Home |
Search |
Today's Posts |
|
Woodworking (rec.woodworking) Discussion forum covering all aspects of working with wood. All levels of expertise are encouraged to particiapte. |
Reply |
|
LinkBack | Thread Tools | Display Modes |
#1
Posted to rec.woodworking
|
|||
|
|||
Woodslicer band blades from Highland Hardware
Wow, first resaw of a 2x10 pine board for practice is darn near close
enough to sand out the finish. I'm impressed |
#2
Posted to rec.woodworking
|
|||
|
|||
Woodslicer band blades from Highland Hardware
"Knothead" wrote in message ... Wow, first resaw of a 2x10 pine board for practice is darn near close enough to sand out the finish. I'm impressed If darn near close, what will you use before sanding? |
#3
Posted to rec.woodworking
|
|||
|
|||
Woodslicer band blades from Highland Hardware
Single finish pass in the planer to size it. I could run it through the
Woodmaster with the sanding drum installed but it's set up to mold already so to the planer it goes.... I have the original Jet 18" bandsaw before they figured out that the column needed extensive beefing up. Been running Timberwolf blades since I bought it thinking the low tension was the solution. With this blade I think I might actually not turn this saw into a mailbox post.. |
#4
Posted to rec.woodworking
|
|||
|
|||
Woodslicer band blades from Highland Hardware
"Knothead" wrote in message ... Single finish pass in the planer to size it. I could run it through the Woodmaster with the sanding drum installed but it's set up to mold already so to the planer it goes.... I have the original Jet 18" bandsaw before they figured out that the column needed extensive beefing up. Been running Timberwolf blades since I bought it thinking the low tension was the solution. With this blade I think I might actually not turn this saw into a mailbox post.. Do you run your veneer through the planer on a sled or modified table? I want to get into veneering and cutting my own. I am currently shopping the bigger European model band saws. |
#5
Posted to rec.woodworking
|
|||
|
|||
Woodslicer band blades from Highland Hardware
Knothead wrote:
Wow, first resaw of a 2x10 pine board for practice is darn near close enough to sand out the finish. I'm impressed Thanks for the info... How do you compare it to the Timberwolf blade (I see you've used both)? er -- email not valid |
#6
Posted to rec.woodworking
|
|||
|
|||
Woodslicer band blades from Highland Hardware
I've used both and the WS puts the TW to shame.
-Steve "Enoch Root" wrote in message ... Knothead wrote: Wow, first resaw of a 2x10 pine board for practice is darn near close enough to sand out the finish. I'm impressed Thanks for the info... How do you compare it to the Timberwolf blade (I see you've used both)? er -- email not valid |
#7
Posted to rec.woodworking
|
|||
|
|||
Woodslicer band blades from Highland Hardware
Living in Canada, I thought getting the Wood slicer from Highland,
would be to much $$ for the smoother cut. When the Loonie hit about $0.85, I took the leap, and was rewarded with a smooth cut , it blew my mind. So much for the TW. Still I wish there was a Canadian source. |
#8
Posted to rec.woodworking
|
|||
|
|||
Woodslicer band blades from Highland Hardware
My woodslicer is also much smoother than the timberwolf. BUT the TW is
about 2x as fast on my bandsaw. If one is cutting veneer, or real close to final thickness the woodslicer is the way to go. For my workbench out of dunage, the TW was much quicker. Now, I left the Woodslicer under tension, which I also do to the TW, and it broke a ways from the weld. A local sharpening shop re-welded it, but I have not yet reinstalled into my bandsaw. Alan |
#9
Posted to rec.woodworking
|
|||
|
|||
Woodslicer band blades from Highland Hardware
"arw01" wrote in message oups.com... My woodslicer is also much smoother than the timberwolf. BUT the TW is about 2x as fast on my bandsaw. If one is cutting veneer, or real close to final thickness the woodslicer is the way to go. For my workbench out of dunage, the TW was much quicker. Now, I left the Woodslicer under tension, which I also do to the TW, and it broke a ways from the weld. A local sharpening shop re-welded it, but I have not yet reinstalled into my bandsaw. Alan Do you have any experience with the Laguna Resaw King? |
#10
Posted to rec.woodworking
|
|||
|
|||
Woodslicer band blades from Highland Hardware
I,ve used the woodslicer for re-sawing, it works really good for me. Smooth
cuts n the saw isn,t working hard. I use 1/4" Timber Wolf for my general bandsaw cutting, fast n works good, better than the 3/8" Sears blade i had been using. I have 14" Powermatic bandsaw, n keep the tension off when not in use. Only bad thing now is, my dog "snowball" passed on; he was 14-1/2 yrs....American Eskimo, minature(17#) he used to carry my scraps around n play in the shop....good dog....will miss him... George... "Leon" wrote in message om... "arw01" wrote in message oups.com... My woodslicer is also much smoother than the timberwolf. BUT the TW is about 2x as fast on my bandsaw. If one is cutting veneer, or real close to final thickness the woodslicer is the way to go. For my workbench out of dunage, the TW was much quicker. Now, I left the Woodslicer under tension, which I also do to the TW, and it broke a ways from the weld. A local sharpening shop re-welded it, but I have not yet reinstalled into my bandsaw. Alan Do you have any experience with the Laguna Resaw King? |
#11
Posted to rec.woodworking
|
|||
|
|||
Woodslicer band blades from Highland Hardware
Do you run your veneer through the planer on a sled or modified table? I
want to get into veneering and cutting my own. I am currently shopping the bigger European model band saws. Sorry for the delay. (I now have a spanking new dsl gateway) At this point on a sled but I'm not getting the best results. I was thinking about building an adjustable table and have been filtering through other folks plans on the 'net to see what will works well. |
#12
Posted to rec.woodworking
|
|||
|
|||
Woodslicer band blades from Highland Hardware
The Timberwolves last a long time but the alternating tooth pattern on the
Woodslicer wins hands down on several points. 1. Super quiet 2. Hardly any chateer or resulting marks 3. Thinner and seems to run cooler. 4. Higher tension seems to be better suited for the saw I have. Jets first relaease of this 18' was still in the "beta" stages apparently when I bought it. |
#13
Posted to rec.woodworking
|
|||
|
|||
Woodslicer band blades from Highland Hardware
Sorry to hear about loosing the shop help. I keep two for that reason. The
loss isn't so great. |
#14
Posted to rec.woodworking
|
|||
|
|||
Woodslicer band blades from Highland Hardware
No experience with that blade, they likely don't make em short enough
for my uit. It will take a 2" wide blade, but getting someone to make a 72 7/16" blade is a bit trickier. http://alan.firebin.net/bs50n.html |
#15
Posted to rec.woodworking
|
|||
|
|||
Woodslicer band blades from Highland Hardware
They will make them any size you want... you wil have to wait a while
though. "arw01" wrote in message oups.com... No experience with that blade, they likely don't make em short enough for my uit. It will take a 2" wide blade, but getting someone to make a 72 7/16" blade is a bit trickier. http://alan.firebin.net/bs50n.html |
#16
Posted to rec.woodworking
|
|||
|
|||
Woodslicer band blades from Highland Hardware
3
"Leon" wrote in message . net... "Knothead" wrote in message ... Sorry to hear about loosing the shop help. I keep two for that reason. The loss isn't so great. Not so great but then there are two of you crying over the loss. |
#17
Posted to rec.woodworking
|
|||
|
|||
Woodslicer band blades from Highland Hardware
Knothead wrote:
The Timberwolves last a long time but the alternating tooth pattern on the Woodslicer wins hands down on several points. 1. Super quiet 2. Hardly any chateer or resulting marks 3. Thinner and seems to run cooler. 4. Higher tension seems to be better suited for the saw I have. Jets first relaease of this 18' was still in the "beta" stages apparently when I bought it. Thanks. Is that the regular blade or the "resaw" blade? er -- email not valid |
#18
Posted to rec.woodworking
|
|||
|
|||
Woodslicer band blades from Highland Hardware
C&S wrote: They will make them any size you want... you wil have to wait a while though. They wider blades also get thicker, and thicker is not good on the smaller wheels of the Ryobi bs50n. When I researched buying this bandsaw used, it was noted they tended to break the wider blades. This being caused by metal fatigue as a result of the tight radius. I might email laguna to see. My current problem is the table is not close to flat, or even perpendicular to the blade path. |
#19
Posted to rec.woodworking
|
|||
|
|||
Woodslicer band blades from Highland Hardware
"arw01" wrote in message oups.com... C&S wrote: They will make them any size you want... you wil have to wait a while though. They wider blades also get thicker, and thicker is not good on the smaller wheels of the Ryobi bs50n. When I researched buying this bandsaw used, it was noted they tended to break the wider blades. This being caused by metal fatigue as a result of the tight radius. I might email laguna to see. My current problem is the table is not close to flat, or even perpendicular to the blade path. Sorry, I was referring to the woodslicer. Which BTW only comes in 1/2" and 5/8" I thought the Laguna's resaw king was a 1" blade. Yes, Laguna recomends that the RK only be used on machines with 18" or greater diameter wheels. -Steve |
#20
Posted to rec.woodworking
|
|||
|
|||
Woodslicer band blades from Highland Hardware
"C&S" wrote in message ... Sorry, I was referring to the woodslicer. Which BTW only comes in 1/2" and 5/8" I thought the Laguna's resaw king was a 1" blade. Yes, Laguna recomends that the RK only be used on machines with 18" or greater diameter wheels. -Steve Steve, where do you read or see that Laguna recommends the RK/ResawKing only on machines with 18" or greater diameter wheels? I don't doubt you as that is recommended by many blade makers. The reason I ask is I am considering a 16" Laguna and Laguna often has sales on 14" and 16" band saws packages with ResawKings packaged with the deal. I want to be fully loaded with questions when I talk to them about the saw. Thanks. |
#21
Posted to rec.woodworking
|
|||
|
|||
Woodslicer band blades from Highland Hardware
Steve, where do you read or see that Laguna recommends the RK/ResawKing
only on machines with 18" or greater diameter wheels? I don't doubt you as that is recommended by many blade makers. The reason I ask is I am considering a 16" Laguna and Laguna often has sales on 14" and 16" band saws packages with ResawKings packaged with the deal. I want to be fully loaded with questions when I talk to them about the saw. They may have changed their rhetoric, but that's what I recall from about 2 years ago when I was researching bandsaw purchases. Perhaps my memory does not serve me correctly. -Steve |
#22
Posted to rec.woodworking
|
|||
|
|||
Woodslicer band blades from Highland Hardware
"C&S" wrote in message ... They may have changed their rhetoric, but that's what I recall from about 2 years ago when I was researching bandsaw purchases. Perhaps my memory does not serve me correctly. I talked to the MiniMax people today and asked them about the wider blades and smaller diameter wheel band saws. They indicated that the latest blades today are typically thinner and can be used on the smaller saws. |
Reply |
Thread Tools | Search this Thread |
Display Modes | |
|
|