Home |
Search |
Today's Posts |
|
Metalworking (rec.crafts.metalworking) Discuss various aspects of working with metal, such as machining, welding, metal joining, screwing, casting, hardening/tempering, blacksmithing/forging, spinning and hammer work, sheet metal work. |
Reply |
|
|
LinkBack | Thread Tools | Display Modes |
#1
Posted to rec.crafts.metalworking
|
|||
|
|||
Unique Need for Torx/Star bits.
Hi, members.
I need ~T-10 Torx bit material that runs more than the conventional 3/8" down the length. I really need 2 or 3 feet or more lengths. I can't seem to find this anywhere. If it doesn't exist, does anyone have any suggestions on how to make it? I may need 50 pieces at a time. Thanks j/b |
#2
Posted to rec.crafts.metalworking
|
|||
|
|||
Unique Need for Torx/Star bits.
jusme wrote:
Hi, members. I need ~T-10 Torx bit material that runs more than the conventional 3/8" down the length. I really need 2 or 3 feet or more lengths. I can't seem to find this anywhere. If it doesn't exist, does anyone have any suggestions on how to make it? I may need 50 pieces at a time. Thanks j/b Can supply 4340 @ $40 per foot inclusive of HT, minimum order 200 lineal feet. Leon |
#3
Posted to rec.crafts.metalworking
|
|||
|
|||
Unique Need for Torx/Star bits.
Thanks for the offer, Leon. I am prototyping something that MAY go on a
very, very limited market so, I can't afford that. Can anyone tell me how to make it myself? I have lathe, mill, BIG shaper, etc. j/b "Leon" wrote in message ... jusme wrote: Hi, members. I need ~T-10 Torx bit material that runs more than the conventional 3/8" down the length. I really need 2 or 3 feet or more lengths. I can't seem to find this anywhere. If it doesn't exist, does anyone have any suggestions on how to make it? I may need 50 pieces at a time. Thanks j/b Can supply 4340 @ $40 per foot inclusive of HT, minimum order 200 lineal feet. Leon |
#4
Posted to rec.crafts.metalworking
|
|||
|
|||
Unique Need for Torx/Star bits.
Doesn't anyone have any information on how to make such an item? Is it so
obvious that I am overlooking it? Thanks j/b "jusme" wrote in message ... Hi, members. I need ~T-10 Torx bit material that runs more than the conventional 3/8" down the length. I really need 2 or 3 feet or more lengths. I can't seem to find this anywhere. If it doesn't exist, does anyone have any suggestions on how to make it? I may need 50 pieces at a time. Thanks j/b |
#5
Posted to rec.crafts.metalworking
|
|||
|
|||
Unique Need for Torx/Star bits.
On Dec 28, 11:10 am, "jusme" wrote:
Doesn't anyone have any information on how to make such an item? Is it so obvious that I am overlooking it? Thanks j/b "jusme" wrote in message ... Hi, members. I need ~T-10 Torx bit material that runs more than the conventional 3/8" down the length. I really need 2 or 3 feet or more lengths. I can't seem to find this anywhere. If it doesn't exist, does anyone have any suggestions on how to make it? I may need 50 pieces at a time. Thanks j/b Before I go to a lot of trouble, a few questions. Do you have an indexing head? Cutter grinder? What tolerances do you require? Material? What stresses will be applied? Any other specifications that need to be met? Dave |
#6
Posted to rec.crafts.metalworking
|
|||
|
|||
Unique Need for Torx/Star bits.
On Fri, 28 Dec 2007 13:10:16 -0600, "jusme" wrote:
Doesn't anyone have any information on how to make such an item? Is it so obvious that I am overlooking it? Thanks j/b Wellll...first thing you need is a nice 150 ton cold header or 50 ton hot header....... 400 amps of 480 3ph Inductive heater Argon atmosphere heat treating oven Just for a start of course. On the other hand..a decent horizontal milling machine and the proper cutter, with a good dividing head would do the job. But you would still need the argon heat treating oven. But you could do it with less power Now a furnace and an extruder...not sure what that would require... Gunner "jusme" wrote in message ... Hi, members. I need ~T-10 Torx bit material that runs more than the conventional 3/8" down the length. I really need 2 or 3 feet or more lengths. I can't seem to find this anywhere. If it doesn't exist, does anyone have any suggestions on how to make it? I may need 50 pieces at a time. Thanks j/b "Pax Americana is a philosophy. Hardly an empire. Making sure other people play nice and dont kill each other (and us) off in job lots is hardly empire building, particularly when you give them self determination under "play nice" rules. Think of it as having your older brother knock the **** out of you for torturing the cat." Gunner |
#7
Posted to rec.crafts.metalworking
|
|||
|
|||
Unique Need for Torx/Star bits.
MM,
I have an indexing head and a bench grinder. I can't answer the rest. HOWSUMEVER, I think I have just thought of an answer to my problem. I was trying to roll my own to save money but in reality, I can buy the pieces but there will be a waste. Just as a learning experience, can you just give me an idea of what you have in mind WITHOUT going to a lot of trouble? Thanks for your response below. j/b "Mechanical Magic" wrote in message ... On Dec 28, 11:10 am, "jusme" wrote: Doesn't anyone have any information on how to make such an item? Is it so obvious that I am overlooking it? Thanks j/b "jusme" wrote in message ... Hi, members. I need ~T-10 Torx bit material that runs more than the conventional 3/8" down the length. I really need 2 or 3 feet or more lengths. I can't seem to find this anywhere. If it doesn't exist, does anyone have any suggestions on how to make it? I may need 50 pieces at a time. Thanks j/b Before I go to a lot of trouble, a few questions. Do you have an indexing head? Cutter grinder? What tolerances do you require? Material? What stresses will be applied? Any other specifications that need to be met? Dave |
#8
Posted to rec.crafts.metalworking
|
|||
|
|||
Unique Need for Torx/Star bits.
Gunner,
I just replied to MM that I had found another way. Just as a learning exercise, why couldn't one chuck up a thin cutter in a vert. mill, and cut a slot length-wise, index the stock and do the same until all sides finished? That must be fraught with Murphies but I have to ask to learn or try it to learn. Thanks for enlightening me on how hard it is. j/b "Gunner Asch" wrote in message ... On Fri, 28 Dec 2007 13:10:16 -0600, "jusme" wrote: Doesn't anyone have any information on how to make such an item? Is it so obvious that I am overlooking it? Thanks j/b Wellll...first thing you need is a nice 150 ton cold header or 50 ton hot header....... 400 amps of 480 3ph Inductive heater Argon atmosphere heat treating oven Just for a start of course. On the other hand..a decent horizontal milling machine and the proper cutter, with a good dividing head would do the job. But you would still need the argon heat treating oven. But you could do it with less power Now a furnace and an extruder...not sure what that would require... Gunner "jusme" wrote in message ... Hi, members. I need ~T-10 Torx bit material that runs more than the conventional 3/8" down the length. I really need 2 or 3 feet or more lengths. I can't seem to find this anywhere. If it doesn't exist, does anyone have any suggestions on how to make it? I may need 50 pieces at a time. Thanks j/b "Pax Americana is a philosophy. Hardly an empire. Making sure other people play nice and dont kill each other (and us) off in job lots is hardly empire building, particularly when you give them self determination under "play nice" rules. Think of it as having your older brother knock the **** out of you for torturing the cat." Gunner |
#9
Posted to rec.crafts.metalworking
|
|||
|
|||
Unique Need for Torx/Star bits.
On Fri, 28 Dec 2007 15:54:01 -0600, "jusme" wrote:
I need ~T-10 Torx bit material that runs more than the conventional 3/8" down the length. I really need 2 or 3 feet or more lengths. I can't seem to find this anywhere. If it doesn't exist, does anyone have any suggestions on how to make it? Do you really need a Torx profile? What about pinion wire? http://www.bostongear.com/products/open/pinion.html# -- Ned Simmons |
#10
Posted to rec.crafts.metalworking
|
|||
|
|||
Unique Need for Torx/Star bits.
j/b,
First, a Torx head is composed of two radiuses. I'll call one the Root, and for a T10, that's about .020" radius. The other is the Tip, and I don't know what that radius is, but for argument lets say its the same as the Root. There is no flat surface anywhere, it's a blended radius, from one to the other. Also called a hexalobular. If you use a slot cutter, and make straight edges, there will be very high stresses at the Tip of your part, which will be resting on the radiused section of the female receiver. Unless you use hardened tool steel, it will deform, or wear very fast. You could have a cutter made, but to find the exact shape you need to buy a copy of ISO 10664, that provides the proper dimensions. (~$150) Dave On Dec 28, 1:59 pm, "jusme" wrote: Gunner, I just replied to MM that I had found another way. Just as a learning exercise, why couldn't one chuck up a thin cutter in a vert. mill, and cut a slot length-wise, index the stock and do the same until all sides finished? That must be fraught with Murphies but I have to ask to learn or try it to learn. Thanks for enlightening me on how hard it is. j/b"Gunner Asch" wrote in message |
#11
Posted to rec.crafts.metalworking
|
|||
|
|||
Unique Need for Torx/Star bits.
On Fri, 28 Dec 2007 15:59:25 -0600, "jusme" wrote:
Gunner, I just replied to MM that I had found another way. Just as a learning exercise, why couldn't one chuck up a thin cutter in a vert. mill, and cut a slot length-wise, index the stock and do the same until all sides finished? Indeed you can. However you asked for the specific profile of a Torx #10 spline. Now if you were simply needing some sort of splined shaft to turn something, a piece of hex stock works nicely, as does a simple square bar. Its easier to make the mate with square stock. It all depends on your torque loading and length. Or if you simply need a really long Torx #10 screw driver..braze/silver solder/Tig a bit on the end of a shaft. That must be fraught with Murphies but I have to ask to learn or try it to learn. Thanks for enlightening me on how hard it is. Its quite easy..if you have the right tools G j/b "Gunner Asch" wrote in message .. . On Fri, 28 Dec 2007 13:10:16 -0600, "jusme" wrote: Doesn't anyone have any information on how to make such an item? Is it so obvious that I am overlooking it? Thanks j/b Wellll...first thing you need is a nice 150 ton cold header or 50 ton hot header....... 400 amps of 480 3ph Inductive heater Argon atmosphere heat treating oven Just for a start of course. On the other hand..a decent horizontal milling machine and the proper cutter, with a good dividing head would do the job. But you would still need the argon heat treating oven. But you could do it with less power Now a furnace and an extruder...not sure what that would require... Gunner "jusme" wrote in message ... Hi, members. I need ~T-10 Torx bit material that runs more than the conventional 3/8" down the length. I really need 2 or 3 feet or more lengths. I can't seem to find this anywhere. If it doesn't exist, does anyone have any suggestions on how to make it? I may need 50 pieces at a time. Thanks j/b "Pax Americana is a philosophy. Hardly an empire. Making sure other people play nice and dont kill each other (and us) off in job lots is hardly empire building, particularly when you give them self determination under "play nice" rules. Think of it as having your older brother knock the **** out of you for torturing the cat." Gunner "Pax Americana is a philosophy. Hardly an empire. Making sure other people play nice and dont kill each other (and us) off in job lots is hardly empire building, particularly when you give them self determination under "play nice" rules. Think of it as having your older brother knock the **** out of you for torturing the cat." Gunner |
#12
Posted to rec.crafts.metalworking
|
|||
|
|||
Unique Need for Torx/Star bits.
Ned, that is an excellent idea, especially their stem pinions. Now, if the
d.p. is compatible with the size Torx bit and the price is right, it may be a winner. Thank you much. j/b "Ned Simmons" wrote in message ... On Fri, 28 Dec 2007 15:54:01 -0600, "jusme" wrote: I need ~T-10 Torx bit material that runs more than the conventional 3/8" down the length. I really need 2 or 3 feet or more lengths. I can't seem to find this anywhere. If it doesn't exist, does anyone have any suggestions on how to make it? Do you really need a Torx profile? What about pinion wire? http://www.bostongear.com/products/open/pinion.html# -- Ned Simmons |
#13
Posted to rec.crafts.metalworking
|
|||
|
|||
Unique Need for Torx/Star bits.
I understand, Dave - I think.
Well, if it would last to turn 10 screws, that would be great. Thanks for the info. Could one 'dress' a cutter to yield 'blended' radii? j/b "Mechanical Magic" wrote in message ... j/b, First, a Torx head is composed of two radiuses. I'll call one the Root, and for a T10, that's about .020" radius. The other is the Tip, and I don't know what that radius is, but for argument lets say its the same as the Root. There is no flat surface anywhere, it's a blended radius, from one to the other. Also called a hexalobular. If you use a slot cutter, and make straight edges, there will be very high stresses at the Tip of your part, which will be resting on the radiused section of the female receiver. Unless you use hardened tool steel, it will deform, or wear very fast. You could have a cutter made, but to find the exact shape you need to buy a copy of ISO 10664, that provides the proper dimensions. (~$150) Dave On Dec 28, 1:59 pm, "jusme" wrote: Gunner, I just replied to MM that I had found another way. Just as a learning exercise, why couldn't one chuck up a thin cutter in a vert. mill, and cut a slot length-wise, index the stock and do the same until all sides finished? That must be fraught with Murphies but I have to ask to learn or try it to learn. Thanks for enlightening me on how hard it is. j/b"Gunner Asch" wrote in message |
#14
Posted to rec.crafts.metalworking
|
|||
|
|||
Unique Need for Torx/Star bits.
Gunner,
I only need to turn some Torx head screws. I need to turn ten of the screws per each tool. Maybe, I can use hexagonal or square stock, as you suggest. Every suggestion gets me to thinking and I learn that way. Thanks for the food for thought. j/b "Gunner Asch" wrote in message ... On Fri, 28 Dec 2007 15:59:25 -0600, "jusme" wrote: Gunner, I just replied to MM that I had found another way. Just as a learning exercise, why couldn't one chuck up a thin cutter in a vert. mill, and cut a slot length-wise, index the stock and do the same until all sides finished? Indeed you can. However you asked for the specific profile of a Torx #10 spline. Now if you were simply needing some sort of splined shaft to turn something, a piece of hex stock works nicely, as does a simple square bar. Its easier to make the mate with square stock. It all depends on your torque loading and length. Or if you simply need a really long Torx #10 screw driver..braze/silver solder/Tig a bit on the end of a shaft. That must be fraught with Murphies but I have to ask to learn or try it to learn. Thanks for enlightening me on how hard it is. Its quite easy..if you have the right tools G j/b "Gunner Asch" wrote in message . .. On Fri, 28 Dec 2007 13:10:16 -0600, "jusme" wrote: Doesn't anyone have any information on how to make such an item? Is it so obvious that I am overlooking it? Thanks j/b Wellll...first thing you need is a nice 150 ton cold header or 50 ton hot header....... 400 amps of 480 3ph Inductive heater Argon atmosphere heat treating oven Just for a start of course. On the other hand..a decent horizontal milling machine and the proper cutter, with a good dividing head would do the job. But you would still need the argon heat treating oven. But you could do it with less power Now a furnace and an extruder...not sure what that would require... Gunner "jusme" wrote in message ... Hi, members. I need ~T-10 Torx bit material that runs more than the conventional 3/8" down the length. I really need 2 or 3 feet or more lengths. I can't seem to find this anywhere. If it doesn't exist, does anyone have any suggestions on how to make it? I may need 50 pieces at a time. Thanks j/b "Pax Americana is a philosophy. Hardly an empire. Making sure other people play nice and dont kill each other (and us) off in job lots is hardly empire building, particularly when you give them self determination under "play nice" rules. Think of it as having your older brother knock the **** out of you for torturing the cat." Gunner "Pax Americana is a philosophy. Hardly an empire. Making sure other people play nice and dont kill each other (and us) off in job lots is hardly empire building, particularly when you give them self determination under "play nice" rules. Think of it as having your older brother knock the **** out of you for torturing the cat." Gunner |
#15
Posted to rec.crafts.metalworking
|
|||
|
|||
Unique Need for Torx/Star bits.
On Fri, 28 Dec 2007 19:01:35 -0600, with neither quill nor qualm,
"jusme" quickly quoth: Gunner, I only need to turn some Torx head screws. I need to turn ten of the screws per each tool. Maybe, I can use hexagonal or square stock, as you suggest. Every suggestion gets me to thinking and I learn that way. Thanks for the food for thought. j/b How about buying some standard length Torx bits and solder/braze/welding them to extensions the length you need? -- Once we believe in ourselves, we can risk curiosity, wonder, spontaneous delight, or any experience that reveals the human spirit. --e e cummings |
#16
Posted to rec.crafts.metalworking
|
|||
|
|||
Unique Need for Torx/Star bits.
3/8" steel rod as long as needed.
Drill for a cross pin, like a "T" handle. Insert cross pin, epoxy, or use a spring pin. Drill other end 1/4" then 17/64" about 3/4" deep. Then 9/32" about 1/4" deep, this is to align for the following. In a scrap block, drill 3/16" hole. Insert T10 bit in hole. (The kind that's about 1" long overall, meant to fit in a hex holder.) Place rod from above over the hex, and "cold form" the hex into the end of the rod. (Hit it with a hammer.) Dave On Dec 28, 5:06 pm, Larry Jaques wrote: On Fri, 28 Dec 2007 19:01:35 -0600, with neither quill nor qualm, "jusme" quickly quoth: Gunner, I only need to turn some Torx head screws. I need to turn ten of the screws per each tool. Maybe, I can use hexagonal or square stock, as you suggest. Every suggestion gets me to thinking and I learn that way. Thanks for the food for thought. j/b How about buying some standard length Torx bits and solder/braze/welding them to extensions the length you need? -- Once we believe in ourselves, we can risk curiosity, wonder, spontaneous delight, or any experience that reveals the human spirit. --e e cummings |
#17
Posted to rec.crafts.metalworking
|
|||
|
|||
Unique Need for Torx/Star bits.
jusme wrote: Gunner, I only need to turn some Torx head screws. I need to turn ten of the screws per each tool. Maybe, I can use hexagonal or square stock, as you suggest. Every suggestion gets me to thinking and I learn that way. Thanks for the food for thought. j/b You can buy a Torx bit & socket with a 1/4" or 3/8" drive and use as many extensions as you need. |
#18
Posted to rec.crafts.metalworking
|
|||
|
|||
Unique Need for Torx/Star bits.
Larry, that was the epiphany that I had earlier. I was just trying to save
money instead of buying 50 to 100 bits. I don't need to extend them, I need to saw them off. j/b "Larry Jaques" wrote in message ... On Fri, 28 Dec 2007 19:01:35 -0600, with neither quill nor qualm, "jusme" quickly quoth: Gunner, I only need to turn some Torx head screws. I need to turn ten of the screws per each tool. Maybe, I can use hexagonal or square stock, as you suggest. Every suggestion gets me to thinking and I learn that way. Thanks for the food for thought. j/b How about buying some standard length Torx bits and solder/braze/welding them to extensions the length you need? -- Once we believe in ourselves, we can risk curiosity, wonder, spontaneous delight, or any experience that reveals the human spirit. --e e cummings |
#19
Posted to rec.crafts.metalworking
|
|||
|
|||
Unique Need for Torx/Star bits.
It certainly is a viable option, Dave, but not for my applications.
Thanks for the input. j/b "Mechanical Magic" wrote in message ... 3/8" steel rod as long as needed. Drill for a cross pin, like a "T" handle. Insert cross pin, epoxy, or use a spring pin. Drill other end 1/4" then 17/64" about 3/4" deep. Then 9/32" about 1/4" deep, this is to align for the following. In a scrap block, drill 3/16" hole. Insert T10 bit in hole. (The kind that's about 1" long overall, meant to fit in a hex holder.) Place rod from above over the hex, and "cold form" the hex into the end of the rod. (Hit it with a hammer.) Dave On Dec 28, 5:06 pm, Larry Jaques wrote: On Fri, 28 Dec 2007 19:01:35 -0600, with neither quill nor qualm, "jusme" quickly quoth: Gunner, I only need to turn some Torx head screws. I need to turn ten of the screws per each tool. Maybe, I can use hexagonal or square stock, as you suggest. Every suggestion gets me to thinking and I learn that way. Thanks for the food for thought. j/b How about buying some standard length Torx bits and solder/braze/welding them to extensions the length you need? -- Once we believe in ourselves, we can risk curiosity, wonder, spontaneous delight, or any experience that reveals the human spirit. --e e cummings |
#20
Posted to rec.crafts.metalworking
|
|||
|
|||
Unique Need for Torx/Star bits.
Yes, Ralph, I know this.
However, the applications that I have in mind will be proprietary and that is why I cannot give all of the details. What I really needed before others gave me some different options is simply a long, long rod such as a T-10 Torx bit. Then, I could saw the lengths of bit that I need. I cannot use anything long. I thank you for your reply. j/b "Ralph Henrichs" wrote in message news jusme wrote: Gunner, I only need to turn some Torx head screws. I need to turn ten of the screws per each tool. Maybe, I can use hexagonal or square stock, as you suggest. Every suggestion gets me to thinking and I learn that way. Thanks for the food for thought. j/b You can buy a Torx bit & socket with a 1/4" or 3/8" drive and use as many extensions as you need. |
#21
Posted to rec.crafts.metalworking
|
|||
|
|||
Unique Need for Torx/Star bits.
On 2007-12-29, jusme wrote:
"Ned Simmons" wrote in message ... On Fri, 28 Dec 2007 15:54:01 -0600, "jusme" wrote: I need ~T-10 Torx bit material that runs more than the conventional 3/8" down the length. [ ... ] Do you really need a Torx profile? What about pinion wire? http://www.bostongear.com/products/open/pinion.html# Ned, that is an excellent idea, especially their stem pinions. Now, if the d.p. is compatible with the size Torx bit and the price is right, it may be a winner. You don't need the whole length splined do you? I would suggest that you cut the pinion wire and mount it in a fairly tough 1/4" hex stock. (There are 6" long hex stock with Torx on one end and the detent ring on the other end to give a bit more length. And -- there are 1/4" hex extensions of perhaps eight or nine inches with about a 1/2" diameter socket at the end. If that 1/2" diameter is not too big, you could simply plug several of these in series for a test setup at least. Then recover the socket from the end of these and put it on the longer hex stock (again if the 1/2" diameter of the socket is not a killer). Or, get a bunch of the 6" long torx bits and silver-solder them to longer hex stock. Good Luck, DoN. -- Email: | Voice (all times): (703) 938-4564 (too) near Washington D.C. | http://www.d-and-d.com/dnichols/DoN.html --- Black Holes are where God is dividing by zero --- |
#22
Posted to rec.crafts.metalworking
|
|||
|
|||
Unique Need for Torx/Star bits.
Don, good ideas, all. But, my need is for short Torx bits hence the need
for long Torx stock so that I could saw them for the length I need. Thanks. j/b "DoN. Nichols" wrote in message ... On 2007-12-29, jusme wrote: "Ned Simmons" wrote in message ... On Fri, 28 Dec 2007 15:54:01 -0600, "jusme" wrote: I need ~T-10 Torx bit material that runs more than the conventional 3/8" down the length. [ ... ] Do you really need a Torx profile? What about pinion wire? http://www.bostongear.com/products/open/pinion.html# Ned, that is an excellent idea, especially their stem pinions. Now, if the d.p. is compatible with the size Torx bit and the price is right, it may be a winner. You don't need the whole length splined do you? I would suggest that you cut the pinion wire and mount it in a fairly tough 1/4" hex stock. (There are 6" long hex stock with Torx on one end and the detent ring on the other end to give a bit more length. And -- there are 1/4" hex extensions of perhaps eight or nine inches with about a 1/2" diameter socket at the end. If that 1/2" diameter is not too big, you could simply plug several of these in series for a test setup at least. Then recover the socket from the end of these and put it on the longer hex stock (again if the 1/2" diameter of the socket is not a killer). Or, get a bunch of the 6" long torx bits and silver-solder them to longer hex stock. Good Luck, DoN. -- Email: | Voice (all times): (703) 938-4564 (too) near Washington D.C. | http://www.d-and-d.com/dnichols/DoN.html --- Black Holes are where God is dividing by zero --- |
#23
Posted to rec.crafts.metalworking
|
|||
|
|||
Unique Need for Torx/Star bits.
On Fri, 28 Dec 2007 21:24:12 -0600, with neither quill nor qualm,
"jusme" quickly quoth: Larry, that was the epiphany that I had earlier. I was just trying to save money instead of buying 50 to 100 bits. I don't need to extend them, I need to saw them off. You should be able to get them for a song in that quantity. Why not give McMasters a call and tell them what you need? They might be able to contact the forge who does their bits and can give you precisely what you want for cheap. Here are T25 bits, 50 for $15.73 http://tinyurl.com/3dr846 -- Once we believe in ourselves, we can risk curiosity, wonder, spontaneous delight, or any experience that reveals the human spirit. --e e cummings |
#24
Posted to rec.crafts.metalworking
|
|||
|
|||
Unique Need for Torx/Star bits.
Excellent, Larry. They also have T-10s in quantity.
Thank you! This group is great. j/b "Larry Jaques" wrote in message ... On Fri, 28 Dec 2007 21:24:12 -0600, with neither quill nor qualm, "jusme" quickly quoth: Larry, that was the epiphany that I had earlier. I was just trying to save money instead of buying 50 to 100 bits. I don't need to extend them, I need to saw them off. You should be able to get them for a song in that quantity. Why not give McMasters a call and tell them what you need? They might be able to contact the forge who does their bits and can give you precisely what you want for cheap. Here are T25 bits, 50 for $15.73 http://tinyurl.com/3dr846 -- Once we believe in ourselves, we can risk curiosity, wonder, spontaneous delight, or any experience that reveals the human spirit. --e e cummings |
#25
Posted to rec.crafts.metalworking
|
|||
|
|||
Unique Need for Torx/Star bits.
"jusme" wrote:
Hi, members. I need ~T-10 Torx bit material that runs more than the conventional 3/8" down the length. I really need 2 or 3 feet or more lengths. I can't seem to find this anywhere. If it doesn't exist, does anyone have any suggestions on how to make it? I may need 50 pieces at a time. Thanks j/b If I understand correctly, you are trying to make extended length torx bits. If so, just buy some common bits and silver braze to some rod. I drove a bunch of 5" wood screws a few years ago using a bit I extended that way. The braze held just fine. Wes |
#26
Posted to rec.crafts.metalworking
|
|||
|
|||
Unique Need for Torx/Star bits.
Wrong, Wes.
I wanted to make one extremely long Torx bit so that I could saw it into the lengths that I need. Thank you for trying to help. j/b "Wes" wrote in message ... "jusme" wrote: Hi, members. I need ~T-10 Torx bit material that runs more than the conventional 3/8" down the length. I really need 2 or 3 feet or more lengths. I can't seem to find this anywhere. If it doesn't exist, does anyone have any suggestions on how to make it? I may need 50 pieces at a time. Thanks j/b If I understand correctly, you are trying to make extended length torx bits. If so, just buy some common bits and silver braze to some rod. I drove a bunch of 5" wood screws a few years ago using a bit I extended that way. The braze held just fine. Wes |
#27
Posted to rec.crafts.metalworking
|
|||
|
|||
Unique Need for Torx/Star bits.
jusme wrote:
Wrong, Wes. I wanted to make one extremely long Torx bit so that I could saw it into the lengths that I need. Thank you for trying to help. j/b Then, not to put it too succinctly, you might be far better off asking for lengths that you need, rather than a length that is not available, that you intend to cut off anyway. Almost every Torx tip I have seen was built onto the end of otherwise plain rod. Either forged or machined. Dead easy to stick a cut off Torx key onto the end of a rod. Better to state your actual needs, rather than ask for something that like as not, does not readily exist. Cheers Trevor Jones |
#28
Posted to rec.crafts.metalworking
|
|||
|
|||
Unique Need for Torx/Star bits.
On 2007-12-29, jusme wrote:
"Larry Jaques" wrote in message ... [ ... ] How about buying some standard length Torx bits and solder/braze/welding them to extensions the length you need? [ ... ] Larry, that was the epiphany that I had earlier. I was just trying to save money instead of buying 50 to 100 bits. I don't need to extend them, I need to saw them off. Oh! You're expecting it to have the Torx profile the whole length. Typically -- the Torx profile only extends 1/4 inch or so for the larger ones, and less for the smaller ones. It then fairly quickly fans out to a full 1/4" hex. The reason for this is that if you kept it at that tiny diameter for any significant length, the shaft would wind up -- limiting the torque which can be applied to the screw. You would not like the results. This is why there were suggestions to take the pinion wire (if it turned out to have the right profile) and mount short lengths of it in larger diameter stock. Instead -- why not check whether you can get the bits in gross packaging from someplace like MSC -- the price can drop significantly with quantity purchasing. For that matter -- you can get them in the same format as the Allen wrenchs (L shape) and those may well be the least expensive format in gross packages. Good Luck, DoN. -- Email: | Voice (all times): (703) 938-4564 (too) near Washington D.C. | http://www.d-and-d.com/dnichols/DoN.html --- Black Holes are where God is dividing by zero --- |
#29
Posted to rec.crafts.metalworking
|
|||
|
|||
Unique Need for Torx/Star bits.
Thanks, Don.
j/b "DoN. Nichols" wrote in message ... On 2007-12-29, jusme wrote: "Larry Jaques" wrote in message ... [ ... ] How about buying some standard length Torx bits and solder/braze/welding them to extensions the length you need? [ ... ] Larry, that was the epiphany that I had earlier. I was just trying to save money instead of buying 50 to 100 bits. I don't need to extend them, I need to saw them off. Oh! You're expecting it to have the Torx profile the whole length. Typically -- the Torx profile only extends 1/4 inch or so for the larger ones, and less for the smaller ones. It then fairly quickly fans out to a full 1/4" hex. The reason for this is that if you kept it at that tiny diameter for any significant length, the shaft would wind up -- limiting the torque which can be applied to the screw. You would not like the results. This is why there were suggestions to take the pinion wire (if it turned out to have the right profile) and mount short lengths of it in larger diameter stock. Instead -- why not check whether you can get the bits in gross packaging from someplace like MSC -- the price can drop significantly with quantity purchasing. For that matter -- you can get them in the same format as the Allen wrenchs (L shape) and those may well be the least expensive format in gross packages. Good Luck, DoN. -- Email: | Voice (all times): (703) 938-4564 (too) near Washington D.C. | http://www.d-and-d.com/dnichols/DoN.html --- Black Holes are where God is dividing by zero --- |
#30
Posted to rec.crafts.metalworking
|
|||
|
|||
Unique Need for Torx/Star bits.
Trevor, had you read my first post on this issue, you would not have made
your post. j/b "Trevor Jones" wrote in message news:PRwdj.23369$wy2.18926@edtnps90... jusme wrote: Wrong, Wes. I wanted to make one extremely long Torx bit so that I could saw it into the lengths that I need. Thank you for trying to help. j/b Then, not to put it too succinctly, you might be far better off asking for lengths that you need, rather than a length that is not available, that you intend to cut off anyway. Almost every Torx tip I have seen was built onto the end of otherwise plain rod. Either forged or machined. Dead easy to stick a cut off Torx key onto the end of a rod. Better to state your actual needs, rather than ask for something that like as not, does not readily exist. Cheers Trevor Jones |
#31
Posted to rec.crafts.metalworking
|
|||
|
|||
Unique Need for Torx/Star bits.
jusme wrote:
Trevor, had you read my first post on this issue, you would not have made your post. j/b I read the first post. And the subsequent ones. It said you wanted 2-3 foot lenths of Torx bit. Something that is not readilly available, because it is not used for shafting. Then you said, and this is a copy and paste from your post... "But, my need is for short Torx bits hence the need for long Torx stock so that I could saw them for the length I need." And also.. "I only need to turn some Torx head screws. I need to turn ten of the screws per each tool." How long do you need? Overall? This is the issue I had with the whole deal. If you actually out and say what you need in the end, you are far more likely to get useable answers. Thus, my comment. Someone quoted you a resonable price for the stuff that YOU asked for, considering. Considering especially, that you have no idea how to make it, nor much of an idea of the likelihood of success in the endeavor. Then you said that you needed it to be used as a Torx wrench. The implication of this, to me, is that you are using it to turn a Torx head screw. Correct, or no? You need it to reach down a deep hole. How deep? Ask the correct questions, and get useful answers! If you need a long reach Torx driver, they are cheap. If you need a 2 to 3 foot length of Torx profile shafting, they are an expensive custon made item, not cheap. So. Clear enough? You have been beating around the bush, trying to reach an end, by coming up with stuff that has to be custom made, in order to make some cheapass short-term use, throwaway tools that you could likely as not buy in pound boxes. If you would ante up with just a wee bit of useful information, like, for instance, how deep a hole do you have to drive the screw at the bottom of, you would very likely not only get an answer, but likely 3 or 4 links to varoius products available. That's how I am seeing this, in any case. So. Y'all gonna ante up with some specifics, or just continue blundering around the hard way? Cheers Trevor Jones |
#32
Posted to rec.crafts.metalworking
|
|||
|
|||
Unique Need for Torx/Star bits.
Trevor,
Are you having a bad day? I said that I need two to three OR MORE FEET. There is no specific length that I need other that what I specified above this sentence. Make it 8 feet then, as is implied in "OR MORE". You ASSume much without the benefit of fact, only guesses. I do not need to reach down a deep hole. Again, if you had REALLY read all of the posts, you would have discovered that I didn't need a "long-reach" Torx bit. I said what I needed in the very first post. Also, I asked if anyone could give me some ideas on how to make such an item/s. I got many great responses and ideas. I DID NOT ask for a quote, as you seem to think. Close to your last paragraph where you say that I am wanting some cheap-ass tool, you again ASSume that I am trying to drive a screw in a deep hole. Wrong yet again. And no, I am not at liberty to give anymore information, as I stated, which you would have known had you read the entire thread as you claim that you did, when I said it is somewhat proprietary. So, Trevor, rather than "around" and make ASSumptions, why not REALLY read the entire thread before you 'go off'. j/b Oh, and it is not 'we', only me - another ASSumption on your part. Flame away if you so choose but it is better to simply drop the issue "Trevor Jones" wrote in message news:mfNdj.51013$5l3.9620@edtnps82... jusme wrote: Trevor, had you read my first post on this issue, you would not have made your post. j/b I read the first post. And the subsequent ones. It said you wanted 2-3 foot lenths of Torx bit. Something that is not readilly available, because it is not used for shafting. Then you said, and this is a copy and paste from your post... "But, my need is for short Torx bits hence the need for long Torx stock so that I could saw them for the length I need." And also.. "I only need to turn some Torx head screws. I need to turn ten of the screws per each tool." How long do you need? Overall? This is the issue I had with the whole deal. If you actually out and say what you need in the end, you are far more likely to get useable answers. Thus, my comment. Someone quoted you a resonable price for the stuff that YOU asked for, considering. Considering especially, that you have no idea how to make it, nor much of an idea of the likelihood of success in the endeavor. Then you said that you needed it to be used as a Torx wrench. The implication of this, to me, is that you are using it to turn a Torx head screw. Correct, or no? You need it to reach down a deep hole. How deep? Ask the correct questions, and get useful answers! If you need a long reach Torx driver, they are cheap. If you need a 2 to 3 foot length of Torx profile shafting, they are an expensive custon made item, not cheap. So. Clear enough? You have been beating around the bush, trying to reach an end, by coming up with stuff that has to be custom made, in order to make some cheapass short-term use, throwaway tools that you could likely as not buy in pound boxes. If you would ante up with just a wee bit of useful information, like, for instance, how deep a hole do you have to drive the screw at the bottom of, you would very likely not only get an answer, but likely 3 or 4 links to varoius products available. That's how I am seeing this, in any case. So. Y'all gonna ante up with some specifics, or just continue blundering around the hard way? Cheers Trevor Jones |
#33
Posted to rec.crafts.metalworking
|
|||
|
|||
Unique Need for Torx/Star bits.
On Sun, 30 Dec 2007 12:22:07 -0600, with neither quill nor qualm,
"jusme" quickly quoth: Trevor, Are you having a bad day? I said that I need two to three OR MORE FEET. Joe, suffice it to say that half a dozen of us thought you wanted long sections of torx profile arn. That's why you got our replies talking about such. Next time you'll write more clearly, right? --- Stay centered by accepting whatever you are doing. This is the ultimate. --Chuang-tzu (369 BC - 286 BC) |
#34
Posted to rec.crafts.metalworking
|
|||
|
|||
Unique Need for Torx/Star bits.
jusme wrote:
Trevor, Are you having a bad day? I said that I need two to three OR MORE FEET. There is no specific length that I need other that what I specified above this sentence. Make it 8 feet then, as is implied in "OR MORE". You ASSume much without the benefit of fact, only guesses. I do not need to reach down a deep hole. Again, if you had REALLY read all of the posts, you would have discovered that I didn't need a "long-reach" Torx bit. I said what I needed in the very first post. Also, I asked if anyone could give me some ideas on how to make such an item/s. I got many great responses and ideas. I DID NOT ask for a quote, as you seem to think. Close to your last paragraph where you say that I am wanting some cheap-ass tool, you again ASSume that I am trying to drive a screw in a deep hole. Wrong yet again. And no, I am not at liberty to give anymore information, as I stated, which you would have known had you read the entire thread as you claim that you did, when I said it is somewhat proprietary. So, Trevor, rather than "around" and make ASSumptions, why not REALLY read the entire thread before you 'go off'. j/b Thanks for that j/b, it pretty much leaves me feeling vindicated. My conclusion is that you are just another nutbar inventor, too brainlocked on a complicated way of getting to an end, to see that there is a cheap and simple method to reach it. So far, of all the guys I have dealt with that were inventing stuff, you appear to be helping keep my experiences with inventors consistant, anyways. Any one of them would give the average machine shop operator shivers, if they tried to become customers. Headache. Capital H. Good luck with the project. Cheers Trevor Jones |
#35
Posted to rec.crafts.metalworking
|
|||
|
|||
Unique Need for Torx/Star bits.
On Sun, 30 Dec 2007 12:22:07 -0600 in rec.crafts.metalworking,
"jusme" wrote, Trevor, Are you having a bad day? I said that I need two to three OR MORE FEET. There is no specific length that I need other that what I specified above this sentence. Make it 8 feet then, as is implied in "OR MORE". WRONG. You wrote "I really need 2 or 3 feet or more lengths." "Lengths" means you need pieces that length. Which was a lie! Now we find out you need many short driver bits (easy) and not long shaft-like pieces (hard or nonexistent.) Face it, you screwed up, you asked for what you didn't need and didn't say what you needed. |
#36
Posted to rec.crafts.metalworking
|
|||
|
|||
Unique Need for Torx/Star bits.
Larry,
What is an arn.? j/b "Larry Jaques" wrote in message ... On Sun, 30 Dec 2007 12:22:07 -0600, with neither quill nor qualm, "jusme" quickly quoth: Trevor, Are you having a bad day? I said that I need two to three OR MORE FEET. Joe, suffice it to say that half a dozen of us thought you wanted long sections of torx profile arn. That's why you got our replies talking about such. Next time you'll write more clearly, right? --- Stay centered by accepting whatever you are doing. This is the ultimate. --Chuang-tzu (369 BC - 286 BC) |
#37
Posted to rec.crafts.metalworking
|
|||
|
|||
Unique Need for Torx/Star bits.
Jeez,
Are a few of you on medications? If not, perhaps they are in order. If these very few can't decipher plain English and make asinine ASSumptions, then, learn to comprehend what you read. "Rich gifts wax poor when givers prove unkind". Will. S. j/b "David Harmon" wrote in message ... On Sun, 30 Dec 2007 12:22:07 -0600 in rec.crafts.metalworking, "jusme" wrote, Trevor, Are you having a bad day? I said that I need two to three OR MORE FEET. There is no specific length that I need other that what I specified above this sentence. Make it 8 feet then, as is implied in "OR MORE". WRONG. You wrote "I really need 2 or 3 feet or more lengths." "Lengths" means you need pieces that length. Which was a lie! Now we find out you need many short driver bits (easy) and not long shaft-like pieces (hard or nonexistent.) Face it, you screwed up, you asked for what you didn't need and didn't say what you needed. |
#38
Posted to rec.crafts.metalworking
|
|||
|
|||
Unique Need for Torx/Star bits.
TJ.
Please tell me the 'cheap and simple method' to reach my goal. j/b "Trevor Jones" wrote in message news:RDTdj.51100$5l3.47421@edtnps82... jusme wrote: Trevor, Are you having a bad day? I said that I need two to three OR MORE FEET. There is no specific length that I need other that what I specified above this sentence. Make it 8 feet then, as is implied in "OR MORE". You ASSume much without the benefit of fact, only guesses. I do not need to reach down a deep hole. Again, if you had REALLY read all of the posts, you would have discovered that I didn't need a "long-reach" Torx bit. I said what I needed in the very first post. Also, I asked if anyone could give me some ideas on how to make such an item/s. I got many great responses and ideas. I DID NOT ask for a quote, as you seem to think. Close to your last paragraph where you say that I am wanting some cheap-ass tool, you again ASSume that I am trying to drive a screw in a deep hole. Wrong yet again. And no, I am not at liberty to give anymore information, as I stated, which you would have known had you read the entire thread as you claim that you did, when I said it is somewhat proprietary. So, Trevor, rather than "around" and make ASSumptions, why not REALLY read the entire thread before you 'go off'. j/b Thanks for that j/b, it pretty much leaves me feeling vindicated. My conclusion is that you are just another nutbar inventor, too brainlocked on a complicated way of getting to an end, to see that there is a cheap and simple method to reach it. So far, of all the guys I have dealt with that were inventing stuff, you appear to be helping keep my experiences with inventors consistant, anyways. Any one of them would give the average machine shop operator shivers, if they tried to become customers. Headache. Capital H. Good luck with the project. Cheers Trevor Jones |
#39
Posted to rec.crafts.metalworking
|
|||
|
|||
Unique Need for Torx/Star bits.
You know, David, if you really feel that way, I am going to go to bed
tonight and cry myself to sleep. I do not wish to upset your very delicate balance but, I did say exactly what I wanted and asked about how to produce such. Many fine members here gave me some great suggestions and just reading them spurred me to think of other options. I find the world fascinating and particularly the Internet where one meets all KINDS. j/b "David Harmon" wrote in message ... On Sun, 30 Dec 2007 12:22:07 -0600 in rec.crafts.metalworking, "jusme" wrote, Trevor, Are you having a bad day? I said that I need two to three OR MORE FEET. There is no specific length that I need other that what I specified above this sentence. Make it 8 feet then, as is implied in "OR MORE". WRONG. You wrote "I really need 2 or 3 feet or more lengths." "Lengths" means you need pieces that length. Which was a lie! Now we find out you need many short driver bits (easy) and not long shaft-like pieces (hard or nonexistent.) Face it, you screwed up, you asked for what you didn't need and didn't say what you needed. |
#40
Posted to rec.crafts.metalworking
|
|||
|
|||
Unique Need for Torx/Star bits.
On Sun, 30 Dec 2007 21:56:38 -0600, jusme wrote:
Jeez, Are a few of you on medications? If not, perhaps they are in order. Just so you know, implying that those who respond to you are mentally ill is rarely a way to encourage more people to try to help you. If these very few can't decipher plain English and make asinine ASSumptions, then, learn to comprehend what you read. plonk |
Reply |
|
Thread Tools | Search this Thread |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Forum | |||
TENNIS STAR SANIYA MIRZA CAUGHT ON CAM IN A FIVE STAR HOTEL INHYDREABAD | Woodworking | |||
TENNIS STAR SANIYA MIRZA CAUGHT ON CAM IN A FIVE STAR HOTEL INHYDREABAD | Home Repair | |||
Check this out! Unique item on EBAY. Only 2.50 - Star Wars Tv Adverts, 284 page 1984 Argos Catalogue on CDR | Woodworking | |||
Where to find Torx screwdrivers, not bits? | Home Repair | |||
Torx 25 hex bits in bulk... | Metalworking |