I have a B&W 5" CTR Nexxtech TV, model 1612002 (used as a lobby monitor),
which when switched on, only displays the top half of the picture normally,
while the bottom half is squashed into a narrow bright horizontal band.

You can sort of make out that the rest (bottom) of the picture is upside
down. After it's been on for a while, the bottom half starts to extend
further down, and becomes right side up, but is still squashed, so a 1/4
of the screen remains blank. Other than the brightness and V-hold, there
are no other adjustments inside or outside.

Does anyone have any ideas where to look for the reason for this? I have an
electrical background (not with TVs though), so replacing parts would not be
a problem. Any hints would be appreciated. -Rick

On Thursday, November 14, 2013 6:14:33 PM UTC-8, Rick wrote:
I have a B&W 5" CTR Nexxtech TV, model 1612002 (used as a lobby monitor),

which when switched on, only displays the top half of the picture normally,

while the bottom half is squashed into a narrow bright horizontal band.



You can sort of make out that the rest (bottom) of the picture is upside

down. After it's been on for a while, the bottom half starts to extend

further down, and becomes right side up, but is still squashed, so a 1/4

of the screen remains blank. Other than the brightness and V-hold, there

are no other adjustments inside or outside.



Does anyone have any ideas where to look for the reason for this? I have an

electrical background (not with TVs though), so replacing parts would not be

a problem. Any hints would be appreciated. -Rick

You almost certainly have a dried out capacitor in the vertical deflection amplifier. Just a guess but I bet it's 1000 to 2200 uF very near the vertical amp. This happens all the time with Sony CRT monitors.

G²

"Rick"


Does anyone have any ideas where to look for the reason for this? I have
an
electrical background (not with TVs though), so replacing parts would not
be
a problem.


** No one familiar with electronics calls what they do "electrical".

So what is your "background" actually in ?

What if any test gear do you have ?

Access to any components like ICs and electros that might be found in a
CRT TV set ?



.... Phil

wrote in messagea problem.

You almost certainly have a dried out capacitor in the vertical
deflection amplifier. Just a guess but I bet it's 1000 to 2200 uF
very near the vertical amp. This happens all the time with Sony
CRT monitors.
G²

Thanks, G², greatly appreciated!

"Phil Allison" wrote
** No one familiar with electronics calls what they do "electrical".
So what is your "background" actually in ?
What if any test gear do you have ?
Access to any components like ICs and electros that might be found in a
CRT TV set ?
.... Phil

Ok I'll bite. "No one" wouldn't neccessarily include those where
English is their second language.
My "background" is an electromechanical Journeyman / Apprenticeship
- not sure what the English equivalent is.
I have owned a variety of test gear, including a scope.

I have fixed or *modified* dozens of VCRs (Beta, SVHS, Hi8), the odd
TV, lots of communication-types of radios, and done some minor surface
component work.

Time is valuable -- particularly when TVs are not your specialty,
so just trying to get some ideas from those who deal with that sort of
thing on a regular basis.

No offence taken though, Phil, you provide a lot of valuable input
otherwise.

On 11/15/2013 7:25 AM, Rick wrote:
wrote in messagea problem.

You almost certainly have a dried out capacitor in the vertical
deflection amplifier. Just a guess but I bet it's 1000 to 2200 uF
very near the vertical amp. This happens all the time with Sony
CRT monitors.
G²

Thanks, G², greatly appreciated!



Check the vertical deflection driver if new caps (use good quality 105C
ones of course!) don't fix the problem.

Use low ESR caps for anything on the horizontal circuit, check the other
electrolytic caps using an ESR meter like the blue Bob Robert ESR meter
kit one that we sell.

We've also replaced a lot of the associated deflection transistors in
vertical circuits when the cap failed...

John :-#)#

--
(Please post followups or tech inquiries to the newsgroup)
John's Jukes Ltd. 2343 Main St., Vancouver, BC, Canada V5T 3C9
(604)872-5757 or Fax 872-2010 (Pinballs, Jukes, Video Games)
www.flippers.com
"Old pinballers never die, they just flip out."

My experience with CRT type tv's and monitors over the past 40 years has been about 75% of the time bad electrolytic capacitors have been the cause of problems. The other 25% of the time it has been solid state components like transistors, IC's, diodes, etc causing troubles.

In your case I think the first place to look is at any electrolytic capacitors in the vertical deflection stage. There might be an obvious bad one with a bulged/blown out top or leaking out the bottom of it. Naturally, a capacitor meter would be a big help in testing the capacitors and finding an electrically bad one.

The vertical output stage may either have a pair of transistors (one operates the top half of the picture and the other operates the bottom half) running it or it could have the vertical output stage combined in a single integrated circuit which is usually bolted to a heat sink to keep it cool.

Forgot to mention, likely capacitors causing your problem could be ones either rated at 1000 to 2200 uf (around 10 to 25 volts) or look for any that are rated at a small uf like 3.3 uf but at higher voltage like say for instance 160 volts.

I had one of those Harbor Freight 5" B&W security camera monitors with a "no vertical deflection" symptom and it turned out to have two bad electrolytic capacitors: a 2200 uf @ 10 volts and a 3.3 uf @ 160 volts. Replacing them restored the monitor back to full operation again.

"Rick"

"Phil Allison"

** No one familiar with electronics calls what they do "electrical".

So what is your "background" actually in ?

What if any test gear do you have ?

Access to any components like ICs and electros that might be found in a
CRT TV set ?

.... Phil

Ok I'll bite. "No one" wouldn't necessarily include those where
English is their second language.


** Yes it would.

My "background" is an electromechanical Journeyman / Apprenticeship
- not sure what the English equivalent is.

** Electrical technician.


I have owned a variety of test gear, including a scope.

** Past tense ?


I have fixed or *modified* dozens of VCRs (Beta, SVHS, Hi8),

** Mechanical work - right ?


Time is valuable -- particularly when TVs are not your specialty,
so just trying to get some ideas from those who deal with that sort of
thing on a regular basis.

** CRT sets are past tense - nobody fixes them.

No offence taken though, Phil, you provide a lot of valuable input
otherwise.

** Others have posted the only advice possible.

Did you really think someone here KNEW that obscure TV ?


.... Phil

My experience - boost capacitor, often about 100uF at 35 volts, near the
vertical output IC.

Mark Z.

If this happened suddenly (one minute full deflection, the next half pix), it's most likely not a capacitor, at least not the only problem.

If it uses an IC for vertical deflection, it it most likely bad or can even have cracked solder along the pins. Try defluxing the pins thoroughly, then resolder with quality solder. If it runs OK, leave as is. Cracked solder is a function of age, heat, and vibration.

If the IC or discrete output transistors is\are bad, replace it and ESR every electrolytic in the circuit. A high ESR cap may not cause any initial symptom, but the IC will fail.



On Thursday, November 14, 2013 9:14:33 PM UTC-5, Rick wrote:
I have a B&W 5" CTR Nexxtech TV, model 1612002 (used as a lobby monitor),

which when switched on, only displays the top half of the picture normally,

while the bottom half is squashed into a narrow bright horizontal band.



You can sort of make out that the rest (bottom) of the picture is upside

down. After it's been on for a while, the bottom half starts to extend

further down, and becomes right side up, but is still squashed, so a 1/4

of the screen remains blank. Other than the brightness and V-hold, there

are no other adjustments inside or outside.



Does anyone have any ideas where to look for the reason for this? I have an

electrical background (not with TVs though), so replacing parts would not be

a problem. Any hints would be appreciated. -Rick

On Saturday, November 16, 2013 5:38:02 AM UTC-5, Mark Zacharias wrote:
My experience - boost capacitor, often about 100uF at 35 volts, near the vertical output IC. Mark Z.

Actually, not in my experience. The boost cap or circuit only speeds up the retrace. What the OP described sounds like high ESR in the main output cap, if the unit has one. Because of the inductance of the yoke winding, high ESR acting like a resistor will cause the top of the raster to be still kinda stretched, but the bottom will be compressed because that is the part where it needs the low frequency component of the waveform. The boost cap only causes problems at the top usually.

I think the problem is going to be a large cap, like a 2,200 uF or so.

"If this happened suddenly (..."

Good point. We do not know if the guy just got the thing or what. Almost any problem with the caps comes on gradually. It is quite rare that one goes all the sudden. If it does it is usually completely open or shorted, in either case there would probably be no deflection at all.

Actually a model number might help. I got two databases (paid) with a whole bunch of symcures. A print would be great. The thing might not even have an output coupling cap, which would mean the problem is likely the bottom output. (in IC or not)

On the other hand, the ramp cap associated with the vertical driver can also do that. Sometimes those are tantalum and they can fail just like that on occasion.

Turned out to be a FEC 2200uF / 10V capacitor with no
obvious signs of bulging or leaking. Took only a couple of
minutes to fix, and works great again now!

Thanks G² and everyone else for their input !!

Glad to hear you got it fixed.

On Saturday, November 16, 2013 9:43:37 PM UTC-5, Ken Layton wrote:
Glad to hear you got it fixed.

Yes. Now the argument can start. We can talk about whether it was the Christian Fundamentalists or the JEws who are at fault, or if there is no fault because the thing is 100 years old. Then we can go into the Prussian governemnt's involvment in the current middle east crisis.

But let's not forget about the Russians and their hand in not stopping the tragedy of 9/11 which killed almost as many people as hospitals and drunk drivers combined in a month.

Then there are those socio-economic factors that make most of us not give a **** anymore.

Or we can start picking on Phil Allison. Your call.

On Saturday, November 16, 2013 9:15:26 AM UTC-8, wrote:
"If this happened suddenly (..."



Good point. We do not know if the guy just got the thing or what. Almost any problem with the caps comes on gradually. It is quite rare that one goes all the sudden. If it does it is usually completely open or shorted, in either case there would probably be no deflection at all.



Actually a model number might help. I got two databases (paid) with a whole bunch of symcures. A print would be great. The thing might not even have an output coupling cap, which would mean the problem is likely the bottom output. (in IC or not)



On the other hand, the ramp cap associated with the vertical driver can also do that. Sometimes those are tantalum and they can fail just like that on occasion.

The OP did post the model number in the original post: Nexxtech model 1612002.

wrote:

On Saturday, November 16, 2013 9:43:37 PM UTC-5, Ken Layton wrote:
Glad to hear you got it fixed.

Yes. Now the argument can start.


YAWN

--
Anyone wanting to run for any political office in the US should have to
have a DD214, and a honorable discharge.