Home |
Search |
Today's Posts |
|
UK diy (uk.d-i-y) For the discussion of all topics related to diy (do-it-yourself) in the UK. All levels of experience and proficency are welcome to join in to ask questions or offer solutions. |
Reply |
|
LinkBack | Thread Tools | Display Modes |
#1
Posted to uk.d-i-y
|
|||
|
|||
Worktop mason's mitre jigs
Why do these jigs specify a minimum worktop width?
I need to join a couple of bullnose bathroom worktops at right angles; they're about 200mm deep which seems to be smaller than any of the jigs can handle - any suggestions on how to do it? I wondered about using the aluminium corner joint strips but can't find anything for a 14mm bull nose. Dave |
#2
Posted to uk.d-i-y
|
|||
|
|||
Worktop mason's mitre jigs
NoSpam wrote:
Why do these jigs specify a minimum worktop width? I need to join a couple of bullnose bathroom worktops at right angles; they're about 200mm deep which seems to be smaller than any of the jigs can handle - any suggestions on how to do it? I wondered about using the aluminium corner joint strips but can't find anything for a 14mm bull nose. Dave Poor form to answer myself, but having just found a manual on the Trend site the answer is blindingly obvious - it's just down to where the guide holes are drilled. I presume all I need to do is ignore the pre-drilled guide bush locations and align the jig to suit the depth of the worktop. Dave |
#3
Posted to uk.d-i-y
|
|||
|
|||
Worktop mason's mitre jigs
NoSpam wrote:
Why do these jigs specify a minimum worktop width? I need to join a couple of bullnose bathroom worktops at right angles; they're about 200mm deep which seems to be smaller than any of the jigs can handle - any suggestions on how to do it? I wondered about using the aluminium corner joint strips but can't find anything for a 14mm bull nose. They usually have predrilled holes that you stick locating pegs through to help hold the jig in place. The holes are located for "standard" worktop depths[1]. You can probably still use one to do what you want, but will need to resort to careful clamping of the jig instead. [1] Recalls time when helping a mate finish off his kitchen, I made the mistake of asking him if the the worktops were standard 600mm ones rather than measuring them. Yes says he. Only after a test fitting where the front edge of the returning bit of worktop fell short of the mitre cut in the other bit by a couple of inches, did he remember that he had cut that bit down in depth a little bit! (at this point we decided that perhaps continuing the oak edging we were going to put round the butler sink cutout, right round all of the worktop would be a good idea). -- Cheers, John. /================================================== ===============\ | Internode Ltd - http://www.internode.co.uk | |-----------------------------------------------------------------| | John Rumm - john(at)internode(dot)co(dot)uk | \================================================= ================/ |
#4
Posted to uk.d-i-y
|
|||
|
|||
Worktop mason's mitre jigs
On Sun, 14 Jan 2007 14:10:12 +0000, NoSpam wrote:
Why do these jigs specify a minimum worktop width? I need to join a couple of bullnose bathroom worktops at right angles; they're about 200mm deep which seems to be smaller than any of the jigs can handle - any suggestions on how to do it? I wondered about using the aluminium corner joint strips but can't find anything for a 14mm bull nose. Given that the depth is only 200mm you won't waste a lot of worktop by cutting a straight 45 degree line. You should be able to use the jig to set that up by just using clamps. -- Ed Sirett - Property maintainer and registered gas fitter. The FAQ for uk.diy is at http://www.diyfaq.org.uk Gas fitting FAQ http://www.makewrite.demon.co.uk/GasFitting.html Sealed CH FAQ http://www.makewrite.demon.co.uk/SealedCH.html Choosing a Boiler FAQ http://www.makewrite.demon.co.uk/BoilerChoice.html Gas Fitting Standards Docs he http://www.makewrite.demon.co.uk/GasFittingStandards |
#5
Posted to uk.d-i-y
|
|||
|
|||
Worktop mason's mitre jigs
Ed Sirett wrote:
On Sun, 14 Jan 2007 14:10:12 +0000, NoSpam wrote: Why do these jigs specify a minimum worktop width? I need to join a couple of bullnose bathroom worktops at right angles; they're about 200mm deep which seems to be smaller than any of the jigs can handle - any suggestions on how to do it? I wondered about using the aluminium corner joint strips but can't find anything for a 14mm bull nose. Given that the depth is only 200mm you won't waste a lot of worktop by cutting a straight 45 degree line. You should be able to use the jig to set that up by just using clamps. Thanks Ed. I did wonder about doing that but I need to make one of the lengths removable (cistern access), so the idea was to use some dowels rather than glue and connectors - easier to do with a mason's mitre than with a 45 degree joint (also, I've already cut them roughly to length :-) ) Dave |
#6
Posted to uk.d-i-y
|
|||
|
|||
Worktop mason's mitre jigs
On Mon, 15 Jan 2007 22:14:12 +0000, NoSpam wrote:
Ed Sirett wrote: On Sun, 14 Jan 2007 14:10:12 +0000, NoSpam wrote: Why do these jigs specify a minimum worktop width? I need to join a couple of bullnose bathroom worktops at right angles; they're about 200mm deep which seems to be smaller than any of the jigs can handle - any suggestions on how to do it? I wondered about using the aluminium corner joint strips but can't find anything for a 14mm bull nose. Given that the depth is only 200mm you won't waste a lot of worktop by cutting a straight 45 degree line. You should be able to use the jig to set that up by just using clamps. Thanks Ed. I did wonder about doing that but I need to make one of the lengths removable (cistern access), so the idea was to use some dowels rather than glue and connectors - easier to do with a mason's mitre than with a 45 degree joint (also, I've already cut them roughly to length :-) ) Dave I would have though that the jig would get two pegs in contact but you'll have to make your own assessment of the angle. -- Ed Sirett - Property maintainer and registered gas fitter. The FAQ for uk.diy is at http://www.diyfaq.org.uk Gas fitting FAQ http://www.makewrite.demon.co.uk/GasFitting.html Sealed CH FAQ http://www.makewrite.demon.co.uk/SealedCH.html Choosing a Boiler FAQ http://www.makewrite.demon.co.uk/BoilerChoice.html Gas Fitting Standards Docs he http://www.makewrite.demon.co.uk/GasFittingStandards |
Reply |
Thread Tools | Search this Thread |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Forum | |||
Mitre square edge worktop? | UK diy | |||
Mitre of kitchen worktop anyone?? | UK diy | |||
Worktop jigs and radii | UK diy | |||
Kitchen worktop jigs | UK diy | |||
Routers & Worktop Jigs | UK diy |