Home |
Search |
Today's Posts |
|
UK diy (uk.d-i-y) For the discussion of all topics related to diy (do-it-yourself) in the UK. All levels of experience and proficency are welcome to join in to ask questions or offer solutions. |
Reply |
|
|
LinkBack | Thread Tools | Display Modes |
#1
|
|||
|
|||
How much does a 'standard' paving slab weigh?
How much does a 'standard' 600mm x 900mm paving slab weigh
(approximately)? I want to know so I can guesstimate how many I can put in the back of my car. -- Chris Green |
#2
|
|||
|
|||
How much does a 'standard' paving slab weigh?
|
#3
|
|||
|
|||
How much does a 'standard' paving slab weigh?
Set Square wrote:
In an earlier contribution to this discussion, wrote: How much does a 'standard' 600mm x 900mm paving slab weigh (approximately)? I want to know so I can guesstimate how many I can put in the back of my car. If you're talking about the pressed granite sort used by local authorities, I always reckon that a 2x2 weighs a hundredweight, and a 3x2 a hundredweight and a half. On that basis, one of your 600x900 (nearly a 3x2) will be about 70Kg. Thanks, so about a person per slab, maybe two lots of 5 would be sensible then. -- Chris Green |
#4
|
|||
|
|||
How much does a 'standard' paving slab weigh?
In message , Set Square
writes In an earlier contribution to this discussion, wrote: How much does a 'standard' 600mm x 900mm paving slab weigh (approximately)? I want to know so I can guesstimate how many I can put in the back of my car. If you're talking about the pressed granite sort used by local authorities, I always reckon that a 2x2 weighs a hundredweight, and a 3x2 a hundredweight and a half. On that basis, one of your 600x900 (nearly a 3x2) will be about 70Kg. Not a bad estimate. There is a table down towards the bottom of this page on Cormaic's excellent site.: http://www.pavingexpert.com/pccflag1.htm It gives approx. weight for 600x900x50 mm flags of 64 kg. All I know is if you are trying the lay the buggers, they are bloody heavy, and hard work to lay if you've not had plenty of practise. -- Chris French, Leeds |
#6
|
|||
|
|||
How much does a 'standard' paving slab weigh?
"Set Square" wrote in message ... In an earlier contribution to this discussion, wrote: Set Square wrote: In an earlier contribution to this discussion, wrote: How much does a 'standard' 600mm x 900mm paving slab weigh (approximately)? I want to know so I can guesstimate how many I can put in the back of my car. If you're talking about the pressed granite sort used by local authorities, I always reckon that a 2x2 weighs a hundredweight, and a 3x2 a hundredweight and a half. On that basis, one of your 600x900 (nearly a 3x2) will be about 70Kg. Thanks, so about a person per slab, maybe two lots of 5 would be sensible then. I don't think I'd want to carry 5 at once in my car. OK, they weigh about the same as 5 people - but you'll still presumably have a driver?! Also, the distribution is likely result in far more load on the back wheels than when you have 5 people in the car. For most cars, 3 at a time would probably be a sensible limit. -- Cheers, Set Square ______ Please reply to newsgroup. Reply address is invalid. Wouldn't it be most simpler and cheaper to have them all delivered in one go. Saves on petrol, probabl damage to vehicle etc. -- troubleinstore http://www.tuppencechange.co.uk Personal mail can be sent via website Email address on posting is ficticous and used as spam trap --- Outgoing mail is certified Virus Free. Checked by AVG anti-virus system (http://www.grisoft.com). Version: 6.0.708 / Virus Database: 464 - Release Date: 18/06/2004 |
#7
|
|||
|
|||
How much does a 'standard' paving slab weigh?
chris French wrote:
http://www.pavingexpert.com/pccflag1.htm It gives approx. weight for 600x900x50 mm flags of 64 kg. All I know is if you are trying the lay the buggers, they are bloody heavy, and hard work to lay if you've not had plenty of practise. I was fascinated to watch some cut stone paving being laid in a pedestrianisation project. They used a neat little machine with a big suction hose to lift and place each slab. Chris -- Chris J Dixon Nottingham UK Have dancing shoes, will ceilidh. |
#8
|
|||
|
|||
How much does a 'standard' paving slab weigh?
|
#9
|
|||
|
|||
How much does a 'standard' paving slab weigh?
|
#10
|
|||
|
|||
How much does a 'standard' paving slab weigh?
In an earlier contribution to this discussion,
Matt Beard wrote: wrote in message ... How much does a paving slab weigh? A stone? :-) Very droll! g. In reality, more like 12 stone. Is that a boulder? -- Cheers, Set Square ______ Please reply to newsgroup. Reply address is invalid. |
#11
|
|||
|
|||
How much does a 'standard' paving slab weigh?
wrote in message ... Set Square wrote: In an earlier contribution to this discussion, wrote: How much does a 'standard' 600mm x 900mm paving slab weigh (approximately)? I want to know so I can guesstimate how many I can put in the back of my car. If you're talking about the pressed granite sort used by local authorities, I always reckon that a 2x2 weighs a hundredweight, and a 3x2 a hundredweight and a half. On that basis, one of your 600x900 (nearly a 3x2) will be about 70Kg. Thanks, so about a person per slab, maybe two lots of 5 would be sensible then. Look in your handbook for the maximum permitted tow hook weight to get an idea of what the boot can cope with. You can go up slightly on that, because the moment arm is less, but not by much. My guess would be two or three slabs in the average car. Colin Bignell |
#12
|
|||
|
|||
How much does a 'standard' paving slab weigh?
|
#13
|
|||
|
|||
How much does a 'standard' paving slab weigh?
"nightjar" nightjar@ insert_my_surname_here.uk.com wrote:
wrote in message ... Set Square wrote: In an earlier contribution to this discussion, wrote: How much does a 'standard' 600mm x 900mm paving slab weigh (approximately)? I want to know so I can guesstimate how many I can put in the back of my car. If you're talking about the pressed granite sort used by local authorities, I always reckon that a 2x2 weighs a hundredweight, and a 3x2 a hundredweight and a half. On that basis, one of your 600x900 (nearly a 3x2) will be about 70Kg. Thanks, so about a person per slab, maybe two lots of 5 would be sensible then. Look in your handbook for the maximum permitted tow hook weight to get an idea of what the boot can cope with. You can go up slightly on that, because the moment arm is less, but not by much. My guess would be two or three slabs in the average car. It depends rather whether you put the slabs behind or in front of the rear wheels. If they're in front of the rear wheels then I think you can quite legitimately load the car up to its maximum permitted weight. The car is an XM hatchback, i.e. it's a big car, and I will lower the back seats and put the slabs where the back seats were. -- Chris Green |
#14
|
|||
|
|||
How much does a 'standard' paving slab weigh?
wrote:
"nightjar" nightjar@ insert_my_surname_here.uk.com wrote: wrote in message ... Set Square wrote: In an earlier contribution to this discussion, wrote: How much does a 'standard' 600mm x 900mm paving slab weigh (approximately)? I want to know so I can guesstimate how many I can put in the back of my car. If you're talking about the pressed granite sort used by local authorities, I always reckon that a 2x2 weighs a hundredweight, and a 3x2 a hundredweight and a half. On that basis, one of your 600x900 (nearly a 3x2) will be about 70Kg. Thanks, so about a person per slab, maybe two lots of 5 would be sensible then. Look in your handbook for the maximum permitted tow hook weight to get an idea of what the boot can cope with. You can go up slightly on that, because the moment arm is less, but not by much. My guess would be two or three slabs in the average car. It depends rather whether you put the slabs behind or in front of the rear wheels. If they're in front of the rear wheels then I think you can quite legitimately load the car up to its maximum permitted weight. The car is an XM hatchback, i.e. it's a big car, and I will lower the back seats and put the slabs where the back seats were. I've checked the XM specifications, maximum payload is between 500 and 550kg according to model, so 5 slabs should be OK (350kg plus me). I've also found the maximum towing weight which is way more than I thought it was - can I even pull a two horse trailer legally, wow! -- Chris Green |
#15
|
|||
|
|||
How much does a 'standard' paving slab weigh?
Look in your handbook for the maximum permitted tow hook weight to get an
idea of what the boot can cope with. You can go up slightly on that, because the moment arm is less, but not by much. The maximum tow bar weight has very little to do with the rear axle maximum weight. Almost no car will allow more than 100kg on the towbar (whilst 75kg is more normal) whilst the majority will allow you to exceed that as useful load on the rear axle. Remember that when towing with a 70kg noseweight, you are still allowed to use the boot, provided you don't exceed MAM or GTW. As a very rough estimate, you can fill the boot with half the useful load (MAM-kerb weight) of the vehicle. However, if you are cutting it that fine, then you should book an appointment at a public weigh station and check it. You will then have a much better feel for how much you can take in one go, which may be very useful for the future, or if you will need many trips. Note that you can't be done for being overweight on a trip to the weigh point, provided you don't take the **** and can justify your calculations. Overloading vehicles is dangerous and you can get really quite severe penalties for it, but the fact that you asked the question suggests that you have the right attitude. I saw a complete nutter loading up in B&Q a few weeks ago. He had a Ford Tourneo (small minibus transit van) that required him to place almost the entire load behind the rear axle. A quick calculation showed that he loaded over a tonne into that gap. I reckon he exceed not only MAM by around 200kg, but the rear axle weight by a whopping 500kg. I seriously considered phoning the police, whilst this nutter thought it was a great laugh trying to squeeze in one more dense concrete block or bag of plaster. When it comes to building materials, vans and cars are seriously weight limited, not volume. Christian. |
#16
|
|||
|
|||
How much does a 'standard' paving slab weigh?
I've checked the XM specifications, maximum payload is between 500 and
550kg according to model, so 5 slabs should be OK (350kg plus me). Put this would require even loading. Check the rear axle limit and make sure you don't exceed it. Alternatively, spread the load throughout. Put a slab in the passenger seat and two either side of the back seat. The remaining two can go in the boot. This will ensure you can use the full load available. I've also found the maximum towing weight which is way more than I thought it was - can I even pull a two horse trailer legally, wow! Be careful. Often the legal weight limit published by the car manufacturer is too high for safety and is based on getting the thing going on a certain slope. However, to prevent instability and snaking, you shouldn't exceed 85% of your car's kerb weight, which is usually less than the published braked trailer limit. An experienced tower could get away with 100% of kerb weight, but don't do this until experienced and NEVER exceed 60mph with a trailer. It isn't big, it isn't clever and may kill someone. Instability can bite suddenly at high speed and it is very easy to forget that you have the trailer on the back (at least it is for me, as the van is wide enough to obscure most trailers). Christian. |
#17
|
|||
|
|||
How much does a 'standard' paving slab weigh?
Put this would require even loading. Check the rear axle limit and make
sure you don't exceed it. P.S. When loading unfamiliar building materials, take an old set of bathroom scales along and weigh everything before purchasing/loading. Christian. |
#18
|
|||
|
|||
How much does a 'standard' paving slab weigh?
Christian McArdle wrote:
I've also found the maximum towing weight which is way more than I thought it was - can I even pull a two horse trailer legally, wow! Be careful. Often the legal weight limit published by the car manufacturer is too high for safety and is based on getting the thing going on a certain There is *no* "legal weight limit" for cars in the UK. See:- http://www.dft.gov.uk/stellent/group...ds_506866.hcsp slope. However, to prevent instability and snaking, you shouldn't exceed 85% of your car's kerb weight, which is usually less than the published braked trailer limit. An experienced tower could get away with 100% of kerb weight, but don't do this until experienced and NEVER exceed 60mph with a trailer. It isn't big, it isn't clever and may kill someone. Instability can bite suddenly at high speed and it is very easy to forget that you have the trailer on the back (at least it is for me, as the van is wide enough to obscure most trailers). I'm not aiming to pull anything near the manufacturer's suggested maximum, I was just commenting that I was surprised how much it was. In fact I doubt if I'll be towing anything in the immedate future. -- Chris Green |
#19
|
|||
|
|||
How much does a 'standard' paving slab weigh?
Christian McArdle wrote:
Look in your handbook for the maximum permitted tow hook weight to get an idea of what the boot can cope with. You can go up slightly on that, because the moment arm is less, but not by much. The maximum tow bar weight has very little to do with the rear axle maximum weight. Almost no car will allow more than 100kg on the towbar (whilst 75kg is more normal) whilst the majority will allow you to exceed that as useful load on the rear axle. Remember that when towing with a 70kg noseweight, you are still allowed to use the boot, provided you don't exceed MAM or GTW. The XMs have two different tow bar maximums, some are 70kg, some are 100kg. Since the rear wheels are very near the back I agree that I don't see that the towbar maximum has much to do with it. As a very rough estimate, you can fill the boot with half the useful load (MAM-kerb weight) of the vehicle. However, if you are cutting it that fine, then you should book an appointment at a public weigh station and check it. You will then have a much better feel for how much you can take in one go, which may be very useful for the future, or if you will need many trips. Note that you can't be done for being overweight on a trip to the weigh point, provided you don't take the **** and can justify your calculations. I don't *think* cars (i.e. passenger carrying vehicles) have a legal maximum weight, there are just the manufacturer's recommendations. This certainly applies to trailers towed by cars but I'm not quite sure about the loading of the car. Overloading vehicles is dangerous and you can get really quite severe penalties for it, but the fact that you asked the question suggests that you have the right attitude. I saw a complete nutter loading up in B&Q a few weeks ago. He had a Ford Tourneo (small minibus transit van) that required him to place almost the entire load behind the rear axle. A quick calculation showed that he loaded over a tonne into that gap. I reckon he exceed not only MAM by around 200kg, but the rear axle weight by a whopping 500kg. I seriously considered phoning the police, whilst this nutter thought it was a great laugh trying to squeeze in one more dense concrete block or bag of plaster. When it comes to building materials, vans and cars are seriously weight limited, not volume. Since he was overloading a van then there would be a legal (plated somewhere) limit for the van's maximum total weight. -- Chris Green |
#20
|
|||
|
|||
How much does a 'standard' paving slab weigh?
There is *no* "legal weight limit" for cars in the UK. See:-
Just because there isn't a specific infringement, doesn't make it legal. I bet if you towed a full 3500kg behind a car they'd still do you. Whether it is under construction and use, or just simply dangerous driving or whatever, they'd still issue a prohibition and may prosecute. Saying to the magistrate that the fact that you've towed a 3500kg trailer whilst the vehicle manufacturer says anything over 1300kg is dangerous, and you'll see what I mean. Christian. |
#21
|
|||
|
|||
How much does a 'standard' paving slab weigh?
"Christian McArdle" wrote in message t... There is *no* "legal weight limit" for cars in the UK. See:- Just because there isn't a specific infringement, doesn't make it legal. I bet if you towed a full 3500kg behind a car they'd still do you. Whether it is under construction and use, or just simply dangerous driving or whatever, they'd still issue a prohibition and may prosecute. Saying to the magistrate that the fact that you've towed a 3500kg trailer whilst the vehicle manufacturer says anything over 1300kg is dangerous, and you'll see what I mean. Indeed: b. A person is to be regarded as driving dangerously if it would be obvious to a competent and careful driver that driving the vehicle in its current state would be dangerous. In determining the state of the vehicle for this purpose, regard may be had to anything attached to or carried on or in it and to the manner in which it is attached or carried. THE MAXIMUM PENALTY FOR DANGEROUS DRIVING IS 2 YEARS IMPRISONMENT. THE MAXIMUM PENALTY FOR CAUSING DEATH BY DANGEROUS DRIVING IS 10 YEARS IMPRISONMENT. from the same website as referred to. -- Bob Mannix (anti-spam is as easy as 1-2-3 - not) |
#22
|
|||
|
|||
How much does a 'standard' paving slab weigh?
Christian McArdle wrote:
There is *no* "legal weight limit" for cars in the UK. See:- Just because there isn't a specific infringement, doesn't make it legal. I bet if you towed a full 3500kg behind a car they'd still do you. Whether it is under construction and use, or just simply dangerous driving or whatever, they'd still issue a prohibition and may prosecute. Saying to the magistrate that the fact that you've towed a 3500kg trailer whilst the vehicle manufacturer says anything over 1300kg is dangerous, and you'll see what I mean. As I said before there is no legal maximum limit. The law does not state that if you exceed a specified trailer weight it then becomes automatically illegal. I think you'll find in fact that there is no maximum trailer weight specified (as a recommended maximum) for many cars, especially older ones. I quite agree (and so does the URL I posted) that if you exceed the manufacturer's recommended weight it will be used as part of the evidence if you get prosecuted for having a dangerous load or some such. however you can't be prosecuted specifically for 'too much weight' because there isn't a weight limit. -- Chris Green |
#23
|
|||
|
|||
How much does a 'standard' paving slab weigh?
however you can't be prosecuted specifically for 'too much weight' because
there isn't a weight limit. For the vast overwhelming majority of cars sold in the last 30 years, the manufacturers publish a limit. Just because that limit isn't totally supported by specific legislation doesn't mean that you won't get done for dangerous driving by exceeding it. The manufacturers have stated that, in their opinion, the car is dangerous to drive above that weight. If you want to defend yourself, you have to explain why the designers of the vehicle know less about the safe towing limit than you do. Also, I'd guess a 'DD40' conviction would be worse on your record than a 'CU50'. Getting insurance with a DD code on your licence must be pretty damn hard. Note that there are loads of things you may be prosecuted for whilst driving that don't have a specific piece of legislation. They are just prosecuted under a general careless or dangerous driving charge. Christian. |
#24
|
|||
|
|||
How much does a 'standard' paving slab weigh?
Christian McArdle wrote:
Note that there are loads of things you may be prosecuted for whilst driving that don't have a specific piece of legislation. They are just prosecuted under a general careless or dangerous driving charge. Well yes, but that's hardly relevant is it. There *is* a speed limit and you can be prosecuted simply for exceeding it. You can also be prosecuted for careless/dangerous driving if you go round a corner too fast but lower than the speed limit. However you wouldn't thus say "there is a legal speed limit on this corner (that is lower than the general speed limit)". -- Chris Green |
#25
|
|||
|
|||
How much does a 'standard' paving slab weigh?
wrote in message ... .... It depends rather whether you put the slabs behind or in front of the rear wheels. If they're in front of the rear wheels then I think you can quite legitimately load the car up to its maximum permitted weight. The car is an XM hatchback, i.e. it's a big car, and I will lower the back seats and put the slabs where the back seats were. The MGW assumes that the load is distributed rather more evenly than that. Personally, I would have the slabs delivered, even though I have a van that would take the lot in one go. Colin Bignell |
#26
|
|||
|
|||
How much does a 'standard' paving slab weigh?
You can also be prosecuted for careless/dangerous driving if you
go round a corner too fast but lower than the speed limit. But the manufacturer's limits are much better defined than a speed round a corner, so although they would be prosecuted under a general provision, the offence is likely to be accurately determined by your failure to comply with the manufacturer's recommendations. In fact, your failure to do so can probably be measured more accurately than your speed! Christian. |
#27
|
|||
|
|||
How much does a 'standard' paving slab weigh?
"nightjar" nightjar@ insert_my_surname_here.uk.com wrote:
wrote in message ... ... It depends rather whether you put the slabs behind or in front of the rear wheels. If they're in front of the rear wheels then I think you can quite legitimately load the car up to its maximum permitted weight. The car is an XM hatchback, i.e. it's a big car, and I will lower the back seats and put the slabs where the back seats were. The MGW assumes that the load is distributed rather more evenly than that. Personally, I would have the slabs delivered, even though I have a van that would take the lot in one go. Since they were being given to me free I could hardly "have them delivered". Anyway we collected them five at a time last night, spread them around on the floor with the rear seats down. The XM's self levelling suspension coped fine, just a few clicks of the hydraulic pump after loading them and it was back to the normal ride height. The car handled quite normally with no problems although of course I was relatively cautious. 400kg is well within the maximum load so that was to be expected I suppose. -- Chris Green |
#28
Posted to uk.d-i-y
|
|||
|
|||
How much does a 'standard' paving slab weigh?
replying to Set Square, Turboweasel wrote:
Just carried 9 in the back of my volvo, with spring assisters lol. wasnt bad! -- posted from http://www.homeownershub.com/uk-diy/...igh-87701-.htm |
#29
Posted to uk.d-i-y
|
|||
|
|||
How much does a 'standard' paving slab weigh?
Turboweasel wrote:
Just carried 9 in the back of my volvo As Chris is still posting here, perhaps he'll tell us how many times he's replaced his car since asking that question twelve years ago ... |
#30
Posted to uk.d-i-y
|
|||
|
|||
How much does a 'standard' paving slab weigh?
On 08/06/16 23:44, Turboweasel wrote:
replying to Set Square, Turboweasel wrote: Just carried 9 in the back of my volvo, with spring assisters lol. wasnt bad! IIRC around 20kg -- "It is an established fact to 97% confidence limits that left wing conspirators see right wing conspiracies everywhere" |
#31
Posted to uk.d-i-y
|
|||
|
|||
How much does a 'standard' paving slab weigh?
On 09/06/2016 09:47, The Natural Philosopher wrote:
On 08/06/16 23:44, Turboweasel wrote: replying to Set Square, Turboweasel wrote: Just carried 9 in the back of my volvo, with spring assisters lol. wasnt bad! IIRC around 20kg It does rather depend on the size. The last batch of 600x600x40mm slabs I bought were 33kg each. -- Cheers, John. /================================================== ===============\ | Internode Ltd - http://www.internode.co.uk | |-----------------------------------------------------------------| | John Rumm - john(at)internode(dot)co(dot)uk | \================================================= ================/ |
#32
Posted to uk.d-i-y
|
|||
|
|||
How much does a 'standard' paving slab weigh?
On 09/06/16 09:55, John Rumm wrote:
On 09/06/2016 09:47, The Natural Philosopher wrote: On 08/06/16 23:44, Turboweasel wrote: replying to Set Square, Turboweasel wrote: Just carried 9 in the back of my volvo, with spring assisters lol. wasnt bad! IIRC around 20kg It does rather depend on the size. The last batch of 600x600x40mm slabs I bought were 33kg each. Ah, I don't think of those as 'standard'. -- It is hard to imagine a more stupid decision or more dangerous way of making decisions than by putting those decisions in the hands of people who pay no price for being wrong. Thomas Sowell |
#33
Posted to uk.d-i-y
|
|||
|
|||
How much does a 'standard' paving slab weigh?
On Thursday, 9 June 2016 10:21:47 UTC+1, The Natural Philosopher wrote:
On 09/06/16 09:55, John Rumm wrote: On 09/06/2016 09:47, The Natural Philosopher wrote: IIRC around 20kg It does rather depend on the size. The last batch of 600x600x40mm slabs I bought were 33kg each. Ah, I don't think of those as 'standard'. Your original 2004 answer was more accurate: Too ****in much NT |
#34
Posted to uk.d-i-y
|
|||
|
|||
How much does a 'standard' paving slab weigh?
On 09/06/2016 10:21, The Natural Philosopher wrote:
On 09/06/16 09:55, John Rumm wrote: On 09/06/2016 09:47, The Natural Philosopher wrote: On 08/06/16 23:44, Turboweasel wrote: replying to Set Square, Turboweasel wrote: Just carried 9 in the back of my volvo, with spring assisters lol. wasnt bad! IIRC around 20kg It does rather depend on the size. The last batch of 600x600x40mm slabs I bought were 33kg each. Ah, I don't think of those as 'standard'. Not sure there is *one" standard as such. Edges that are 300, 450, 600mm in various combinations are quite common. Other sizes are not unknown though. -- Cheers, John. /================================================== ===============\ | Internode Ltd - http://www.internode.co.uk | |-----------------------------------------------------------------| | John Rumm - john(at)internode(dot)co(dot)uk | \================================================= ================/ |
#35
Posted to uk.d-i-y
|
|||
|
|||
How much does a 'standard' paving slab weigh?
On Thu, 09 Jun 2016 11:50:26 +0100, pamela wrote:
On 23:44 8 Jun 2016, Turboweasel wrote: replying to Set Square, Turboweasel wrote: Just carried 9 in the back of my volvo, with spring assisters lol. wasnt bad! You're replying to a post from 2004. He is from that house owner site that copies this USENET group to a web page. For some reason none of the users seem to see the posting date. I have actually been to the site and the date is stated quite clearly. |
#36
Posted to uk.d-i-y
|
|||
|
|||
How much does a 'standard' paving slab weigh?
On 08/06/2016 23:44, Turboweasel wrote:
replying to Set Square, Turboweasel wrote: Just carried 9 in the back of my volvo, with spring assisters lol. wasnt bad! 12 years ago when the question was posted paving slabs were heavier -- mailto: news {at} admac {dot] myzen {dot} co {dot} uk |
#37
Posted to uk.d-i-y
|
|||
|
|||
How much does a 'standard' paving slab weigh?
Do they get heavier when they've been laid a while? Maybe absorbing water?
I recently had to lift a couple of slabs when I put up my new fence, and they were really **** heavy. Much more than the 20kg bags of postfix I was carting around. |
#38
Posted to uk.d-i-y
|
|||
|
|||
How much does a 'standard' paving slab weigh?
On Thu, 9 Jun 2016 09:55:14 +0100, John Rumm wrote:
On 09/06/2016 09:47, The Natural Philosopher wrote: On 08/06/16 23:44, Turboweasel wrote: replying to Set Square, Turboweasel wrote: Just carried 9 in the back of my volvo, with spring assisters lol. wasnt bad! IIRC around 20kg It does rather depend on the size. The last batch of 600x600x40mm slabs I bought were 33kg each. I've always worked on a relative density of 2.4 - for slabs in the real world this woul be 2.4kg/li. So, 900x600x50: 9x6x0.5=27li, times 2.4=64.8(kg). The Paving Expert gives 64kg http://pavingexpert.com/pccflag1.htm about 80% of the way down the page. -- Peter. The gods will stay away whilst religions hold sway |
#39
Posted to uk.d-i-y
|
|||
|
|||
How much does a 'standard' paving slab weigh?
replying to alan_m, Turboweasel wrote:
Haha, yeah but these are old paving slabs, at least 1970s -- posted from http://www.homeownershub.com/uk-diy/...igh-87701-.htm |
#40
Posted to uk.d-i-y
|
|||
|
|||
How much does a 'standard' paving slab weigh?
replying to pamela, Turboweasel wrote:
I know, but shows people still read this to find out stuff -- posted from http://www.homeownershub.com/uk-diy/...igh-87701-.htm |
Reply |
|
Thread Tools | Search this Thread |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Forum | |||
Paving Slabs | UK diy | |||
SDS drill with standard chuck | UK diy | |||
Basin Fittings Non Standard | UK diy | |||
Block paving | UK diy | |||
Concrete slab advice | UK diy |