Home |
Search |
Today's Posts |
|
Metalworking (rec.crafts.metalworking) Discuss various aspects of working with metal, such as machining, welding, metal joining, screwing, casting, hardening/tempering, blacksmithing/forging, spinning and hammer work, sheet metal work. |
Reply |
|
LinkBack | Thread Tools | Display Modes |
#1
|
|||
|
|||
Myford Super 7: $10,000???
On Fri, 12 Sep 2003 09:58:40 -0700, "Mark Winlund"
wrote: "Doug Warner" wrote Are these lathes THAT much better than the typical $2000 Taiwan-made units? No. Mark Not that much better, but at least twice as good. Saw one go at auction in Fergus Ontario area a few weeks ago for $2800 Canadian - sold new in 1992, and virtually unused. If I didn't already have an older one at home in the garage he would not have gotten it so cheap. Paid $1500 Canadian for mine about 5 years ago and figure I got a bargain. |
#2
|
|||
|
|||
Myford Super 7: $10,000???
On Fri, 12 Sep 2003 12:05:01 -0400, Doug Warner
wrote: Curious to see what it would cost to replace my old, beat-up ML-7 with the latest Super 7 model, I called Blue Ridge Machinery, and got a quote of "$9900, $10,500" I was too shocked to ask what the two different prices were for.. Are these lathes THAT much better than the typical $2000 Taiwan-made units? If you wait 50 years and pick one up second hand, the price will probably be quite reasonable. Mark Rand (my ML7 is now 52 :-) RTFM |
#3
|
|||
|
|||
Myford Super 7: $10,000???
On Fri, 12 Sep 2003 12:05:01 -0400, Doug Warner
wrote: Curious to see what it would cost to replace my old, beat-up ML-7 with the latest Super 7 model, I called Blue Ridge Machinery, and got a quote of "$9900, $10,500" I was too shocked to ask what the two different prices were for.. Are these lathes THAT much better than the typical $2000 Taiwan-made units? To reply, please remove one letter from each side of "@" Spammers are vermin. Please kill them. That's almost a 50% increase in price since I bought my Super 7 long-bed in 1999. Is the price quoted for the new version with the much larger spindle through hole, or the long-produced model? (I can't recall the precise sizes, but it's close to 5/8" whilst the new one is well over 1") That change might account for a large part of the price increase. I'm glad I bought mine, but if the price were $10K, I'm not sure I would have reached for the checkbook so quickly. Jack |
#4
|
|||
|
|||
Myford Super 7: $10,000???
I bought mine in the early 70's for $1035 with 3 and 4 jaw chucks!
Still like new with lots of hours on it, save for a few paint chips. My favorite, over my SBL 9" too. RichD On Fri, 12 Sep 2003 19:59:42 -0400, Jack Smith wrote: On Fri, 12 Sep 2003 12:05:01 -0400, Doug Warner wrote: Curious to see what it would cost to replace my old, beat-up ML-7 with the latest Super 7 model, I called Blue Ridge Machinery, and got a quote of "$9900, $10,500" I was too shocked to ask what the two different prices were for.. Are these lathes THAT much better than the typical $2000 Taiwan-made units? To reply, please remove one letter from each side of "@" Spammers are vermin. Please kill them. That's almost a 50% increase in price since I bought my Super 7 long-bed in 1999. Is the price quoted for the new version with the much larger spindle through hole, or the long-produced model? (I can't recall the precise sizes, but it's close to 5/8" whilst the new one is well over 1") That change might account for a large part of the price increase. I'm glad I bought mine, but if the price were $10K, I'm not sure I would have reached for the checkbook so quickly. Jack |
#5
|
|||
|
|||
Myford Super 7: $10,000???
Think your self lucky
Myford lathes start at $16,000 Australia "Gunner" wrote in message ... On Fri, 12 Sep 2003 19:59:42 -0400, Jack Smith wrote: On Fri, 12 Sep 2003 12:05:01 -0400, Doug Warner wrote: Curious to see what it would cost to replace my old, beat-up ML-7 with the latest Super 7 model, I called Blue Ridge Machinery, and got a quote of "$9900, $10,500" I was too shocked to ask what the two different prices were for.. Are these lathes THAT much better than the typical $2000 Taiwan-made units? To reply, please remove one letter from each side of "@" Spammers are vermin. Please kill them. That's almost a 50% increase in price since I bought my Super 7 long-bed in 1999. Is the price quoted for the new version with the much larger spindle through hole, or the long-produced model? (I can't recall the precise sizes, but it's close to 5/8" whilst the new one is well over 1") That change might account for a large part of the price increase. I'm glad I bought mine, but if the price were $10K, I'm not sure I would have reached for the checkbook so quickly. Jack For a lot less than $10,000 US OR CND, one can purchase a decent Hardinge HLV-H toolroom lathe, used. Even off Ebay. There is a bit of difference between the two lathes...just a bit....G Hell. for half that, a guy can buy a nice used Mori-Seki manual lathe, with a 14" swing. Serious difference between that and a Myford...VBG Gunner Gunner "At the core of liberalism is the spoiled child - miserable, as all spoiled children are, unsatisfied, demanding, ill-disciplined, despotic and useless. Liberalism is a philosphy of sniveling brats." -- P.J. O'Rourke |
#6
|
|||
|
|||
Myford Super 7: $10,000???
In article , Abrasha says...
but I don't think that someone who is looking to replace a Myford Super 7 is in the market for a Hardinge ... Anyone who would turn down an HLVH in favor of a myford is certifiable. Jim ================================================== please reply to: JRR(zero) at yktvmv (dot) vnet (dot) ibm (dot) com ================================================== |
#7
|
|||
|
|||
Myford Super 7: $10,000???
On Fri, 12 Sep 2003 12:05:01 -0400, Doug Warner
wrote: Curious to see what it would cost to replace my old, beat-up ML-7 with the latest Super 7 model, I called Blue Ridge Machinery, and got a quote of "$9900, $10,500" I was too shocked to ask what the two different prices were for.. Are these lathes THAT much better than the typical $2000 Taiwan-made units? Hell, at that price you could buy a cheap Chinese lathe and hire a master-machinist to turn it into a *really* nice machine by blueprinting it, fixing the compound, etc -- and still have enough change left for a whole summer's worth of beer! That Chinese stuff isn't too bad really. If you're prepared to put in the time to make a few modifications and generally tidy up the rough edges they can perform very well indeed. -- you can contact me via http://aardvark.co.nz/contact/ |
#8
|
|||
|
|||
Myford Super 7: $10,000???
jim rozen wrote:
In article , Abrasha says... but I don't think that someone who is looking to replace a Myford Super 7 is in the market for a Hardinge ... Anyone who would turn down an HLVH in favor of a myford is certifiable. I would. Not because I don't want one, but because I do not have the space for one. And a Myford Super 7 would be a nice replacement for and upgrade from my TOS. Besides, "turning down an HLVH" was not the issue. Shopping for a new Myford Super 7 was. And my point was that people who shop for Myfords do not have Hardinge or 14"' swing lathes in mind. Abrasha http://www.abrasha.com |
#9
|
|||
|
|||
Myford Super 7: $10,000???
On Sun, 14 Sep 2003 05:46:13 GMT, Abrasha wrote:
jim rozen wrote: In article , Abrasha says... but I don't think that someone who is looking to replace a Myford Super 7 is in the market for a Hardinge ... Anyone who would turn down an HLVH in favor of a myford is certifiable. I would. Not because I don't want one, but because I do not have the space for one. And a Myford Super 7 would be a nice replacement for and upgrade from my TOS. Besides, "turning down an HLVH" was not the issue. Shopping for a new Myford Super 7 was. And my point was that people who shop for Myfords do not have Hardinge or 14"' swing lathes in mind. Abrasha http://www.abrasha.com But, perhaps they should have a Hardinge in mind, particularly if you get a superior lathe for much less money. I do not know the dimensions of a Super 7, but a Hardinge HLV-H is only about 5' long and about 34" deep, not a particularly big footprint. And that of course includes the cabinet, which has a decent amount of storage under the right side. They do weigh about 1800 lbs, but hey...thats needed for a stable lathe that will cut in the very very small tenths, all day, every day. The HLV-H has a 9ish inch swing and IIRC, 18" between centers. ACTUAL working room. It might go to 20". Gunner "At the core of liberalism is the spoiled child - miserable, as all spoiled children are, unsatisfied, demanding, ill-disciplined, despotic and useless. Liberalism is a philosphy of sniveling brats." -- P.J. O'Rourke |
#10
|
|||
|
|||
Myford Super 7: $10,000???
In article , Abrasha says...
Anyone who would turn down an HLVH in favor of a myford is certifiable. (jim) I would. Not because I don't want one, but because I do not have the space for one. And a Myford Super 7 would be a nice replacement for and upgrade from my TOS. Hmm. Think some more. The DSM-59 that I bought recently takes up *less* floor space than the 9" SB that I once owned. The key to remember is that they have underneath motor drives, the 9" SB model A is like the Myford IIRC and they use a rear-mounted motor and countershaft. Takes up a *lot* of room. Besides, "turning down an HLVH" was not the issue. Shopping for a new Myford Super 7 was. And my point was that people who shop for Myfords do not have Hardinge or 14"' swing lathes in mind. Maybe. Most folks who are are upgrading do so opportunistically. They wait and watch. You must understand there's a *lot* of machinery being sold right now as manufacturing phases out. Which would you buy, the 9" SB model A, for $800, or the nearly unused Harding DSM-59, for $600? Those are the real numbers, too. Granted the DSM-59 is not in the same class as teh HLVH. But it stacks up favorably to the Myford, at less money. And I bet it takes up less floor space. Jim ================================================== please reply to: JRR(zero) at yktvmv (dot) vnet (dot) ibm (dot) com ================================================== |
#11
|
|||
|
|||
Myford Super 7: $10,000???
In article , Gunner says...
For a lot less than $10,000 US OR CND, one can purchase a decent Hardinge HLV-H toolroom lathe, used. Even off Ebay. There is a bit of difference between the two lathes...just a bit....G As one other data point, right before south bend went out of business, they were selling brand new 10Ls for about $16K, for the toolroom model. (This may be one reason why they went out of business.) But given the differences between the myford and the 10L, the $10K number actually kind of makes sense. Jim ================================================== please reply to: JRR(zero) at yktvmv (dot) vnet (dot) ibm (dot) com ================================================== |
#12
|
|||
|
|||
Myford Super 7: $10,000???
For the cost of a new Myford, you could buy my Colchester Chipmaster
(5"ch*20) and have it fully reconditioned to like new, with a variable speed invertor. It is a primo littl elathe, and not much bigger than teh myford, but a far better machine. Geoff |
#13
|
|||
|
|||
Myford Super 7: $10,000???
DejaVU wrote in message ...
ChrisCrosskey scribed in : "Doug Warner" wrote in message .. . Curious to see what it would cost to replace my old, beat-up ML-7 with the latest Super 7 model, I called Blue Ridge Machinery, and got a quote of "$9900, $10,500" I was too shocked to ask what the two different prices were for.. Are these lathes THAT much better than the typical $2000 Taiwan -made units? I personally think so. My ML7 is 55 years old and still going I second that. 1963 ML7, but I learnt on a Super 7, and lust for a Super 7 Plus Conosseur (-: those 2 prices, lower one for the Super 7 Plus, the higher for the Conoseur (how DO you spell that?) which has a built VFD speed control both have 26mm spindle bore and power cross feed iirc. swarf, steam and wind I'm glad I bought a Super 7B a few weeks ago then. I had been looking for a pristine model for the past 2 years and found one the first week of August. It was purchased 6 years ago and the owner had conservatively put 300 hours on it by his guesstimate. It came with a Toolmex 3 jaw, dividing head attachment, swiveling vertical slide, gear cutter assortment, quick change toolpost, tool assortment, assorted tailstock arbors, cabinet stand, cover, spare belts, etc. All for the great price of $2000. With the exception of a few paint scrapes here and there it truly is like new with nary a speck of rust. It also came with the original shipping and packaging for the lathe and all accessories and included all of the original documentation, receipts, etc. The dimensions are 45 inches overall length, 24 inches deep, 59 inches high at the head where the clutch assembly is, and 50 inches high at the tailstock. This model is 19 inches between centers and has the ..59 inch spindle hole. Why this and not the pristine DV59 I saw from a machine tool dealer? $1500 less and 1000 pounds less weight. I needed a relatively light machine so this is what I bought. This is a great platform to learn on and if I decide on an HLVH over the Porsche Boxster in the future I will still keep the Myford. Regards, David |
#14
|
|||
|
|||
Myford Super 7: $10,000???
In article , david says...
The dimensions are 45 inches overall length, 24 inches deep, 59 inches high at the head where the clutch assembly is, and 50 inches high at the tailstock. This model is 19 inches between centers and has the .59 inch spindle hole. And that right there is the single biggest flaw in the machine IMO. I don't know if it's the Lucas heritage or the lack of central heating in britain, but all their lathes have an undersized hole though the spindle. South bend figured that one out around 1940, and bestowed a 1.375 inch bore on its spindle. Why this and not the pristine DV59 I saw from a machine tool dealer? $1500 less and 1000 pounds less weight. I needed a relatively light machine so this is what I bought. Then you have purchased the best machine for you. Basically it seems like a myford in that flavor is pretty similar to the 9" south bend model A. You were lucky and got one with all the bells and whistles for a great price. I've seen tooling for machines like that fetch prices that dwarf the lathe's cost itself. This is a great platform to learn on and if I decide on an HLVH over the Porsche Boxster in the future I will still keep the Myford. Or, if you feel like it, sell the myford for exactly what you put into it, and use that money to help upgrade. Jim ================================================== please reply to: JRR(zero) at yktvmv (dot) vnet (dot) ibm (dot) com ================================================== |
#15
|
|||
|
|||
Myford Super 7: $10,000???
david wrote:
DejaVU wrote in message ... ChrisCrosskey scribed in : "Doug Warner" wrote in message .. . Curious to see what it would cost to replace my old, beat-up ML-7 with the latest Super 7 model, I called Blue Ridge Machinery, and got a quote of "$9900, $10,500" I was too shocked to ask what the two different prices were for.. Are these lathes THAT much better than the typical $2000 Taiwan -made units? I personally think so. My ML7 is 55 years old and still going I second that. 1963 ML7, but I learnt on a Super 7, and lust for a Super 7 Plus Conosseur (-: those 2 prices, lower one for the Super 7 Plus, the higher for the Conoseur (how DO you spell that?) which has a built VFD speed control both have 26mm spindle bore and power cross feed iirc. swarf, steam and wind I'm glad I bought a Super 7B a few weeks ago then. I had been looking for a pristine model for the past 2 years and found one the first week of August. It was purchased 6 years ago and the owner had conservatively put 300 hours on it by his guesstimate. It came with a Toolmex 3 jaw, dividing head attachment, swiveling vertical slide, gear cutter assortment, quick change toolpost, tool assortment, assorted tailstock arbors, cabinet stand, cover, spare belts, etc. All for the great price of $2000. I'm jealous, very jealous. Abrasha http://www.abrasha.com |
Reply |
Thread Tools | Search this Thread |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Forum | |||
How to sell a Myford ML7? | Metalworking | |||
Myford lathe bed reconditioning in Atlanta. area? | Metalworking |