Home |
Search |
Today's Posts |
|
UK diy (uk.d-i-y) For the discussion of all topics related to diy (do-it-yourself) in the UK. All levels of experience and proficency are welcome to join in to ask questions or offer solutions. |
Reply |
|
LinkBack | Thread Tools | Display Modes |
#1
|
|||
|
|||
GSH & HW. novice questions .pls help
I've been in my current house for 5 yrs but never bothered looking at my CH system, but recently my pump failed ( impeller snapped of shaft ). I think this is probably an effect of the system not running properly however, so I've decided to pay attention to it and figure out what should & shouldn't be happeneing. In order to try and get some clear answers, I've done some sketches and provided links to support my questions :- http://freespace.virgin.net/ian.jarvo/piping arrangement.pdf http://freespace.virgin.net/ian.jarvo/Valve & Thermo diagrams.pdf http://freespace.virgin.net/ian.jarvo/wires.jpg http://freespace.virgin.net/ian.jarvo/wiring layout.pdf Q1. Does the hot water circuit use pump or just gravity? Q2. Should switching to HW on my control unit make the motorized valve shut ( & trip off the pump if answer to item #1 is gravity )? Q3. On the valve, does switching from auto to manual make valve shut or stay open? Q4. Is one of the 22m pipes in the piping arrangement just the vent to my header tank? Q5. Why have a -15°-+10 thermostat in the garage? , but none in the house , and in which parameters does it work. Q6. Further #5 I don't have an internal thermostat. Would I benefit from intalling one Please describe where it should be hooked up to. Q7. Instead of an internal thermostat, would a string of thermostatically controlled radiator valves make more sense? Q8. Roughly how much would a thermostat cost compared to individual radiator valves? Q9. What point do you typically drain the system from ? Should there be a 'y' valve somewhere that I could stick a hose pipe on? Q10. I've never attempted to put any corrosion inhibitor into the header tank and there's no filtration of any kind inthe system. Should there be either ? Q11. For future maintenance of pump/valve/boiler, would my system benefit from some isolation valves installed on the garage wall per my piping sketch. Please advise where I might put one or two valves to avoid having to frequently drain the whole system when things go wrong. More questions will result from the answers I receive Please cc newsgroup responses to Thanks in advance IJ |
#2
|
|||
|
|||
GSH & HW. novice questions .pls help
And also this is a handy site to have a read through.
http://www.diyfaq.org.uk/plumbing/plumbingpage2.html --- http://www.basecuritysystems.no-ip.com Outgoing mail is certified Virus Free. Checked by AVG anti-virus system (http://www.grisoft.com). Version: 6.0.519 / Virus Database: 317 - Release Date: 17/09/03 |
#3
|
|||
|
|||
GSH & HW. novice questions .pls help
"BigWallop" wrote in message ... And also this is a handy site to have a read through. http://www.diyfaq.org.uk/plumbing/plumbingpage2.html --- http://www.basecuritysystems.no-ip.com Outgoing mail is certified Virus Free. Checked by AVG anti-virus system (http://www.grisoft.com). Version: 6.0.519 / Virus Database: 317 - Release Date: 17/09/03 Actually, I don't think it helps, it just gets me past first base, but the following edited list still applies :- Q1. Does the hot water circuit use pump or just gravity? Q2. Should switching to HW on my control unit make the motorized valve shut ( & trip off the pump if answer to item #1 is gravity )? Q4. Is one of the 22m pipes in the piping arrangement just the vent to my header tank? Q5. Why have a -15°-+10 thermostat in the garage? , but none in the house , and in which parameters does it work. Q10. I've never attempted to put any corrosion inhibitor into the header tank and there's no filtration of any kind in the system. Should there be either ? Q11. I've just bought replacement sychron motor, but I can tell which position the gear quandrant should be in when I mount the motor in position. All I can tell is when the motor is hanging loose and I switch W+H, then motor activates without stopping. Q12 my zone valve has 5 wires, brown/blue , white/black and green earth. The black/white is a contact switch which mades contact as the gear quadrant ges down. What is supposed to happen as a result of the black/white contact being made ? Q13 My control/timer unit is a randall 103E . I can unscrew the bottom plate but how the hell does the face plate come off so I can see the wiring ? Q14 Throughout all the messing about I've been doing, in every condition the CH pump appears to be constantly running. Surely something must shut down the pump ? Q15 My HW tank has two 15mm pipes which have concentric reducers terminating at the top of the tank ( I pressume some kind of HW circuit bleed. There are screwdriver slots in the top of the reducers, but I would like to try and unscrew them as they made not go back in place. Has anyone ever seen such an arrangement and I am safe to try and uncrew them ? Help ! IJ |
#4
|
|||
|
|||
GSH & HW. novice questions .pls help
"Ebodski" wrote in message ... "BigWallop" wrote in message ... And also this is a handy site to have a read through. http://www.diyfaq.org.uk/plumbing/plumbingpage2.html --- http://www.basecuritysystems.no-ip.com Outgoing mail is certified Virus Free. Checked by AVG anti-virus system (http://www.grisoft.com). Version: 6.0.519 / Virus Database: 317 - Release Date: 17/09/03 Actually, I don't think it helps, it just gets me past first base, but the following edited list still applies :- Q1. Does the hot water circuit use pump or just gravity? You'll have to trace back along the pipes from the coil in your hot water tank to find out. Q2. Should switching to HW on my control unit make the motorized valve shut ( & trip off the pump if answer to item #1 is gravity )? It depends on the type of system you have in Q1. Q4. Is one of the 22m pipes in the piping arrangement just the vent to my header tank? It depends on the type of system you have. Q5. Why have a -15°-+10 thermostat in the garage? , but none in the house , and in which parameters does it work. A thermostat fitted externally is more than likely a what is known as a frost guard. It works by sensing the external temperature and if it falls below the set level, then your heating kicks in to stop the house freezing. Q10. I've never attempted to put any corrosion inhibitor into the header tank and there's no filtration of any kind in the system. Should there be either ? Inhibitor is a good idea, especially in hard water areas (lots of lime and things in the water), but is not totally neccesary. Filters would only be used if the supply water was known to contain large contaminants, but if fitlering was needed on your system, then it should be documented on the boiler or a system diagram for cleaning routines. Q11. I've just bought replacement sychron motor, but I can tell which position the gear quandrant should be in when I mount the motor in position. All I can tell is when the motor is hanging loose and I switch W+H, then motor activates without stopping. A synchron motor, as with any standard motor, will continue to turn when energised until told to stop by some kind of switching system. The small micro-switch in the motorised valve is such a system. Q12 my zone valve has 5 wires, brown/blue , white/black and green earth. The black/white is a contact switch which mades contact as the gear quadrant ges down. What is supposed to happen as a result of the black/white contact being made ? A motorised valve has two wires which carry the power needed to make it turn. It also has some wires which connect to the switching in the valve head and these are used as signalling connections to the timers or programmers and tell the boiler to fire up or the pump to run or the system to shut down and switch off completely and it depends on how the system setup is configured. Q13 My control/timer unit is a randall 103E . I can unscrew the bottom plate but how the hell does the face plate come off so I can see the wiring ? Usually the timer/programmer seperates from the back plate by loosening, not removing, screws from the bottom or top of the unit. When loosened the face place lifts to 45 degree angle away from the screws and then lifts off completely when freed from moulded lugs on the back plate. Q14 Throughout all the messing about I've been doing, in every condition the CH pump appears to be constantly running. Surely something must shut down the pump ? This switching depends usually on the motorised valves. Motorised valves contain micro-switches that, when wired to suit the system, tell the boiler to fire up, tell the pump to run when needed and generally take care of the flow of heated water arond the system. Q15 My HW tank has two 15mm pipes which have concentric reducers terminating at the top of the tank ( I pressume some kind of HW circuit bleed. There are screwdriver slots in the top of the reducers, but I would like to try and unscrew them as they made not go back in place. Has anyone ever seen such an arrangement and I am safe to try and uncrew them ? These reducers sound very like air bleeder valves. If you slowly undo one of the bolts, water should rise out. If you are getting air or even just a hissing sound, then your system has to much air and not enough water. Heating air and trying to circulate it around your water and radiator circuits is not the best way to heat the house. You really need all water in the pipework to do this the most efficiently. Help ! IJ Have a look at the sites I offered and then try to trace the pipes in your system to where they match and where they differ. Make some drawings or notes on the things you discover that are different and then get back to us with a description and we'll try help you through what the differences are. |
#5
|
|||
|
|||
GSH & HW. novice questions .pls help
"BigWallop" wrote in message ... "Ebodski" wrote in message ... "BigWallop" wrote in message ... And also this is a handy site to have a read through. http://www.diyfaq.org.uk/plumbing/plumbingpage2.html --- http://www.basecuritysystems.no-ip.com Outgoing mail is certified Virus Free. Checked by AVG anti-virus system (http://www.grisoft.com). Version: 6.0.519 / Virus Database: 317 - Release Date: 17/09/03 Actually, I don't think it helps, it just gets me past first base, but the following edited list still applies :- Q1. Does the hot water circuit use pump or just gravity? You'll have to trace back along the pipes from the coil in your hot water tank to find out. Thats why I did this sketch. If you look you will see it is in the pumped line and tee'd off just before the zone valve. But I don't know whether this NEEDS the pump or whether gravity still works in the pump switched off http://freespace.virgin.net/ian.jarv...rrangement.pdf Q2. Should switching to HW on my control unit make the motorized valve shut ( & trip off the pump if answer to item #1 is gravity )? It depends on the type of system you have in Q1. Can you check the sketch & confirm what ystem I have. BTW in the sketch, the line to the kitchen should come off the middle pipe after the zone valve. I drew it wrong. Q4. Is one of the 22m pipes in the piping arrangement just the vent to my header tank? It depends on the type of system you have. Can you check the sketch & confirm ....... Q5. Why have a -15°-+10 thermostat in the garage? , but none in the house , and in which parameters does it work. A thermostat fitted externally is more than likely a what is known as a frost guard. It works by sensing the external temperature and if it falls below the set level, then your heating kicks in to stop the house freezing. Okay, makes sense. I can only tell if that functions in a few moths time.. Q10. I've never attempted to put any corrosion inhibitor into the header tank and there's no filtration of any kind in the system. Should there be either ? Inhibitor is a good idea, especially in hard water areas (lots of lime and things in the water), but is not totally neccesary. Filters would only be used if the supply water was known to contain large contaminants, but if fitlering was needed on your system, then it should be documented on the boiler or a system diagram for cleaning routines. Okay, no need to worry too much about that then. Q11. I've just bought replacement sychron motor, but I can tell which position the gear quandrant should be in when I mount the motor in position. All I can tell is when the motor is hanging loose and I switch W+H, then motor activates without stopping. A synchron motor, as with any standard motor, will continue to turn when energised until told to stop by some kind of switching system. The small micro-switch in the motorised valve is such a system. Ahh, I had a play with this whilst the motor was turning. It didn't make any difference. So maybe the microswitch could be cooked. PS did I put my life @ risk because I suspect the microswitch could be 240V.AC ? Q12 my zone valve has 5 wires, brown/blue , white/black and green earth. The black/white is a contact switch which mades contact as the gear quadrant ges down. What is supposed to happen as a result of the black/white contact being made ? A motorised valve has two wires which carry the power needed to make it turn. It also has some wires which connect to the switching in the valve head and these are used as signalling connections to the timers or programmers and tell the boiler to fire up or the pump to run or the system to shut down and switch off completely and it depends on how the system setup is configured. On Q11 you just told me that my black/white switch tripped of the motor. Is the 'signal' a micro amp signal. The linked sketch showed the wires in the junction box next to the zone valve. Can you shed any light on it in relation to my questions. http://freespace.virgin.net/ian.jarvo/wires.jpg Q13 My control/timer unit is a randall 103E . I can unscrew the bottom plate but how the hell does the face plate come off so I can see the wiring ? Usually the timer/programmer seperates from the back plate by loosening, not removing, screws from the bottom or top of the unit. When loosened the face place lifts to 45 degree angle away from the screws and then lifts off completely when freed from moulded lugs on the back plate. Hmmm. theres only one screw visible which I undid. All that came off as a result was the bottom coverpiece. I'll take a closer look later Q14 Throughout all the messing about I've been doing, in every condition the CH pump appears to be constantly running. Surely something must shut down the pump ? This switching depends usually on the motorised valves. Motorised valves contain micro-switches that, when wired to suit the system, tell the boiler to fire up, tell the pump to run when needed and generally take care of the flow of heated water arond the system. Could/should my 1-off zone valve with its single microswitch do anything else including switch off the synchron motor?. Please refer to my sketches Q15 My HW tank has two 15mm pipes which have concentric reducers terminating at the top of the tank ( I pressume some kind of HW circuit bleed. There are screwdriver slots in the top of the reducers, but I would like to try and unscrew them as they made not go back in place. Has anyone ever seen such an arrangement and I am safe to try and uncrew them ? These reducers sound very like air bleeder valves. If you slowly undo one of the bolts, water should rise out. If you are getting air or even just a hissing sound, then your system has to much air and not enough water. Heating air and trying to circulate it around your water and radiator circuits is not the best way to heat the house. You really need all water in the pipework to do this the most efficiently. This my make you LOL, but I actually work for a pump manufacturer and tender quotations for multi-megawatt powered pumpsets for oil riggs & refineries etc. The main thing I'm struggling with is not so much the piping, but the switching/signalling and whether it is all 240v. On major machinery, the instrument signals are 4-20mA. Help ! IJ Have a look at the sites I offered and then try to trace the pipes in your system to where they match and where they differ. Make some drawings or notes on the things you discover that are different and then get back to us with a description and we'll try help you through what the differences are. |
#6
|
|||
|
|||
GSH & HW. novice questions .pls help
From your sketches the system has a constant hot water circulation through
the pump any time the boiler fires up. This means that there is a thermostat on the hot water cylinder. Correct ? The motorised valve is only activated when you call for heat to the radiators. The wiring sketch shows a "?" on a pair of wires and is most likely the connection to the hot water cylinder thermostat. The frost guard 'stat will control the system by over riding the hot water circulation and only allow the heating to be called for by the radiators. Everything on the wiring will live mains voltage and should run at no more than 5 amps at total load. It may even be 3 amps depending on the pump size and switching loads of the 'stat and things. The motorised valve will only open when the programmer calls for heating to the radiator circuit. Unless you've seen things in the wrong places and the valve is actually a three port, two way valve, which is connected to the flow pipe after the pump and will swing an arm inside it between the hot water and heating circuits, or can be set by the system to stop in a mid point between the two circuits to allow heated water to flow through both circuits. A three port valve has three pipes going to in to it. One is the flow from the boiler, one is the flow to the hot water circuit and one is flow to the radiator circuit. From your sketch the system relize on the pump to circulate the heated water around the two circuits and is fed from a header tank. It looks to be a very basic, and very easily maintained, system. --- http://www.basecuritysystems.no-ip.com Outgoing mail is certified Virus Free. Checked by AVG anti-virus system (http://www.grisoft.com). Version: 6.0.519 / Virus Database: 317 - Release Date: 17/09/03 |
#7
|
|||
|
|||
GSH & HW. novice questions .pls help
Thanks for picking up on my queries BigW. I am an OK DIY'er, but I've never
payed any attention to CH/HW before. I got recently mugged by a plumber for £150 ( the wife called them in out of blind panic ) to put a new pump in, so now I've decided I need to get more genned up on the subject before winter sets in. I suspect you are right about the thermostat in the HW tank ( I'll check tonight ). However, if my boiler has a stat on it with a 140-180°F setting, I can't see the purpose of the stat on the HW tank i.e what will it activate/de-activate. If going from my sketch there is a permanent unvalved supply to my HW coil, then all that I can see could happen is that when the HW-tank thinks its hot enough, it stops the boiler GCV, but this would then stop the hot feed to the radiators wouldn't it when perhaps there was a demand ? I could understand the concept of a HW stat triggering a HW zone valve to close if one was installed... I think there is also a immersion heater in the tank but its knacked with the wiring ripped out of the wall socket. I think I need to verify what wiring exists & replace the heater. ( I thought that you didn't need an immersion heater if you had a boiler, but it now seems obvious that I should have one there as back-up in case the boiler goes down ) Re the zone valve, I assume 'activated' means opened and when no power is supplied the the valve it springs shut. Therefore there should only be a power supply to the valve when the 'water+heat' switch is toggled. Please confirm I've got my head round that one...... ....and how have you concluded the valve is three port ? Although my system may be better suited to a three port arrangement, I can definately assure you that the valve on my garage wall is a tower 672B 22m 2port valve with an earthwire, plus four other wires connected. Do you think I should replace the current 2 port with a 3-port , or just install a 2nd 2-port valve ( 15mm if available )on the HW line. Re the frost guard stat, you reckon this stat will 'only allow heating the be called for by the rads', but as I've stated above, the HW circuit has nothing to isolate it , so I can't visualise how this can happen when I have no stat in the house other than the rad-stat-valves. I can understand the concept of the frost stat just being a by-pass( short circuit ) to all the other controls such that it fires up the boiler ahead of the timer eg if I set it to zero°C... Does that make sense ? Finally the pump. Although it is clear that the HW is fed from a tee junction after the pump discharge, does this mean that it absolutely cannot be a gravity based HW circuit. If the boiler is in the garage and the HW tank is 3-4m above on the upstairs landing of the house, does it need the pump to get it round or will just the heat energy/pressure entered into the water force it round ? ( A am not 100% sure on how a gravity system should/could work. ) I'm sure if I checked my gas bills with other people I'll find out I've been wasting lots of cash running my system wrong. When I've got better informed, I want to mod my system so that the HW just gets hot & isolates itself until its needed and the CH does the same & perhaps stops the pump. I wan't to learn whether there should be more control over the pump, for instance when 'HW only' selected, can't the pump be tripped. Pls continue to help Cheers "BigWallop" wrote in message ... From your sketches the system has a constant hot water circulation through the pump any time the boiler fires up. This means that there is a thermostat on the hot water cylinder. Correct ? The motorised valve is only activated when you call for heat to the radiators. The wiring sketch shows a "?" on a pair of wires and is most likely the connection to the hot water cylinder thermostat. The frost guard 'stat will control the system by over riding the hot water circulation and only allow the heating to be called for by the radiators. Everything on the wiring will live mains voltage and should run at no more than 5 amps at total load. It may even be 3 amps depending on the pump size and switching loads of the 'stat and things. The motorised valve will only open when the programmer calls for heating to the radiator circuit. Unless you've seen things in the wrong places and the valve is actually a three port, two way valve, which is connected to the flow pipe after the pump and will swing an arm inside it between the hot water and heating circuits, or can be set by the system to stop in a mid point between the two circuits to allow heated water to flow through both circuits. A three port valve has three pipes going to in to it. One is the flow from the boiler, one is the flow to the hot water circuit and one is flow to the radiator circuit. From your sketch the system relize on the pump to circulate the heated water around the two circuits and is fed from a header tank. It looks to be a very basic, and very easily maintained, system. --- http://www.basecuritysystems.no-ip.com Outgoing mail is certified Virus Free. Checked by AVG anti-virus system (http://www.grisoft.com). Version: 6.0.519 / Virus Database: 317 - Release Date: 17/09/03 |
#8
|
|||
|
|||
GSH & HW. novice questions .pls help
BigWallop wrote:
Q11. I've just bought replacement sychron motor, but I can tell which position the gear quandrant should be in when I mount the motor in position. All I can tell is when the motor is hanging loose and I switch W+H, then motor activates without stopping. A synchron motor, as with any standard motor, will continue to turn when energised until told to stop by some kind of switching system. The small micro-switch in the motorised valve is such a system. With the plain 2 port valve the motor simply winds the valve open and the valve is not able to turn any further so the motor stops - crude but generally very reliable. Q13 My control/timer unit is a randall 103E . I can unscrew the bottom plate but how the hell does the face plate come off so I can see the wiring ? Usually the timer/programmer seperates from the back plate by loosening, not removing, screws from the bottom or top of the unit. When loosened the face place lifts to 45 degree angle away from the screws and then lifts off completely when freed from moulded lugs on the back plate. the bottom plate in this type (big rotarty thing with blue and red tags and a wheel in the top right corner) is removed this allows the whole unit to be slid upwards off the back plate. Have a look at the sites I offered and then try to trace the pipes in your system to where they match and where they differ. Make some drawings or notes on the things you discover that are different and then get back to us with a description and we'll try help you through what the differences are. Good advice. The FAQ is intended to take over where the basic diy manuals start saying 'leave this to the professionals'. The FAQ is not a primer on heating systems. -- Ed Sirett - Property maintainer and registered gas fitter. The FAQ for uk.diy is at www.diyfaq.org.uk Gas fitting FAQ http://www.makewrite.demon.co.uk/GasFitting.html Sealed CH FAQ http://www.makewrite.demon.co.uk/SealedCH.html |
#9
|
|||
|
|||
GSH & HW. novice questions .pls help
Q13 My control/timer unit is a randall 103E . I can unscrew the bottom plate but how the hell does the face plate come off so I can see the wiring ? the bottom plate in this type (big rotarty thing with blue and red tags and a wheel in the top right corner) is removed this allows the whole unit to be slid upwards off the back plate. Erm....sorry it was actually a 102E, apologies. The above made absolutely no sense so I checked and realised my error. Theres nothing rotary on this unit, just one single screw underneath which allows removal of a narrow rectangular plastic bottom plate. I can't see any obvious points to break it open. |
#10
|
|||
|
|||
GSH & HW. novice questions .pls help
On Fri, 19 Sep 2003 20:15:54 +0100, Ed Sirett
wrote: BigWallop wrote: Q11. I've just bought replacement sychron motor, but I can tell which position the gear quandrant should be in when I mount the motor in position. All I can tell is when the motor is hanging loose and I switch W+H, then motor activates without stopping. A synchron motor, as with any standard motor, will continue to turn when energised until told to stop by some kind of switching system. The small micro-switch in the motorised valve is such a system. With the plain 2 port valve the motor simply winds the valve open and the valve is not able to turn any further so the motor stops - crude but generally very reliable. On the subject of these zone or diverter valves with spring returns, I am sure I can remember that when I installed my first system (late seventies), the 2 port valves that I used were motorised in both directions - i.e. no spring return. IIRC, the motor had two windings or some means of effecting reverse and there was a live to drive it to open and another to drive it to close. Then the room and cylinder thermostats were change-over switches to do this. There was an auxilliary switch as now to provide the demand live to the boiler. Do you remember those and when and why they changed? This seems like a better way to do the job than a motor powered against a spring. ..andy To email, substitute .nospam with .gl |
#11
|
|||
|
|||
GSH & HW. novice questions .pls help
Hmmmmm.... this is getting strange, but your theory below might shed some
light on my latest findings :- I've just been meddling about with the valve in the garage with a multimeter. 1. The valve does have free movement albeit limited to about 30° max. Does that seem right or should it be more like 80-90° ? 2. With the control switch set on 'water plus heat' the motor starts turning, pressumably to open the valve. Looking at the motor direction of rotation, this should make the quadrant gear move CCW downwards. At this point I levered the quadrant down manually to trigger the microswitch, but nothing happened and the motor kept on turning. 3. Thinking that the microswitch was faulty, I turned my attention to that. It has three terminals but only 2 wires connected. A black wire underneath and a white wire in the middle and nothing connected to the top terminal. I removed the microswitch and tried continuity testing it. Between the two connected terminals it was a broken open circuit until the switch was depressed, then continuity was made. When I tested across the two end terminals I just got a widely fluctuating resistance of 10-70 ohms. 4. ...this is where I loose the plot ! Okay here goes..., with the black & white wires hanging loose but in a safe position, I switched on the system and the synchron motor starts turning. I'm not sure why, but I decided to switch off the system again and connect the black & white terminals together expecting the motor to stop. But when I switched on the system, the motor started turning again !!! My house is a late 60's semi which has a Vulcan boiler , tower 672B zone valve & 102E randall controller. Some of it was fitted in the 70s and maybe mods were done in the 80s Can anyone enlighten me on this as I'm lost cheers IJ "Andy Hall" wrote in message ... On Fri, 19 Sep 2003 20:15:54 +0100, Ed Sirett wrote: BigWallop wrote: Q11. I've just bought replacement sychron motor, but I can tell which position the gear quandrant should be in when I mount the motor in position. All I can tell is when the motor is hanging loose and I switch W+H, then motor activates without stopping. A synchron motor, as with any standard motor, will continue to turn when energised until told to stop by some kind of switching system. The small micro-switch in the motorised valve is such a system. With the plain 2 port valve the motor simply winds the valve open and the valve is not able to turn any further so the motor stops - crude but generally very reliable. On the subject of these zone or diverter valves with spring returns, I am sure I can remember that when I installed my first system (late seventies), the 2 port valves that I used were motorised in both directions - i.e. no spring return. IIRC, the motor had two windings or some means of effecting reverse and there was a live to drive it to open and another to drive it to close. Then the room and cylinder thermostats were change-over switches to do this. There was an auxilliary switch as now to provide the demand live to the boiler. Do you remember those and when and why they changed? This seems like a better way to do the job than a motor powered against a spring. .andy To email, substitute .nospam with .gl |
#12
|
|||
|
|||
GSH & HW. novice questions .pls help
In message , Ebodski
writes Q13 My control/timer unit is a randall 103E . I can unscrew the bottom plate but how the hell does the face plate come off so I can see the wiring ? the bottom plate in this type (big rotarty thing with blue and red tags and a wheel in the top right corner) is removed this allows the whole unit to be slid upwards off the back plate. Erm....sorry it was actually a 102E, apologies. The above made absolutely no sense so I checked and realised my error. Theres nothing rotary on this unit, just one single screw underneath which allows removal of a narrow rectangular plastic bottom plate. I can't see any obvious points to break it open. Push the bugger upwards once you've removed the screw. It's held on by the electrical contacts -- geoff |
#13
|
|||
|
|||
GSH & HW. novice questions .pls help
Have a read through these pages and see if you can identify your system from
the descriptions given of all the different parts and how they work. http://www.diyfaq.org.uk/plumbing/plumbingpage2.html --- http://www.basecuritysystems.no-ip.com Outgoing mail is certified Virus Free. Checked by AVG anti-virus system (http://www.grisoft.com). Version: 6.0.519 / Virus Database: 317 - Release Date: 17/09/03 |
#14
|
|||
|
|||
GSH & HW. novice questions .pls help
I have any my zone valve wiring bares no resemblance to the one on your
page. My zone valve has only 5 wires not six with no orange or grey. Pls see my post below. the microswitch doesn't do anything. the motor continuously turns as soon as I ask for water+heat regardless of whether the microswitch wires are separated or joined... "BigWallop" wrote in message ... Have a read through these pages and see if you can identify your system from the descriptions given of all the different parts and how they work. http://www.diyfaq.org.uk/plumbing/plumbingpage2.html --- http://www.basecuritysystems.no-ip.com Outgoing mail is certified Virus Free. Checked by AVG anti-virus system (http://www.grisoft.com). Version: 6.0.519 / Virus Database: 317 - Release Date: 17/09/03 |
#15
|
|||
|
|||
GSH & HW. novice questions .pls help
"Ebodski" wrote in message ... I have any my zone valve wiring bares no resemblance to the one on your page. My zone valve has only 5 wires not six with no orange or grey. Pls see my post below. the microswitch doesn't do anything. the motor continuously turns as soon as I ask for water+heat regardless of whether the microswitch wires are separated or joined... The motor will turn as soon as power goes to it and remains powered through the duration of the call for heat. The micro-switch activates the boiler and pump controls. The motor doesn't stop until it reaches the limit set by the cog wheel, so if the cog wheel breaks any teeth the motor will continue to turn. It is the cog wheel that moves the valve arm inside the valve and not the motor itself. The micro-switch can have as many connections as is needed by the system, yours only needs two, and can control the pump, the boiler fire up control, the thermostats, etc. etc. etc. Now please understand that the motor will turn continuously until the power is switched off by some other controller. --- http://www.basecuritysystems.no-ip.com Outgoing mail is certified Virus Free. Checked by AVG anti-virus system (http://www.grisoft.com). Version: 6.0.520 / Virus Database: 318 - Release Date: 18/09/03 |
#16
|
|||
|
|||
GSH & HW. novice questions .pls help
"Ebodski" wrote in message ... I was lead to believe on Ed Sirett's post that the microswitch stopped the motor ( i.e. tripped something that stopped supplying power to the motor ). If the motor doesn't get power then the spring return closes it. You're inferring that the switch does something else and the motor is permanently energised as long as my water+heat switch is toggled. So does this mean that throught winter, the motor is energized as long as the heating is switched on. I thought a permanently energized motor which wasn't rotating would just consume power and eventually burn out.. These motors are designed to work in this fashion. They do eventually burn out, but it can take many years. Okay, then back to the drawing board with my wiring sketch :- http://freespace.virgin.net/ian.jarvo/wires.jpg I've confirmed the '?' wire is the HW tank thermosat. This will call for hot water from the boiler, but when timer/programmer is set to call for heating and hot water, this 'stat will be over riden by the switched live from the motoried valve. That's according to your wiring diagram anyway. If the microswitch does not de-energise the synchron motor, then the only way I can read this wiring sketch is that when the motor is energised by the W+H switch, the motor should turn to open the valve ...( this still confuses me as I've still got it in my head that the quadrant is closing the valve ) .If I try to trace the locic of the wires in my sketch, then it seems the black wire becomes live and this energizes the pump & GCV. Power is taken from the timer/programmer to the valve motor which begins to turn the cog wheel in the valve. When the pre-set limit is reached on the cog wheel a little tag presses the micro-switch and switches a Live supply to another appliance in the system. So only one of the wires to the micro-switch will have a constant Live supply which is then switched by the micro-switch to turn something else in the system on. It can be used to turn on a relay, a pump, another valve, the gas flow valve in the boiler, etc. etc. etc. |
#17
|
|||
|
|||
GSH & HW. novice questions .pls help
Okay, I think I've got the jist.
Can I got back to a question that nobody has conclusivley answered. Should my pump have any other way of tripping off/on other than the timer ? Like I keep saying, the pump is running all the time the system is switched on, and in either water-only & heat&water modes. I thought that in summer, if I selected water-only then the pump need not run. And finally my question about zone valve quadrant operational movement of 30°. Is that enough ? |
#18
|
|||
|
|||
GSH & HW. novice questions .pls help
"Ebodski" wrote in message ... Okay, I think I've got the jist. Can I got back to a question that nobody has conclusivley answered. Should my pump have any other way of tripping off/on other than the timer ? Like I keep saying, the pump is running all the time the system is switched on, and in either water-only & heat&water modes. I thought that in summer, if I selected water-only then the pump need not run. Your hot water needs the pump to circulate heated water around the coil in the cylinder and will run any time you call for heat or hot water or both. Your system will be very inefficient if you allow it to be differentially circulated and would probably take about three days to heat a tank full of hot water. And finally my question about zone valve quadrant operational movement of 30°. Is that enough ? YES !!! The activator arm only has to swing about thirty degrees to move the rubber ball away from the opening of the valve outlet and is also enough to move the little tag to activate the micro-switch. |
#19
|
|||
|
|||
GSH & HW. novice questions .pls help
BigWallop wrote:
"Ebodski" wrote in message ... I was lead to believe on Ed Sirett's post that the microswitch stopped the motor ( i.e. tripped something that stopped supplying power to the motor ). Which post was that, or do you mean something in the main FAQ? -- Ed Sirett - Property maintainer and registered gas fitter. The FAQ for uk.diy is at www.diyfaq.org.uk Gas fitting FAQ http://www.makewrite.demon.co.uk/GasFitting.html Sealed CH FAQ http://www.makewrite.demon.co.uk/SealedCH.html |
#20
|
|||
|
|||
GSH & HW. novice questions .pls help
You said on 19/09 :-
A synchron motor, as with any standard motor, will continue to turn when energised until told to stop by some kind of switching system. The small micro-switch in the motorised valve is such a system According to what BW has said. the motor isn't told to stop by the microswitch, it stays energised as long as the 'W+H' switch is toggled. The microswitch doesn't stop the motor, it activates the pump & gas ctrl valve. Pls check my wiring sketch link from the older posts and if you see ethings differently then pls advise.. Thx "Ed Sirett" wrote in message ... BigWallop wrote: "Ebodski" wrote in message ... I was lead to believe on Ed Sirett's post that the microswitch stopped the motor ( i.e. tripped something that stopped supplying power to the motor ). Which post was that, or do you mean something in the main FAQ? -- Ed Sirett - Property maintainer and registered gas fitter. The FAQ for uk.diy is at www.diyfaq.org.uk Gas fitting FAQ http://www.makewrite.demon.co.uk/GasFitting.html Sealed CH FAQ http://www.makewrite.demon.co.uk/SealedCH.html |
#21
Posted to uk.d-i-y
|
|||
|
|||
GSH & HW. novice questions .pls help
ZHAOWEI Product---Small Gear Reducer
The purpose of a ZHAOWEI gear reducer is to increase the available torque output from a motor while decreasing its output speed. Using a ZHAOWEI gear reducer has many advantages. A ZHAOWEI gear reducer can be coupled to a wide variety of motors, therefore a customer's application is no longer limited by the availability of a particular brand of motor. Another advantage is that expensive motors can be replaced with smaller, less expensive motors and a ZHAOWEI gear reducer, resulting in a considerable cost savings and (in most cases) an increase in usable power. Also, replacement parts for ZHAOWEI gear reducers are readily available and in most cases can be shipped the same day they are ordered. ZHAOWEI gear reducers can be used in a multitude of applications wherever there is a requirement for high torque/low speed output, including smart home & household application, medical devices, industry equipments and automobile, etc. Company: Shenzhen ZHAOWEI Machinery & Electronics Co., Ltd URL: http://www.zwgearbox.com/ Contact: Annie Liu Tel:+86-755-27322652 Fax:+86-755-27323949 Add: Blk. 18, Longwangmiao Industry Park, Fuyong Tn., Baoan Dist., Shenzhen 518103, Guangdong, China |
Reply |
Thread Tools | Search this Thread |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Forum | |||
GSH & HW. novice questions .pls help | UK diy | |||
Questions regarding shower installation... | UK diy | |||
Bog standard building regs questions | UK diy | |||
Making bookshelves questions: | UK diy | |||
Unvented HW & CH System Questions | UK diy |