actually pretty attractive and now I don't have to sweat one of the neighbors looking in and seeing me working out there in my boxers. It cost essentially nothing, lasted almost ten years before I had to replace it, and is instantly reversible if you need it to disappear for some reason. -- Mortimer Schnerd, RN VE |
#30
|
|||
|
|||
"Mortimer Schnerd, RN" writes:
Bubba wrote: Yall liss'n here. I kaint believe all the ghetta responses, chit why not just duck tape plastic Wal-mart bags over the winders. Ya reckon? I used a roll of brown paper [...] on mine, leaving a slit window Another option is to find a store still selling holiday leftovers and look for with spray frost or spray snow. OR You can make your own frost mix by saturating isopropol alcohol with epsom salts and a *little* table salt. Just mix it and sponge on the windows. (I imagine a spray bottle would work if you just "misted" the window) http://www.google.com/search?q=frost...dow+epsom+salt Some of these say use beer, other say water. I suggested isopropol since it will evap quickly and not leave any organics like beer will. A slight word of warning, the salt is hydrophilic (attracts water)... I wouldn't use it in a high humidity enviroment. Good luck -- be safe. flip Ich habe keine Ahnung was das bedeutet, oder vielleicht doch? Remove origin of the word spam from address to reply (leave "+") |
#31
|
|||
|
|||
buy some frosted glass spray.
"The winds of God are always blowing, but you must set the sails" |
#32
Posted to alt.home.repair
|
|||
|
|||
How to Frost Garage Windows for Privacy ?
replying to Magnusfarce, easyfix wrote:
Question: with these loose covers - tape at top only, etc. do they not get in the way of the door opening mechanisms, chain, etc. when the door is opened? -- for full context, visit https://www.homeownershub.com/mainte...cy-582719-.htm |
#33
Posted to alt.home.repair
|
|||
|
|||
How to Frost Garage Windows for Privacy ?
On Wednesday, May 10, 2017 at 5:44:06 PM UTC-5, easyfix wrote:
replying to Magnusfarce, easyfix wrote: Question: with these loose covers - tape at top only, etc. do they not get in the way of the door opening mechanisms, chain, etc. when the door is opened? for full context, visit https://www.homeownershub.com/mainte...cy-582719-.htm Another clueless dope from HomeMoanersHub dragging up a TWELVE YEAR OLD post. They're answering just like they thought the original poster was hanging around all these years awaiting their advice. |
Reply |
Thread Tools | Search this Thread |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Forum | |||
Childproofing Windows | Home Repair | |||
Building an Extension (Garage and Block Selection) | UK diy | |||
Newpro - Avoid them at ALL costs! | Home Ownership | |||
adding on to our house - which windows? | Home Ownership | |||
[OT] Car insurance craziness | UK diy |