Home |
Search |
Today's Posts |
|
Home Repair (alt.home.repair) For all homeowners and DIYers with many experienced tradesmen. Solve your toughest home fix-it problems. |
Reply |
|
|
LinkBack | Thread Tools | Display Modes |
#1
Posted to alt.building.construction,alt.home.repair
|
|||
|
|||
cutting 6 x 6 beams with miter saw ???
Will a 12 inch, non-reciprocating miter saw cut 6 x 6 beams in one
pass ??? I know it would be close, but I would like to hear from someone who has done it. Again, can it cut in one pass, so as to get a perfectly smooth cut ? Thanks !! James |
#2
Posted to alt.building.construction,alt.home.repair
|
|||
|
|||
cutting 6 x 6 beams with miter saw ???
On May 6, 10:47*am, "James" wrote:
Will a *12 inch, *non-reciprocating miter saw cut *6 *x 6 * beams in one pass ??? * *I know it would be close, but I would like to hear from someone who has done it. *Again, can it cut in one pass, so as to get a perfectly smooth cut ? Thanks !! James It's going to depend on the saw. I would doubt it for most of them. It's not that difficult to get a decent cut in two passes if the saw is set up square. I can get pretty durn close with a hand circular saw if I take my time. Besides you're working with a 6x6 which is by no means going to be perfect in any other direction. |
#3
Posted to alt.building.construction,alt.home.repair
|
|||
|
|||
cutting 6 x 6 beams with miter saw ???
In article ,
"James" wrote: Will a 12 inch, non-reciprocating miter saw cut 6 x 6 beams in one pass ??? I know it would be close, but I would like to hear from someone who has done it. Again, can it cut in one pass, so as to get a perfectly smooth cut ? Thanks !! James I've not heard the term "non-reciprocating." Does that mean it's a circular saw? If so, unless the hub diameter is 0.000", it isn't going to cut something half the diameter of the blade. |
#4
Posted to alt.building.construction,alt.home.repair
|
|||
|
|||
cutting 6 x 6 beams with miter saw ???
On May 6, 10:47*am, "James" wrote:
Will a *12 inch, *non-reciprocating miter saw cut *6 *x 6 * beams in one pass ??? * *I know it would be close, but I would like to hear from someone who has done it. *Again, can it cut in one pass, so as to get a perfectly smooth cut ? No. First off, a miter saw does not reciprocate, it rotates, and no saw provides a perfectly smooth cut unless you have a rather loose definition of perfectly. Make a miter box out of some scrap plywood and use a plain old vanilla hand saw, and clean it up with a sharp hand plane. It won't kill you, you won't mess up the beam, and it's good exercise. R |
#5
Posted to alt.building.construction,alt.home.repair
|
|||
|
|||
cutting 6 x 6 beams with miter saw ???
On May 6, 11:06*am, Smitty Two wrote:
In article , *"James" wrote: Will a *12 inch, *non-reciprocating miter saw cut *6 *x 6 * beams in one pass ??? * *I know it would be close, but I would like to hear from someone who has done it. *Again, can it cut in one pass, so as to get a perfectly smooth cut ? Thanks !! James I've not heard the term "non-reciprocating." Does that mean it's a circular saw? If so, unless the hub diameter is 0.000", it isn't going to cut something half the diameter of the blade. That's true but a 6x6 is not 6x6 either. |
#6
Posted to alt.building.construction,alt.home.repair
|
|||
|
|||
cutting 6 x 6 beams with miter saw ???
On 5/6/2011 9:47 AM, James wrote:
Will a 12 inch, non-reciprocating miter saw cut 6 x 6 beams in one pass ??? I know it would be close, but I would like to hear from someone who has done it. Again, can it cut in one pass, so as to get a perfectly smooth cut ? Thanks !! James I can't imagine how ANY 12" blade would cut a 5 1/2 or 6" cut. If you have a washer holding the blade on, the very MOST you could ever get is 5 1/2" and that is if you could cut all the way to the washer and that's not likely. -- Steve Barker remove the "not" from my address to email |
#7
Posted to alt.building.construction,alt.home.repair
|
|||
|
|||
cutting 6 x 6 beams with miter saw ???
On May 6, 10:47*am, "James" wrote:
Will a *12 inch, *non-reciprocating miter saw cut *6 *x 6 * beams in one pass ??? * *I know it would be close, but I would like to hear from someone who has done it. *Again, can it cut in one pass, so as to get a perfectly smooth cut ? Thanks !! James Do you mean a non-sliding miter saw? I've never heard of a reciprocating miter saw, so I'm pretty confident in stating that *all* miter saws are non-reciprocating. In fact, a reciprocating miter saw sounds really scary! Besides, you'd be amazed at what a belt sander can do to clean up any ridges left from a cut made from multiple sides. |
#8
Posted to alt.building.construction,alt.home.repair
|
|||
|
|||
cutting 6 x 6 beams with miter saw ???
Thanks for the nice replies.... I made a mistake in using the word
non-reciprocating... I meant non-sliding.... one chap caught that.... What is the next size, after 12 inch ? Does it go to 14, or larger ? BTW, will be cutting dozens of 6 x 6 beams, so could cut down on work if we had a saw that can cut in one pass. Am building outside steps on a slope, in the mountains. Will build "squares" out of beams, and stake them in the ground with rebar. Will nail beam squares together wtih 10 inch galvanized spiral nails. For the project, it will require a lot of drilling. Thinking about buying a basic drill press to drill pilot holes first. James |
#9
Posted to alt.building.construction,alt.home.repair
|
|||
|
|||
cutting 6 x 6 beams with miter saw ???
On May 6, 3:33*pm, "James" wrote:
Thanks for the nice replies.... I made a mistake in using the word non-reciprocating... I meant non-sliding.... *one chap caught that.... What is the next size, after 12 *inch ? * * Does it go to *14, or larger ? BTW, will be cutting dozens of 6 x 6 *beams, so could cut down on work if we had a saw that can cut in one pass. Am building outside steps on a slope, in the mountains. *Will build "squares" *out of beams, and stake them in the ground with rebar. *Will nail beam squares together wtih 10 inch galvanized spiral nails. *For the project, it will require a lot of drilling. Thinking about buying a basic drill press to drill pilot holes first. James If you building stairs out of them then the cut quality is not that important. Use a chain saw. |
#10
Posted to alt.building.construction,alt.home.repair
|
|||
|
|||
cutting 6 x 6 beams with miter saw ???
On May 6, 7:47*am, "James" wrote:
Will a *12 inch, *non-reciprocating miter saw cut *6 *x 6 * beams in one pass ??? * *I know it would be close, but I would like to hear from someone who has done it. *Again, can it cut in one pass, so as to get a perfectly smooth cut ? Thanks !! James Do a Google search on 12" miter saws. There has a to be a tool review or tool comparison for 12" miter saw. My experience with a limited number of 12 inchers says that you'll need to jump to a 14" miter saw to make that cut in a single pass. Otherwise use a beam saw or a hand saw in a miter box. cheers Non |
#11
Posted to alt.building.construction,alt.home.repair
|
|||
|
|||
cutting 6 x 6 beams with miter saw ???
jamesgangnc wrote in
: On May 6, 3:33*pm, "James" wrote: Thanks for the nice replies.... I made a mistake in using the word non-reciprocating... I meant non-sliding.... *one chap caught that.... What is the next size, after 12 *inch ? * * Does it go to *14, or larger ? BTW, will be cutting dozens of 6 x 6 *beams, so could cut down on work if we had a saw that can cut in one pass. Am building outside steps on a slope, in the mountains. *Will build "squares" *out of beams, and stake them in the ground with rebar. *Wi ll nail beam squares together wtih 10 inch galvanized spiral nails. *For the project, it will require a lot of drilling. Thinking about buying a basic drill press to drill pilot holes first. James If you building stairs out of them then the cut quality is not that important. Use a chain saw. Bingo! Even a cheap electric one. |
#12
Posted to alt.building.construction,alt.home.repair
|
|||
|
|||
cutting 6 x 6 beams with miter saw ???
On May 6, 3:33*pm, "James" wrote:
Thanks for the nice replies.... I made a mistake in using the word non-reciprocating... I meant non-sliding.... *one chap caught that.... What is the next size, after 12 *inch ? * * Does it go to *14, or larger ? BTW, will be cutting dozens of 6 x 6 *beams, so could cut down on work if we had a saw that can cut in one pass. Am building outside steps on a slope, in the mountains. *Will build "squares" *out of beams, and stake them in the ground with rebar. *Will nail beam squares together wtih 10 inch galvanized spiral nails. *For the project, it will require a lot of drilling. Thinking about buying a basic drill press to drill pilot holes first. James Are you sure 10 inch nails are long enough? You might want to consider re-bar. Probably cheaper and can be cut to lengths that can go through multiple beams and into the ground. |
#13
Posted to alt.building.construction,alt.home.repair
|
|||
|
|||
cutting 6 x 6 beams with miter saw ???
On May 6, 10:47*am, "James" wrote:
Will a *12 inch, *non-reciprocating miter saw cut *6 *x 6 * beams in one pass ??? * *I know it would be close, but I would like to hear from someone who has done it. *Again, can it cut in one pass, so as to get a perfectly smooth cut ? Thanks !! James Did that not too long ago for clothes line and mailbox post.. I just used my circular saw and a speed square as a saw guide. This didnt cut all the way through but finishing with a hand saw was a piece of cake. Probably could have done the same with my chop saw. BTW my nephew was with me and I was trying to show him how to use the speed square as a guide...he has some coordination problems and was having trouble holding both the saw and the square so I had him clamp the square in place. Jimmie |
#14
Posted to alt.building.construction,alt.home.repair
|
|||
|
|||
cutting 6 x 6 beams with miter saw ???
The diameter of the motor is one limiting factor. To the OP,
we strongly doubt it. -- Christopher A. Young Learn more about Jesus www.lds.org .. "Steve Barker" wrote in message ... I can't imagine how ANY 12" blade would cut a 5 1/2 or 6" cut. If you have a washer holding the blade on, the very MOST you could ever get is 5 1/2" and that is if you could cut all the way to the washer and that's not likely. -- Steve Barker remove the "not" from my address to email |
#15
Posted to alt.building.construction,alt.home.repair
|
|||
|
|||
cutting 6 x 6 beams with miter saw ???
Next to your drill press, please consider a band saw.
http://www.harborfreight.com/14-inch...saw-67595.html Please also consider "nail gun", not sure pneumatic is what you want. Power nailer, maybe? One that shoots .22 rimfire blanks loads. Cuts down on the sore elbows from endless pounding. -- Christopher A. Young Learn more about Jesus www.lds.org .. "James" wrote in message net... Thanks for the nice replies.... I made a mistake in using the word non-reciprocating... I meant non-sliding.... one chap caught that.... What is the next size, after 12 inch ? Does it go to 14, or larger ? BTW, will be cutting dozens of 6 x 6 beams, so could cut down on work if we had a saw that can cut in one pass. Am building outside steps on a slope, in the mountains. Will build "squares" out of beams, and stake them in the ground with rebar. Will nail beam squares together wtih 10 inch galvanized spiral nails. For the project, it will require a lot of drilling. Thinking about buying a basic drill press to drill pilot holes first. James |
#16
Posted to alt.building.construction,alt.home.repair
|
|||
|
|||
cutting 6 x 6 beams with miter saw ???
And, a Lucky Strike is not a smoke?
Not that I'd know; I've never had any urge to light one of those foul smelling things, and put chemicals in my body and die of cancer. Having spent all my money on nicotine addiction. -- Christopher A. Young Learn more about Jesus www.lds.org .. "jamesgangnc" wrote in message ... I've not heard the term "non-reciprocating." Does that mean it's a circular saw? If so, unless the hub diameter is 0.000", it isn't going to cut something half the diameter of the blade. That's true but a 6x6 is not 6x6 either. |
#17
Posted to alt.building.construction,alt.home.repair
|
|||
|
|||
cutting 6 x 6 beams with miter saw ???
Nearly guarantees tennis elbow.
-- Christopher A. Young Learn more about Jesus www.lds.org .. "DD_BobK" wrote in message ... Otherwise use a beam saw or a hand saw in a miter box. cheers Non |
#18
Posted to alt.building.construction,alt.home.repair
|
|||
|
|||
cutting 6 x 6 beams with miter saw ???
On May 6, 5:21*pm, "Stormin Mormon"
wrote: And, a Lucky Strike is not a smoke? Not that I'd know; I've never had any urge to light one of those foul smelling things, and put chemicals in my body and die of cancer. Having spent all my money on nicotine addiction. -- Christopher A. Young Learn more about Jesus *www.lds.org . "jamesgangnc" wrote in message ... I've not heard the term "non-reciprocating." Does that mean it's a circular saw? If so, unless the hub diameter is 0.000", it isn't going to cut something half the diameter of the blade. That's true but a 6x6 is not 6x6 either. If it was a choice between top posting and you smoking, I think you'd get a lot of votes for you smoking. R |
#19
Posted to alt.building.construction,alt.home.repair
|
|||
|
|||
cutting 6 x 6 beams with miter saw ???
Ok, see your points now Oren, thanks !!
James |
#20
Posted to alt.building.construction,alt.home.repair
|
|||
|
|||
cutting 6 x 6 beams with miter saw ???
Stormin Mormon wrote the following:
And, a Lucky Strike is not a smoke? Not that I'd know; I've never had any urge to light one of those foul smelling things, and put chemicals in my body and die of cancer. Having spent all my money on nicotine addiction. ....and all this has to do with cutting a 6x6 beam with a 12" miter saw how? -- Bill In Hamptonburgh, NY In the original Orange County. Est. 1683 To email, remove the double zeroes after @ |
#21
Posted to alt.building.construction,alt.home.repair
|
|||
|
|||
cutting 6 x 6 beams with miter saw ???
On May 6, 8:08*pm, willshak wrote:
Stormin Mormon wrote the following: And, a Lucky Strike is not a smoke? Not that I'd know; I've never had any urge to light one of those foul smelling things, and put chemicals in my body and die of cancer. Having spent all my money on nicotine addiction. ...and all this has to do with cutting a 6x6 beam with a 12" miter saw how? -- Bill In Hamptonburgh, NY In the original Orange County. Est. 1683 To email, remove the double zeroes after @ Inasmuch as the audience is getting pretty fed up with his anti usenet custom... Harry K |
#22
Posted to alt.building.construction,alt.home.repair
|
|||
|
|||
cutting 6 x 6 beams with miter saw ???
On May 6, 12:33*pm, "James" wrote:
Thanks for the nice replies.... I made a mistake in using the word non-reciprocating... I meant non-sliding.... *one chap caught that.... What is the next size, after 12 *inch ? * * Does it go to *14, or larger ? BTW, will be cutting dozens of 6 x 6 *beams, so could cut down on work if we had a saw that can cut in one pass. Am building outside steps on a slope, in the mountains. *Will build "squares" *out of beams, and stake them in the ground with rebar. *Will nail beam squares together wtih 10 inch galvanized spiral nails. *For the project, it will require a lot of drilling. Thinking about buying a basic drill press to drill pilot holes first. James If that is the use, you are way overengineering it. That is not a "finish" type cut - use a chainsaw. Harry K |
#23
Posted to alt.building.construction,alt.home.repair
|
|||
|
|||
cutting 6 x 6 beams with miter saw ???
On May 6, 12:33*pm, "James" wrote:
Thanks for the nice replies.... I made a mistake in using the word non-reciprocating... I meant non-sliding.... *one chap caught that.... What is the next size, after 12 *inch ? * * Does it go to *14, or larger ? BTW, will be cutting dozens of 6 x 6 *beams, so could cut down on work if we had a saw that can cut in one pass. Am building outside steps on a slope, in the mountains. *Will build "squares" *out of beams, and stake them in the ground with rebar. *Will nail beam squares together wtih 10 inch galvanized spiral nails. *For the project, it will require a lot of drilling. Thinking about buying a basic drill press to drill pilot holes first. James I forgot the second part - drilling the hole. Again, drill press accuracy is not required. A 3/8 or 1/2' drill and "speed bore" spade dills are the route to go. I've BTDT. Harry K |
#24
Posted to alt.building.construction,alt.home.repair
|
|||
|
|||
cutting 6 x 6 beams with miter saw ???
Harry, I will not use a chainsaw, because as I said, I have seen steps cut
with a chainsaw and I don't like the look. Perhaps most folks would, but I don't, and my project will look better when it is completed. And, the purpose of the drill press has nothing to do with drill accuracy... it has to do with speed and manpower. I have MANY steps thurs many holes to drill for these steps.... I think that drilling perhaps 400-500 holes ten inches deep, would justify "considering" a drill press. James |
#25
Posted to alt.building.construction,alt.home.repair
|
|||
|
|||
cutting 6 x 6 beams with miter saw ???
You mean it's not obvious?
-- Christopher A. Young Learn more about Jesus www.lds.org .. "willshak" wrote in message m... Stormin Mormon wrote the following: And, a Lucky Strike is not a smoke? Not that I'd know; I've never had any urge to light one of those foul smelling things, and put chemicals in my body and die of cancer. Having spent all my money on nicotine addiction. ....and all this has to do with cutting a 6x6 beam with a 12" miter saw how? -- Bill In Hamptonburgh, NY In the original Orange County. Est. 1683 To email, remove the double zeroes after @ |
#26
Posted to alt.building.construction,alt.home.repair
|
|||
|
|||
cutting 6 x 6 beams with miter saw ???
James, I am not aware of any drill press capable of 10" quill
stroke. I think you will definitely be in the portable drill market. The big decision will be whether to work with a ship auger or speed bores with extension. You might consider using a reciprocating saw for the timber cuts if you do not find a chainsaw acceptable. -- ~~~~~~~~~~~~~~~~~~~~ DanG Keep the whole world singing . . . "James" wrote in message net... Harry, I will not use a chainsaw, because as I said, I have seen steps cut with a chainsaw and I don't like the look. Perhaps most folks would, but I don't, and my project will look better when it is completed. And, the purpose of the drill press has nothing to do with drill accuracy... it has to do with speed and manpower. I have MANY steps thurs many holes to drill for these steps.... I think that drilling perhaps 400-500 holes ten inches deep, would justify "considering" a drill press. James |
#27
Posted to alt.building.construction,alt.home.repair
|
|||
|
|||
cutting 6 x 6 beams with miter saw ???
In article , "DanG"
wrote: James, I am not aware of any drill press capable of 10" quill stroke. Good point, although theoretically he could drill them all halfway, then move the table. I still don't quite understand what he's doing. |
#28
Posted to alt.building.construction,alt.home.repair
|
|||
|
|||
cutting 6 x 6 beams with miter saw ???
On May 7, 6:25*am, "James" wrote:
Harry, I will not use a chainsaw, because as I said, I have seen steps cut with a chainsaw and I don't like the look. *Perhaps most folks would, but I don't, and my project will look better when it is completed. And, the purpose of the drill press has nothing to do with drill accuracy.... it has to do with speed and manpower. * I have MANY steps thurs many holes to drill for these steps.... * *I think that drilling perhaps 400-500 holes ten inches deep, would justify "considering" a drill press. James What you need is a Milwaukee Hole Hawg and a ship auger of the appropriate size. Unfortunately, Milwaukee self feed bits don't come is the smaller sizes you need. Look over the bits and such in the section of plumbers and electricians specialties at your box store. Joe |
#29
Posted to alt.building.construction,alt.home.repair
|
|||
|
|||
cutting 6 x 6 beams with miter saw ???
On 5/7/2011 8:53 AM, DanG wrote:
James, I am not aware of any drill press capable of 10" quill stroke. I think you will definitely be in the portable drill market. The big decision will be whether to work with a ship auger or speed bores with extension. You might consider using a reciprocating saw for the timber cuts if you do not find a chainsaw acceptable. Agreed. He is making this WAY more complicated than it needs to be. Even if he had a giant chop saw and wide-mouth drill press, I suspect that after hoisting and supporting the first half-dozen timbers to cut and drill them, he would be looking for another solution. An electrician's drill with and auger or long spade bit, and a small chainsaw, is what we used back in the stone age. A speed square and an old screwdriver, to scribe the cut lines, helps. Fit one end, mark the other end, shove a brick under it to keep the blade out of the dirt, and cut. Once timber is in place, drill the slightly undersize hole through the first timber into the second, and pound in the rebar peg with a BFH. Only time we did fancy smooth cuts and used threaded rod or bolts, was for the pretty stuff up on the deck, which wasn't made from landscape timbers. Yes, a Sawzall or clone would work and produce a prettier cut, but it would be a lot slower than a chainsaw. (The framing crews decking out the roofs on the apartments I worked on as a kid, used a chainsaw to cut off the wild ends on the decking. 3 stories up, strolling along with no safety harness. Those guys were all young and immortal, but I never saw one fall.) -- aem sends... |
#30
Posted to alt.building.construction,alt.home.repair
|
|||
|
|||
cutting 6 x 6 beams with miter saw ???
On May 7, 7:25*am, "James" wrote:
Harry, I will not use a chainsaw, because as I said, I have seen steps cut with a chainsaw and I don't like the look. *Perhaps most folks would, but I don't, and my project will look better when it is completed. I think you're assuming a couple of things about chainsaws and their use that are affecting your opinion. I have seen tile jobs that sucked - doesn't mean that I think all tile jobs suck. Most people are not looking for joinery-quality cuts when they whip out a chainsaw. They're looking for down and dirty, and probably have a worn chain, so it's no surprise that what you saw was down and dirty - yours doesn't have to be. Invest the money in the correct tool. http://www.timbertools.com/Products/...saw-guide.html or, if you want slower so you can enjoy the experience on the hillside for longer http://www.amazon.com/Makita-5402NA-.../dp/B0000614UR BTW, you are simply kidding yourself about the cut ends of the ties. Unless you're popping for the $ for cedar, you're going to be getting PT 6x6s and they'll have splits, checks, and big knots. Even if your cuts were perfect the whole job would still look like it was made from lumber with splits, checks, and big knots. You're mentally gilding the lily before you start which is a perfect recipe for a big letdown. I advise you to adjust your thinking. And, the purpose of the drill press has nothing to do with drill accuracy.... it has to do with speed and manpower. * I have MANY steps thurs many holes to drill for these steps.... * *I think that drilling perhaps 400-500 holes ten inches deep, would justify "considering" a drill press. Again - you're simply kidding yourself. Lugging a drill press up and down and on top of whatever needs to be drilled is pointless in your application. The ties are drilled in place and you don't need a perfectly perpendicular hole, you need a straight hole that's relatively perpendicular. Any heavy duty D-handled 1/2" drill will do the job. Use an extension for the drill bit so you don't have to bend over to drill the holes. The weight of the drill will feed the bit - you just have to keep it from rotating. I still think you should do it with hand tools. They build moral fiber. R |
#31
Posted to alt.building.construction,alt.home.repair
|
|||
|
|||
cutting 6 x 6 beams with miter saw ???
On 5/7/2011 6:25 AM, James wrote:
Harry, I will not use a chainsaw, because as I said, I have seen steps cut with a chainsaw and I don't like the look. Perhaps most folks would, but I don't, and my project will look better when it is completed. And, the purpose of the drill press has nothing to do with drill accuracy... it has to do with speed and manpower. I have MANY steps thurs many holes to drill for these steps.... I think that drilling perhaps 400-500 holes ten inches deep, would justify "considering" a drill press. James it CERTAINLY won't be faster with a drill press. I'd get an auger bit and a gas powered drill. -- Steve Barker remove the "not" from my address to email |
#32
Posted to alt.building.construction,alt.home.repair
|
|||
|
|||
cutting 6 x 6 beams with miter saw ???
On May 7, 10:29*pm, Steve Barker wrote:
On 5/7/2011 6:25 AM, James wrote: Harry, I will not use a chainsaw, because as I said, I have seen steps cut with a chainsaw and I don't like the look. *Perhaps most folks would, but I don't, and my project will look better when it is completed. And, the purpose of the drill press has nothing to do with drill accuracy... it has to do with speed and manpower. * I have MANY steps thurs many holes to drill for these steps.... * *I think that drilling perhaps 400-500 holes ten inches deep, would justify "considering" a drill press. James it CERTAINLY won't be faster with a drill press. *I'd get an auger bit and a gas powered drill. Probably simpler to just use a generator. I've never seen a gas powered drill, but I imagine they'd be fun to use. R |
#33
Posted to alt.building.construction,alt.home.repair
|
|||
|
|||
cutting 6 x 6 beams with miter saw ???
RicodJour wrote the following:
On May 7, 10:29 pm, Steve Barker wrote: On 5/7/2011 6:25 AM, James wrote: Harry, I will not use a chainsaw, because as I said, I have seen steps cut with a chainsaw and I don't like the look. Perhaps most folks would, but I don't, and my project will look better when it is completed. And, the purpose of the drill press has nothing to do with drill accuracy... it has to do with speed and manpower. I have MANY steps thurs many holes to drill for these steps.... I think that drilling perhaps 400-500 holes ten inches deep, would justify "considering" a drill press. James it CERTAINLY won't be faster with a drill press. I'd get an auger bit and a gas powered drill. Probably simpler to just use a generator. I've never seen a gas powered drill, but I imagine they'd be fun to use. R Why not? George Goble had a gas guitar. :-) (George Gobel was a stand up comedian who had as a prop, a Gibson L5CT acoustic guitar. When someone asked him why he didn't use an electric guitar, he said it was a gas guitar). -- Bill In Hamptonburgh, NY In the original Orange County. Est. 1683 To email, remove the double zeroes after @ |
#34
Posted to alt.building.construction,alt.home.repair
|
|||
|
|||
cutting 6 x 6 beams with miter saw ???
On 5/7/2011 11:22 PM, RicodJour wrote:
On May 7, 10:29 pm, Steve wrote: On 5/7/2011 6:25 AM, James wrote: Harry, I will not use a chainsaw, because as I said, I have seen steps cut with a chainsaw and I don't like the look. Perhaps most folks would, but I don't, and my project will look better when it is completed. And, the purpose of the drill press has nothing to do with drill accuracy... it has to do with speed and manpower. I have MANY steps thurs many holes to drill for these steps.... I think that drilling perhaps 400-500 holes ten inches deep, would justify "considering" a drill press. James it CERTAINLY won't be faster with a drill press. I'd get an auger bit and a gas powered drill. Probably simpler to just use a generator. I've never seen a gas powered drill, but I imagine they'd be fun to use. R we had one at the lawn and landscape joint i spent 13 years at. We put a swing set anchor in it, and the girls drilled holes for flower bulbs with it. Not sure what brand it was. It was red. -- Steve Barker remove the "not" from my address to email |
#35
Posted to alt.building.construction,alt.home.repair
|
|||
|
|||
cutting 6 x 6 beams with miter saw ???
On 5/7/2011 11:22 PM, RicodJour wrote:
On May 7, 10:29 pm, Steve wrote: On 5/7/2011 6:25 AM, James wrote: Harry, I will not use a chainsaw, because as I said, I have seen steps cut with a chainsaw and I don't like the look. Perhaps most folks would, but I don't, and my project will look better when it is completed. And, the purpose of the drill press has nothing to do with drill accuracy... it has to do with speed and manpower. I have MANY steps thurs many holes to drill for these steps.... I think that drilling perhaps 400-500 holes ten inches deep, would justify "considering" a drill press. James it CERTAINLY won't be faster with a drill press. I'd get an auger bit and a gas powered drill. Probably simpler to just use a generator. I've never seen a gas powered drill, but I imagine they'd be fun to use. R http://www.stihlusa.com/construction/augerdrill.html http://tinyurl.com/3dddglb (tanaka) -- Steve Barker remove the "not" from my address to email |
#36
Posted to alt.building.construction,alt.home.repair
|
|||
|
|||
cutting 6 x 6 beams with miter saw ???
James wrote:
Will a 12 inch, non-reciprocating miter saw cut 6 x 6 beams in one pass ??? I know it would be close, but I would like to hear from someone who has done it. Again, can it cut in one pass, so as to get a perfectly smooth cut ? Thanks !! Late to the party, but just saw this today. What you need is a Beam Saw http://www.timberwolftools.com/tools...SXEc400HM.html An interesting collection of power tools for working big lumber, but not cheap -- PV If you can't fix it with a hammer.......you have an electrical problem |
#37
Posted to alt.building.construction,alt.home.repair
|
|||
|
|||
cutting 6 x 6 beams with miter saw ???
On May 6, 3:33*pm, "James" wrote:
Thanks for the nice replies.... I made a mistake in using the word non-reciprocating... I meant non-sliding.... *one chap caught that.... What is the next size, after 12 *inch ? * * Does it go to *14, or larger ? BTW, will be cutting dozens of 6 x 6 *beams, so could cut down on work if we had a saw that can cut in one pass. Am building outside steps on a slope, in the mountains. *Will build "squares" *out of beams, and stake them in the ground with rebar. *Will nail beam squares together wtih 10 inch galvanized spiral nails. *For the project, it will require a lot of drilling. Thinking about buying a basic drill press to drill pilot holes first. James Northern Tool used to have a big chop saw meant to cut metal. You cut probably put a big blade on one of these to cut wood. That would probably be without a guard So make sure children and pets are far away when using. As I remember the saw was less than $100 US last I saw of one. Jimmie |
#38
Posted to alt.building.construction,alt.home.repair
|
|||
|
|||
cutting 6 x 6 beams with miter saw ???
wow, will look at Northern Tool for this chop saw !!
Thanks !! James |
#39
Posted to alt.building.construction,alt.home.repair
|
|||
|
|||
cutting 6 x 6 beams with miter saw ???
On May 8, 6:47*pm, "PV" edrnouser@ spam telus.net wrote:
James wrote: Will a *12 inch, *non-reciprocating miter saw cut *6 *x 6 * beams in one pass ??? * *I know it would be close, but I would like to hear from someone who has done it. *Again, can it cut in one pass, so as to get a perfectly smooth cut ? Thanks !! Late to the party, but just saw this today. *What you need is a Beam Saw http://www.timberwolftools.com/tools...SXEc400HM.html An interesting collection of power tools for working big lumber, but not cheap -- PV If you can't fix it with a hammer.......you have an electrical problem Those won't work for the OP. He has stated in no uncertain terms that he won't use a chainsaw. Since those beam cutters are nothing more (said with jest) than electric chain saws, he won't be using one of those. He's made up his mind. Don't go confusing him with facts. |
#40
Posted to alt.building.construction,alt.home.repair
|
|||
|
|||
cutting 6 x 6 beams with miter saw ???
On May 8, 7:40*pm, "James" wrote:
wow, will look at Northern Tool for this chop saw !! Thanks !! James As far as I know, the largest chop saw Northern Tool sells is 14". As far as I know, the max cut size with a 14" chop saw is 5" for square stock. |
Reply |
|
Thread Tools | Search this Thread |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Forum | |||
Miter cutting | Woodworking | |||
Cutting Aluminum with Miter Saw???? | Woodworking | |||
Cutting metal with a compound miter saw | Home Repair | |||
I-Beams T-Beams and cutting? | Metalworking | |||
cutting compound miter staves | Woodturning |