Home |
Search |
Today's Posts |
|
Home Repair (alt.home.repair) For all homeowners and DIYers with many experienced tradesmen. Solve your toughest home fix-it problems. |
Reply |
|
LinkBack | Thread Tools | Display Modes |
#1
Posted to alt.home.repair
|
|||
|
|||
Swivel adaptor for screw bits
I am looking for a swivel adapter that will allow the turning of screws at an angle.
https://imgur.com/gDSc3mP Thanks, Andy |
#2
Posted to alt.home.repair
|
|||
|
|||
Swivel adaptor for screw bits
On 07/25/2019 10:05 PM, A K wrote:
I am looking for a swivel adapter that will allow the turning of screws at an angle. https://imgur.com/gDSc3mP Thanks, Andy Would a flex shaft work for you? https://www.amazon.com/X-Things-Flex.../dp/B075MD3D5C |
#3
Posted to alt.home.repair
|
|||
|
|||
Swivel adaptor for screw bits
On 7/25/19 11:05 PM, A K wrote:
I am looking for a swivel adapter that will allow the turning of screws at an angle. https://imgur.com/gDSc3mP Thanks, Andy Dewalt makes these: https://www.homedepot.com/p/DEWALT-1-4-in-Hex-MAXFIT-Pivot-Holder-DWAPVTMF/205997269 |
#4
Posted to alt.home.repair
|
|||
|
|||
Swivel adaptor for screw bits
On 7/26/19 12:05 AM, A K wrote:
I am looking for a swivel adapter that will allow the turning of screws at an angle. https://imgur.com/gDSc3mP Thanks, Andy Ball End Hex Drivers are about the only ones that actually work worth a ****. https://www.amazon.com/Balldriver-Po.../dp/B07KJLHR3Q |
#5
Posted to alt.home.repair
|
|||
|
|||
Swivel adaptor for screw bits
Dean Hoffman posted for all of us...
On 7/25/19 11:05 PM, A K wrote: I am looking for a swivel adapter that will allow the turning of screws at an angle. https://imgur.com/gDSc3mP Thanks, Andy Dewalt makes these: https://www.homedepot.com/p/DEWALT-1-4-in-Hex-MAXFIT-Pivot-Holder-DWAPVTMF/205997269 Thanks Dean, was not aware of these. I have found the flex shafts to be troublesome and the others at fixed angle of 45 or 90 deg just do not cut it. -- Tekkie |
#6
Posted to alt.home.repair
|
|||
|
|||
Swivel adaptor for screw bits
Snake Dawg posted for all of us...
On 7/26/19 12:05 AM, A K wrote: I am looking for a swivel adapter that will allow the turning of screws at an angle. https://imgur.com/gDSc3mP Thanks, Andy Ball End Hex Drivers are about the only ones that actually work worth a ****. https://www.amazon.com/Balldriver-Po.../dp/B07KJLHR3Q I do not believe they will fit in a Philips type head which I presume the OP was referring to. -- Tekkie |
#7
Posted to alt.home.repair
|
|||
|
|||
Swivel adaptor for screw bits
On Fri, 26 Jul 2019 16:18:23 -0400, Tekkie®
wrote: Dean Hoffman posted for all of us... On 7/25/19 11:05 PM, A K wrote: I am looking for a swivel adapter that will allow the turning of screws at an angle. https://imgur.com/gDSc3mP Thanks, Andy Dewalt makes these: https://www.homedepot.com/p/DEWALT-1-4-in-Hex-MAXFIT-Pivot-Holder-DWAPVTMF/205997269 Thanks Dean, was not aware of these. I have found the flex shafts to be troublesome and the others at fixed angle of 45 or 90 deg just do not cut it. Should work at least a few times - if you can hold it well enough to keep the bit square in the screw head without camming out. and if the required angle is less than 21 degrees - - - - |
#8
Posted to alt.home.repair
|
|||
|
|||
Swivel adaptor for screw bits
On Fri, 26 Jul 2019 17:13:50 -0400, Clare Snyder
wrote: On Fri, 26 Jul 2019 16:18:23 -0400, Tekkie® wrote: Dean Hoffman posted for all of us... On 7/25/19 11:05 PM, A K wrote: I am looking for a swivel adapter that will allow the turning of screws at an angle. https://imgur.com/gDSc3mP Thanks, Andy Dewalt makes these: https://www.homedepot.com/p/DEWALT-1-4-in-Hex-MAXFIT-Pivot-Holder-DWAPVTMF/205997269 Thanks Dean, was not aware of these. I have found the flex shafts to be troublesome and the others at fixed angle of 45 or 90 deg just do not cut it. Should work at least a few times - if you can hold it well enough to keep the bit square in the screw head without camming out. and if the required angle is less than 21 degrees - - - - And apparently changing the bits is a royal PITA too - you pretty much need a vice-grips or two. |
#9
Posted to alt.home.repair
|
|||
|
|||
Swivel adaptor for screw bits
On 7/26/2019 4:21 PM, Tekkie® wrote:
Snake Dawg posted for all of us... On 7/26/19 12:05 AM, A K wrote: I am looking for a swivel adapter that will allow the turning of screws at an angle. https://imgur.com/gDSc3mP Thanks, Andy Ball End Hex Drivers are about the only ones that actually work worth a ****. https://www.amazon.com/Balldriver-Po.../dp/B07KJLHR3Q I do not believe they will fit in a Philips type head which I presume the OP was referring to. I see no mention of phillips.Â* Did you just pull that out of your ass? |
#10
Posted to alt.home.repair
|
|||
|
|||
Swivel adaptor for screw bits
On 7/26/19 4:57 PM, Mike Oxbern wrote:
On 7/26/2019 4:21 PM, Tekkie® wrote: Snake Dawg posted for all of us... On 7/26/19 12:05 AM, A K wrote: I am looking for a swivel adapter that will allow the turning of screws at an angle. https://imgur.com/gDSc3mP Thanks, Â*Â*Â*Â*Â*Â*Â*Â*Â*Â*Â*Â* Andy Ball End Hex Drivers are about the only ones that actually work worth a ****. https://www.amazon.com/Balldriver-Po.../dp/B07KJLHR3Q I do not believe they will fit in a Philips type head which I presume the OP was referring to. I see no mention of phillips.Â* Did you just pull that out of your ass? That's what is in the OP's picture. |
#11
Posted to alt.home.repair
|
|||
|
|||
Swivel adaptor for screw bits
On Friday, July 26, 2019 at 12:04:52 AM UTC-5, rbowman wrote:
On 07/25/2019 10:05 PM, A K wrote: I am looking for a swivel adapter that will allow the turning of screws at an angle. https://imgur.com/gDSc3mP Thanks, Andy Would a flex shaft work for you? https://www.amazon.com/X-Things-Flex.../dp/B075MD3D5C Yes. Thanks rbowman. |
#12
Posted to alt.home.repair
|
|||
|
|||
Swivel adaptor for screw bits
On Friday, July 26, 2019 at 3:21:24 PM UTC-5, Tekkie® wrote:
Snake Dawg posted for all of us... On 7/26/19 12:05 AM, A K wrote: I am looking for a swivel adapter that will allow the turning of screws at an angle. https://imgur.com/gDSc3mP Thanks, Andy Ball End Hex Drivers are about the only ones that actually work worth a ****. https://www.amazon.com/Balldriver-Po.../dp/B07KJLHR3Q I do not believe they will fit in a Philips type head which I presume the OP was referring to. -- Tekkie Thanks. I think this will work. https://www.amazon.com/AUTOTOOLHOME-...gateway&sr=8-7 I am more interested in the shorter length. Andy |
Reply |
Thread Tools | Search this Thread |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Forum | |||
Making an Adaptor from the vintage single wire 5/8" screw on MIC connector to BNC | Electronics Repair | |||
(again?) screw into light socket: male--SWIVEL--female (for pointable floodlight) | Home Repair | |||
I need a swivel or bearing for a lazy susan style turntable. | Woodworking | |||
I need a swivel or bearing for a lazy susan style turnta | Woodworking | |||
Screw-in photo cell light adaptor | Home Repair |