Woodworking (rec.woodworking) Discussion forum covering all aspects of working with wood. All levels of expertise are encouraged to particiapte.

Reply
 
LinkBack Thread Tools Search this Thread Display Modes
  #1   Report Post  
Posted to rec.woodworking
external usenet poster
 
Posts: 6,035
Default Dripp Press Table , Fence, and Indexing Stop

I just posted pics of this DP table top that I built on a.b.p.w.


  #2   Report Post  
Posted to rec.woodworking
external usenet poster
 
Posts: 6,035
Default Drill Press Table , Fence, and Indexing Stop


"Leon" wrote in message
...
I just posted pics of this DP table top that I built on a.b.p.w.


OK it's isn't a Dripp press. ;~()


  #3   Report Post  
Posted to rec.woodworking
external usenet poster
 
Posts: 2,387
Default Drill Press Table , Fence, and Indexing Stop

Leon wrote:
"Leon" wrote in message
...
I just posted pics of this DP table top that I built on a.b.p.w.


OK it's isn't a Dripp press. ;~()


I should say not - but I won't ;-)

It looks pretty good!

--
Morris Dovey
DeSoto Solar
DeSoto, Iowa USA
http://www.iedu.com/DeSoto/
  #4   Report Post  
Posted to rec.woodworking
external usenet poster
 
Posts: 6,035
Default Drill Press Table , Fence, and Indexing Stop


"Morris Dovey" wrote in message
...
Leon wrote:
"Leon" wrote in message
...
I just posted pics of this DP table top that I built on a.b.p.w.


OK it's isn't a Dripp press. ;~()


I should say not - but I won't ;-)

It looks pretty good!


Thanks Morris although my fingers are illiterate.


  #5   Report Post  
Posted to rec.woodworking
external usenet poster
 
Posts: 2,559
Default Drill Press Table , Fence, and Indexing Stop

"Leon" wrote in
:


"Morris Dovey" wrote in message
...
Leon wrote:
"Leon" wrote in message
...
I just posted pics of this DP table top that I built on a.b.p.w.


OK it's isn't a Dripp press. ;~()


I should say not - but I won't ;-)

It looks pretty good!


Thanks Morris although my fingers are illiterate.




I'm going to have to build one of those dripp press tables myself. I
often need a fence and repeatable holes would be a good thing. :-)

My compliments.

Puckdropper
--
On Usenet, no one can hear you laugh. That's a good thing, though, as
some writers are incorrigible.

To email me directly, send a message to puckdropper (at) fastmail.fm


  #6   Report Post  
Posted to rec.woodworking
external usenet poster
 
Posts: 1,619
Default Dripp Press Table , Fence, and Indexing Stop


"Leon" wrote in message
...
I just posted pics of this DP table top that I built on a.b.p.w.

Looks good. That replaceable wood slot in the center is a good idea. And I
like the movable fence in the T slots. Square is whatever fits the
job/stock on a drill press.

Is that a hold down in the third picture? How do you do holdowns and stops
on this table?



  #7   Report Post  
Posted to rec.woodworking
external usenet poster
 
Posts: 6,035
Default Drill Press Table , Fence, and Indexing Stop


"Puckdropper" puckdropper(at)yahoo(dot)com wrote in message
...


I'm going to have to build one of those dripp press tables myself. I
often need a fence and repeatable holes would be a good thing. :-)

My compliments.


Thank you. If you are interested, the 'very" top pieces are phonelic
covered 14 layer birch plywood. The solid bottom piece is 11 ply birch
plywood. the over all dimensions are 1.5" thick, and 16"x 24". Rockler
has the phonelic panels on sale for $20 for a 32 x 24" sheet. I am sure
plain plywood would work but I wanted something that would not stain and
would remain very flat.




Puckdropper
--
On Usenet, no one can hear you laugh. That's a good thing, though, as
some writers are incorrigible.

To email me directly, send a message to puckdropper (at) fastmail.fm



  #8   Report Post  
Posted to rec.woodworking
external usenet poster
 
Posts: 6,035
Default Dripp Press Table , Fence, and Indexing Stop


"Lee Michaels" wrote in message
...

"Leon" wrote in message
...
I just posted pics of this DP table top that I built on a.b.p.w.

Looks good. That replaceable wood slot in the center is a good idea. And
I like the movable fence in the T slots. Square is whatever fits the
job/stock on a drill press.


Thank you, Square works the same way on a router table fence too. ;~) I
actually have 3 or 4 inch slots under each knob on the fence so that the
fence can be slid left or right that amount and so that the fence can ve
clamped down with one end forward. With one end forward I can drill a hinge
hole on a long door with out rolling the DP out, it normally sets back a
bit behind the tool chest on the left side.


Is that a hold down in the third picture? How do you do holdowns and
stops on this table?



No, no hold downs. I am showing the stop in two positions, fence and table
t-slot. To tell you the truth I have never had any use or need for hold
downs on this DP.


  #9   Report Post  
Posted to rec.woodworking
external usenet poster
 
Posts: 2,559
Default Drill Press Table , Fence, and Indexing Stop

"Leon" wrote in
:



Thank you. If you are interested, the 'very" top pieces are phonelic
covered 14 layer birch plywood. The solid bottom piece is 11 ply
birch plywood. the over all dimensions are 1.5" thick, and 16"x 24".
Rockler has the phonelic panels on sale for $20 for a 32 x 24" sheet.
I am sure plain plywood would work but I wanted something that would
not stain and would remain very flat.


Thanks for the info. I'll try building mine with "hardwood plywood" that
Home Depot occasionally sells (usually Birch). I've got a couple pieces
of it waiting for a project.

(Yet another item on the shop to do list. :-))

Puckdropper
--
On Usenet, no one can hear you laugh. That's a good thing, though, as
some writers are incorrigible.

To email me directly, send a message to puckdropper (at) fastmail.fm
Reply
Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules

Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
ROUTER TABLE INDEXING JIG J T Woodworking 0 February 3rd 06 08:07 PM
Drill press table and fence update Morris Dovey Woodworking 1 January 29th 06 12:01 PM
Drill press table and fence update Morris Dovey Woodworking 5 January 29th 06 04:59 AM
ROUTER TABLE INDEXING JIG J T Woodworking 0 November 28th 04 06:32 AM
indexing jig for table saw Troy Hall Woodworking 1 November 20th 04 05:03 AM


All times are GMT +1. The time now is 11:30 AM.

Powered by vBulletin® Copyright ©2000 - 2023, Jelsoft Enterprises Ltd.
Copyright 2004-2023 DIYbanter.
The comments are property of their posters.
 

About Us

"It's about DIY & home improvement"