Woodworking (rec.woodworking) Discussion forum covering all aspects of working with wood. All levels of expertise are encouraged to particiapte.

Reply
 
LinkBack Thread Tools Search this Thread Display Modes
  #1   Report Post  
Troy Hall
 
Posts: n/a
Default indexing jig for table saw

Well my cd case is going well except I snaffued badly! I need to cut dado's
5 5/16" apart on the bottom of the panels. So from my point of view I'm
blind to the cut. I missed by 5/16" by measuring carefully against the
miter gauge track. Theres got to be a better way. The panels are 32" x
37". The first dado goes 3/16" from then end which has a rabbet in it. And
then each successive dado is 5/16" wide by 3/16" deep by 32" long. I
thought about using the cross cut sled, but its setup for the small guide
pieces that seperate the cd's. I thought about originally dadoing the sides
to accept the cd's also, but I couldn't think of an easy way to make an
indexing jig. This would solve both problems hopefully.
you guys have been so helpful so far, I hope you can help with this too. I
can't use a miter gauge index jig because the panels are far longer then the
clearance between the end of the table saw and the blade.

signature Troy & Michelle Hall Cogy Farm Clay Center, Kansas 67432


---
Outgoing mail is certified Virus Free.
Checked by AVG anti-virus system (http://www.grisoft.com).
Version: 6.0.797 / Virus Database: 541 - Release Date: 11/15/2004


  #2   Report Post  
garyhuff
 
Posts: n/a
Default

I do this often with good results. I cut with the fence to the left of
the blade (for reference) but either side will work.
set The fence for the first cut (3/16" in your case). Make the cut
against the fence same as always. Turn off the saw, return the panel to
the original position with the blade in the kerf. Clamp the panel to the
table top to prevent it from slipping around. Now loosen the fence slide
it away from the panel. insert a strip of wood the width of your desired
cut, move the fence right pinning the strip against the panel and lock
the fence. Remove the strip, slide the panel against the fence and make
your next cut. Repeat as necessary.
If you plan carefully you can start with the center cut, do cuts for
half the board , turn it 180 degrees and do the other half, that way the
distance from the blade to the cut is always shorter that the cut to the
end of the panel, a much more balanced way to handle wide cuts. Good luck!

Troy Hall wrote:

Well my cd case is going well except I snaffued badly! I need to cut dado's
5 5/16" apart on the bottom of the panels. So from my point of view I'm
blind to the cut. I missed by 5/16" by measuring carefully against the
miter gauge track. Theres got to be a better way. The panels are 32" x
37". The first dado goes 3/16" from then end which has a rabbet in it. And
then each successive dado is 5/16" wide by 3/16" deep by 32" long. I
thought about using the cross cut sled, but its setup for the small guide
pieces that seperate the cd's. I thought about originally dadoing the sides
to accept the cd's also, but I couldn't think of an easy way to make an
indexing jig. This would solve both problems hopefully.
you guys have been so helpful so far, I hope you can help with this too. I
can't use a miter gauge index jig because the panels are far longer then the
clearance between the end of the table saw and the blade.

signature Troy & Michelle Hall Cogy Farm Clay Center, Kansas 67432


---
Outgoing mail is certified Virus Free.
Checked by AVG anti-virus system (http://www.grisoft.com).
Version: 6.0.797 / Virus Database: 541 - Release Date: 11/15/2004



Reply
Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules

Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
Indexing quill head on mill/drill Robert Scibienski Metalworking 11 June 18th 04 08:31 PM


All times are GMT +1. The time now is 09:21 AM.

Powered by vBulletin® Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004-2024 DIYbanter.
The comments are property of their posters.
 

About Us

"It's about DIY & home improvement"