Hi Guys,

I have been checking the FAQ's and Google for information and opinions on
Lagun Republic lathes. I am asking for advice and opinions from the members
of this group. I currently own a South Bend Heave 10. I am a hobbyist and
enjoy having quality machinery. I have looked for quite a while for used
Monarch's (10EE) without much success. The machines I came across needed
too much work and quite frankly, I was intimidated by the electrics and the
problems associated with them.

I read this group religiously and am amazed at the wealth of knowledge that
people are willing to share. I am also confused by the many opinions
expressed about the various lathe manufacturers. It seems that everyone has
a favorite brand or model lathe and for the neophyte it can be quite
confusing. Some love LeBlonds others hate them and that seems to be the
case for most lathes.

I went to a used machinery dealer recently and he had a Lagun/Republic lathe
that he uses in his shop. He likes the machine a lot. It looks like a
Clausing Colchester copy. I was impressed since he has many brand lathes in
his shop but he chose this one for his use. It is an inch/metric machine.

Any advice or comments are sincerely appreciated.

Joe..

"JB" wrote in message
...
Hi Guys,

I have been checking the FAQ's and Google for information and opinions on
Lagun Republic lathes. I am asking for advice and opinions from the
members of this group. I currently own a South Bend Heave 10. I am a
hobbyist and enjoy having quality machinery. I have looked for quite a
while for used Monarch's (10EE) without much success. The machines I came
across needed too much work and quite frankly, I was intimidated by the
electrics and the problems associated with them.

I read this group religiously and am amazed at the wealth of knowledge
that people are willing to share. I am also confused by the many opinions
expressed about the various lathe manufacturers. It seems that everyone
has a favorite brand or model lathe and for the neophyte it can be quite
confusing. Some love LeBlonds others hate them and that seems to be the
case for most lathes.

I went to a used machinery dealer recently and he had a Lagun/Republic
lathe that he uses in his shop. He likes the machine a lot. It looks
like a Clausing Colchester copy. I was impressed since he has many brand
lathes in his shop but he chose this one for his use. It is an
inch/metric machine.

Any advice or comments are sincerely appreciated.

Lots of good info on Monarch lathes at the Practical Machinist web site,
which is a web-based forum and has searchable archives.

Google should find it pretty easily.

Mike

Hey Joe,

Only seen two that I recall. Both seemed OK, certainly much better
quality than say a Grizzly or other like that, but not as nice as
maybe a TOS. Lots of Lagun mills around, and they rate better than an
actual Bridgeport.

Take care/

Brian Lawson,
Bothwell, Ontario.
XXXXXXXXXXXXXXXXXXXXX
On Sat, 8 Oct 2005 12:02:30 -0400, "JB" wrote:

Hi Guys,

I have been checking the FAQ's and Google for information and opinions on
Lagun Republic lathes. I am asking for advice and opinions from the members
of this group. I currently own a South Bend Heave 10. I am a hobbyist and
enjoy having quality machinery. I have looked for quite a while for used
Monarch's (10EE) without much success. The machines I came across needed
too much work and quite frankly, I was intimidated by the electrics and the
problems associated with them.

I read this group religiously and am amazed at the wealth of knowledge that
people are willing to share. I am also confused by the many opinions
expressed about the various lathe manufacturers. It seems that everyone has
a favorite brand or model lathe and for the neophyte it can be quite
confusing. Some love LeBlonds others hate them and that seems to be the
case for most lathes.

I went to a used machinery dealer recently and he had a Lagun/Republic lathe
that he uses in his shop. He likes the machine a lot. It looks like a
Clausing Colchester copy. I was impressed since he has many brand lathes in
his shop but he chose this one for his use. It is an inch/metric machine.

Any advice or comments are sincerely appreciated.

Joe..

On Sat, 8 Oct 2005 12:02:30 -0400, "JB" wrote:

Hi Guys,

I have been checking the FAQ's and Google for information and opinions on
Lagun Republic lathes. I am asking for advice and opinions from the members
of this group. I currently own a South Bend Heave 10. I am a hobbyist and
enjoy having quality machinery. I have looked for quite a while for used
Monarch's (10EE) without much success. The machines I came across needed
too much work and quite frankly, I was intimidated by the electrics and the
problems associated with them.

I read this group religiously and am amazed at the wealth of knowledge that
people are willing to share. I am also confused by the many opinions
expressed about the various lathe manufacturers. It seems that everyone has
a favorite brand or model lathe and for the neophyte it can be quite
confusing. Some love LeBlonds others hate them and that seems to be the
case for most lathes.

I went to a used machinery dealer recently and he had a Lagun/Republic lathe
that he uses in his shop. He likes the machine a lot. It looks like a
Clausing Colchester copy. I was impressed since he has many brand lathes in
his shop but he chose this one for his use. It is an inch/metric machine.

Any advice or comments are sincerely appreciated.

Joe..

Decent lathes. Most are Taiwanese..some are Chinese. However..they are
made very well, for the commercial manufacturing industry, so are
lightyears ahead of a "consumer" lathe .

I would rather own a Lagun knee mill, than any bridgeport.

Gunner

Confronting Liberals with the facts of reality is very much akin to
clubbing baby seals. It gets boring after a while, but because Liberals are
so stupid it is easy work." Steven M. Barry

Thanks Gunner. I appreciate you sharing your sentiments. I continue to
read previous posts on Google. Opinions are all over the board in regards
to Asian import lathes and mills.

Joe..
"Gunner" wrote in message
...
On Sat, 8 Oct 2005 12:02:30 -0400, "JB" wrote:

Hi Guys,

I have been checking the FAQ's and Google for information and opinions on
Lagun Republic lathes. I am asking for advice and opinions from the
members
of this group. I currently own a South Bend Heave 10. I am a hobbyist
and
enjoy having quality machinery. I have looked for quite a while for used
Monarch's (10EE) without much success. The machines I came across needed
too much work and quite frankly, I was intimidated by the electrics and
the
problems associated with them.

I read this group religiously and am amazed at the wealth of knowledge
that
people are willing to share. I am also confused by the many opinions
expressed about the various lathe manufacturers. It seems that everyone
has
a favorite brand or model lathe and for the neophyte it can be quite
confusing. Some love LeBlonds others hate them and that seems to be the
case for most lathes.

I went to a used machinery dealer recently and he had a Lagun/Republic
lathe
that he uses in his shop. He likes the machine a lot. It looks like a
Clausing Colchester copy. I was impressed since he has many brand lathes
in
his shop but he chose this one for his use. It is an inch/metric machine.

Any advice or comments are sincerely appreciated.

Joe..

Decent lathes. Most are Taiwanese..some are Chinese. However..they are
made very well, for the commercial manufacturing industry, so are
lightyears ahead of a "consumer" lathe .

I would rather own a Lagun knee mill, than any bridgeport.

Gunner

Confronting Liberals with the facts of reality is very much akin to
clubbing baby seals. It gets boring after a while, but because Liberals
are
so stupid it is easy work." Steven M. Barry

I would be very wary of any used machinery or used car dealer that told you
that one is his favorite.
gary


"JB" wrote in message
...
Hi Guys,

I have been checking the FAQ's and Google for information and opinions on
Lagun Republic lathes. I am asking for advice and opinions from the
members of this group. I currently own a South Bend Heave 10. I am a
hobbyist and enjoy having quality machinery. I have looked for quite a
while for used Monarch's (10EE) without much success. The machines I came
across needed too much work and quite frankly, I was intimidated by the
electrics and the problems associated with them.

I read this group religiously and am amazed at the wealth of knowledge
that people are willing to share. I am also confused by the many opinions
expressed about the various lathe manufacturers. It seems that everyone
has a favorite brand or model lathe and for the neophyte it can be quite
confusing. Some love LeBlonds others hate them and that seems to be the
case for most lathes.

I went to a used machinery dealer recently and he had a Lagun/Republic
lathe that he uses in his shop. He likes the machine a lot. It looks
like a Clausing Colchester copy. I was impressed since he has many brand
lathes in his shop but he chose this one for his use. It is an
inch/metric machine.

Any advice or comments are sincerely appreciated.

Joe..

Hi Gary,

In fairness to the dealer, he did not say it was his favorite. He said he
like them a lot. It was my observation that with a shop full of machinery,
he used a Lagun lathe for his needs.

Thanks for the input.

Joe...
"Gary Owens" wrote in message
m...
I would be very wary of any used machinery or used car dealer that told you
that one is his favorite.
gary


"JB" wrote in message
...
Hi Guys,

I have been checking the FAQ's and Google for information and opinions on
Lagun Republic lathes. I am asking for advice and opinions from the
members of this group. I currently own a South Bend Heave 10. I am a
hobbyist and enjoy having quality machinery. I have looked for quite a
while for used Monarch's (10EE) without much success. The machines I
came across needed too much work and quite frankly, I was intimidated by
the electrics and the problems associated with them.

I read this group religiously and am amazed at the wealth of knowledge
that people are willing to share. I am also confused by the many
opinions expressed about the various lathe manufacturers. It seems that
everyone has a favorite brand or model lathe and for the neophyte it can
be quite confusing. Some love LeBlonds others hate them and that seems
to be the case for most lathes.

I went to a used machinery dealer recently and he had a Lagun/Republic
lathe that he uses in his shop. He likes the machine a lot. It looks
like a Clausing Colchester copy. I was impressed since he has many brand
lathes in his shop but he chose this one for his use. It is an
inch/metric machine.

Any advice or comments are sincerely appreciated.

Joe..

Gunner wrote:

Decent lathes. Most are Taiwanese..some are Chinese. However..they are
made very well, for the commercial manufacturing industry, so are
lightyears ahead of a "consumer" lathe .

I would rather own a Lagun knee mill, than any bridgeport.

Gunner

Just out of interest, what's your objection to the Bridgeports? Some day
I want to get a mill, and a Bridgeport was pretty high on my preference
list...

Chris

On Sat, 8 Oct 2005 16:35:37 -0400, "JB" wrote:

Thanks Gunner. I appreciate you sharing your sentiments. I continue to
read previous posts on Google. Opinions are all over the board in regards
to Asian import lathes and mills.

Keep in mind..that the term "Asian Import" is a catch phrase like
"fast food"

As you may well know..Miyano, Mori Seki, Whachoen are all " Aisian
Imports" as is Mitiyoyo

Not all Asian Imports are created alike.

G

Gunner


Joe..
"Gunner" wrote in message
.. .
On Sat, 8 Oct 2005 12:02:30 -0400, "JB" wrote:

Hi Guys,

I have been checking the FAQ's and Google for information and opinions on
Lagun Republic lathes. I am asking for advice and opinions from the
members
of this group. I currently own a South Bend Heave 10. I am a hobbyist
and
enjoy having quality machinery. I have looked for quite a while for used
Monarch's (10EE) without much success. The machines I came across needed
too much work and quite frankly, I was intimidated by the electrics and
the
problems associated with them.

I read this group religiously and am amazed at the wealth of knowledge
that
people are willing to share. I am also confused by the many opinions
expressed about the various lathe manufacturers. It seems that everyone
has
a favorite brand or model lathe and for the neophyte it can be quite
confusing. Some love LeBlonds others hate them and that seems to be the
case for most lathes.

I went to a used machinery dealer recently and he had a Lagun/Republic
lathe
that he uses in his shop. He likes the machine a lot. It looks like a
Clausing Colchester copy. I was impressed since he has many brand lathes
in
his shop but he chose this one for his use. It is an inch/metric machine.

Any advice or comments are sincerely appreciated.

Joe..

Decent lathes. Most are Taiwanese..some are Chinese. However..they are
made very well, for the commercial manufacturing industry, so are
lightyears ahead of a "consumer" lathe .

I would rather own a Lagun knee mill, than any bridgeport.

Gunner

Confronting Liberals with the facts of reality is very much akin to
clubbing baby seals. It gets boring after a while, but because Liberals
are
so stupid it is easy work." Steven M. Barry


Confronting Liberals with the facts of reality is very much akin to
clubbing baby seals. It gets boring after a while, but because Liberals are
so stupid it is easy work." Steven M. Barry

On Sat, 8 Oct 2005 23:23:35 +0000 (UTC), Christopher Tidy
wrote:

Gunner wrote:

Decent lathes. Most are Taiwanese..some are Chinese. However..they are
made very well, for the commercial manufacturing industry, so are
lightyears ahead of a "consumer" lathe .

I would rather own a Lagun knee mill, than any bridgeport.

Gunner

Just out of interest, what's your objection to the Bridgeports? Some day
I want to get a mill, and a Bridgeport was pretty high on my preference
list...

Chris


While the controls are basicly the same..and indeed are in effect
copies of Bridgeports..compared to a much beefier Lagun..a Bridgeport
is Gumby. Much less rigid. And with any miller..rigidity is the key.

A Gorton Mill Master ( 1-22) is still beefier yet, though it has some
issues (like a shorter Z travel) and a lack of parts. Ive used all of
them..own a Gorton, when I could have owned any of them. Shrug..if I
get another..it will likely be a Lagun, simply because of the longer Z
travel and ease in purchasing parts.

In fact..I may have one shortly. Shrug. Depends on if the owner wants
a newer one or not.

Gunner

Confronting Liberals with the facts of reality is very much akin to
clubbing baby seals. It gets boring after a while, but because Liberals are
so stupid it is easy work." Steven M. Barry

On Sat, 08 Oct 2005 21:53:53 GMT, "Gary Owens"
wrote:

I would be very wary of any used machinery or used car dealer that told you
that one is his favorite.
gary

Would that also include if he said a Hardinge HLV-H or a 10EE were his
favorites?

Gunner



"JB" wrote in message
...
Hi Guys,

I have been checking the FAQ's and Google for information and opinions on
Lagun Republic lathes. I am asking for advice and opinions from the
members of this group. I currently own a South Bend Heave 10. I am a
hobbyist and enjoy having quality machinery. I have looked for quite a
while for used Monarch's (10EE) without much success. The machines I came
across needed too much work and quite frankly, I was intimidated by the
electrics and the problems associated with them.

I read this group religiously and am amazed at the wealth of knowledge
that people are willing to share. I am also confused by the many opinions
expressed about the various lathe manufacturers. It seems that everyone
has a favorite brand or model lathe and for the neophyte it can be quite
confusing. Some love LeBlonds others hate them and that seems to be the
case for most lathes.

I went to a used machinery dealer recently and he had a Lagun/Republic
lathe that he uses in his shop. He likes the machine a lot. It looks
like a Clausing Colchester copy. I was impressed since he has many brand
lathes in his shop but he chose this one for his use. It is an
inch/metric machine.

Any advice or comments are sincerely appreciated.

Joe..



Confronting Liberals with the facts of reality is very much akin to
clubbing baby seals. It gets boring after a while, but because Liberals are
so stupid it is easy work." Steven M. Barry

Gunner wrote:
On Sat, 8 Oct 2005 23:23:35 +0000 (UTC), Christopher Tidy
wrote:


Gunner wrote:


Decent lathes. Most are Taiwanese..some are Chinese. However..they are
made very well, for the commercial manufacturing industry, so are
lightyears ahead of a "consumer" lathe .

I would rather own a Lagun knee mill, than any bridgeport.

Gunner

Just out of interest, what's your objection to the Bridgeports? Some day
I want to get a mill, and a Bridgeport was pretty high on my preference
list...

Chris



While the controls are basicly the same..and indeed are in effect
copies of Bridgeports..compared to a much beefier Lagun..a Bridgeport
is Gumby. Much less rigid. And with any miller..rigidity is the key.

A Gorton Mill Master ( 1-22) is still beefier yet, though it has some
issues (like a shorter Z travel) and a lack of parts. Ive used all of
them..own a Gorton, when I could have owned any of them. Shrug..if I
get another..it will likely be a Lagun, simply because of the longer Z
travel and ease in purchasing parts.

In fact..I may have one shortly. Shrug. Depends on if the owner wants
a newer one or not.

Gunner

Thanks for the opinion. I'll bear it in mind if I'm looking for a mill.
When I used a Bridgeport I thought it was a nicely made machine, and
didn't have any problems with accuracy, but then I was machining
aluminium. If I had my own mill I would most likely be machining steel
much of the time. A guy offered me a 60" machine at a good price a few
years back (think it was a Cincinnati) but it seemed a bit big and I
didn't have the cash to buy it there and then.

Best wishes,

Chris

Gunner,

I would rather own a Lagun knee mill, than any bridgeport.

Agreed. I had four LT-2's at my last shop. They all had nice hand flaked
tables and alot of travel.

Do they make them in Taiwan now ?? I think mine were all Spanish

Mark

"Mark Mossberg" wrote in message
...
Gunner,

I would rather own a Lagun knee mill, than any bridgeport.

Agreed. I had four LT-2's at my last shop. They all had nice hand flaked
tables and alot of travel.

Do they make them in Taiwan now ?? I think mine were all Spanish

Mark



There's two large Laguns at the machine shop at work. The fellows there
also told me those were Spanish. I wasn't aware that Laguns were Asian.

"gfulton" wrote in news:2c7b0$43499693$a2276371$920
@ALLTEL.NET:


"Mark Mossberg" wrote in message
...
Gunner,

I would rather own a Lagun knee mill, than any bridgeport.

Agreed. I had four LT-2's at my last shop. They all had nice hand flaked
tables and alot of travel.

Do they make them in Taiwan now ?? I think mine were all Spanish

Mark



There's two large Laguns at the machine shop at work. The fellows there
also told me those were Spanish. I wasn't aware that Laguns were Asian.

They are Spanish.

http://www.lagun.com/history.html


--

Dan

On 10 Oct 2005 00:26:11 GMT, D Murphy wrote:

"gfulton" wrote in news:2c7b0$43499693$a2276371$920
:


"Mark Mossberg" wrote in message
...
Gunner,

I would rather own a Lagun knee mill, than any bridgeport.

Agreed. I had four LT-2's at my last shop. They all had nice hand flaked
tables and alot of travel.

Do they make them in Taiwan now ?? I think mine were all Spanish

Mark



There's two large Laguns at the machine shop at work. The fellows there
also told me those were Spanish. I wasn't aware that Laguns were Asian.

They are Spanish.

http://www.lagun.com/history.html


Ill have to check again..but the last several knee mills I paid any
attention two, were badged Taiwan.

Perhaps they are like Delta products?

Gunner

Confronting Liberals with the facts of reality is very much akin to
clubbing baby seals. It gets boring after a while, but because Liberals are
so stupid it is easy work." Steven M. Barry

I thought Lagun was made in Spain. see:

http://www.lagun.com/history.html

Were some made in China?

Cheers,

Kelley

On Sat, 08 Oct 2005 20:12:40 GMT, Gunner
wrote:

On Sat, 8 Oct 2005 12:02:30 -0400, "JB" wrote:

Hi Guys,

I have been checking the FAQ's and Google for information and opinions on
Lagun Republic lathes. I am asking for advice and opinions from the members
of this group. I currently own a South Bend Heave 10. I am a hobbyist and
enjoy having quality machinery. I have looked for quite a while for used
Monarch's (10EE) without much success. The machines I came across needed
too much work and quite frankly, I was intimidated by the electrics and the
problems associated with them.

I read this group religiously and am amazed at the wealth of knowledge that
people are willing to share. I am also confused by the many opinions
expressed about the various lathe manufacturers. It seems that everyone has
a favorite brand or model lathe and for the neophyte it can be quite
confusing. Some love LeBlonds others hate them and that seems to be the
case for most lathes.

I went to a used machinery dealer recently and he had a Lagun/Republic lathe
that he uses in his shop. He likes the machine a lot. It looks like a
Clausing Colchester copy. I was impressed since he has many brand lathes in
his shop but he chose this one for his use. It is an inch/metric machine.

Any advice or comments are sincerely appreciated.

Joe..

Decent lathes. Most are Taiwanese..some are Chinese. However..they are
made very well, for the commercial manufacturing industry, so are
lightyears ahead of a "consumer" lathe .

I would rather own a Lagun knee mill, than any bridgeport.

Gunner

Confronting Liberals with the facts of reality is very much akin to
clubbing baby seals. It gets boring after a while, but because Liberals are
so stupid it is easy work." Steven M. Barry

On Mon, 10 Oct 2005 18:18:31 -0700, Kelley Mascher
wrote:


I thought Lagun was made in Spain. see:

http://www.lagun.com/history.html

Were some made in China?

Cheers,

Kelley

Evidently some were indeed made in China..according to a post from
someone who contacted Lagun

Gunner

Confronting Liberals with the facts of reality is very much akin to
clubbing baby seals. It gets boring after a while, but because Liberals are
so stupid it is easy work." Steven M. Barry

Gunner wrote in
:

Ill have to check again..but the last several knee mills I paid any
attention two, were badged Taiwan.

Perhaps they are like Delta products?

These days where anything is made is a crapshoot. Several well known
Japanese builders are now making machines in China.

The only reason I know about Lagun is that I saw the factory in Spain. They
are actually in the Basque region which for the most part doesn't consider
itself as a part of Spain. The Basque are an interesting culture to say the
least. At the time I was there gunsmithing was a mandatory course in
school. The Basque region is very industrialized and there are several
machine tool builders in the area (Elgoibar and Eibar). They have a lot of
capability and build some very fine equipment. They also make some of the
best custom shotguns you'll ever lay eyes on, but in very small quantities.

All in all a very pretty part of the world filled with good people and good
food. The pace in the factories is very slow by our standards but the
craftsmanship is very high. I'd go back in a minute if given the chance.


--

Dan