I finally got moved into my new house and the machines are nestled into the
garage. I have to move the lathe and bridgeport into the cellar. I have a
walk-in door to the basement but the problem is getting the stuff to the
door. There is about 40' of grass to move the stuff over. I moved the
bridgeport head and table on a skid by using rollers under it. It was quite
a job. I am leery of trying to move the base the same way. Any suggestions
on moving the base ? There is not enough room to get a large machine in to
carry it.

Thanks,

Bill W

The usual method is to get a couple of sheets of plywood and lay one
down, roll the machine along it, place the next one down and roll the
machine onto it, trot around and grab the first one and carry it round
front, etc.

Grant

BW wrote:

I finally got moved into my new house and the machines are nestled into the
garage. I have to move the lathe and bridgeport into the cellar. I have a
walk-in door to the basement but the problem is getting the stuff to the
door. There is about 40' of grass to move the stuff over. I moved the
bridgeport head and table on a skid by using rollers under it. It was quite
a job. I am leery of trying to move the base the same way. Any suggestions
on moving the base ? There is not enough room to get a large machine in to
carry it.

Thanks,

Bill W

Karen Story wrote:

The usual method is to get a couple of sheets of plywood and lay one
down, roll the machine along it, place the next one down and roll the
machine onto it, trot around and grab the first one and carry it round
front, etc.

Right! The only tricky part will be to keep the rollers from dropping down
between the plywood sheets. Having the sheets run at an angle to the
direction
of motion would be a big help. If the ground is really soft, you could
stitch
a 2x4 under each junction, and it would just push into the earth and
allow the
sheets to stay together.

Jon

In article ,
Jon Elson wrote:

Karen Story wrote:

The usual method is to get a couple of sheets of plywood and lay one
down, roll the machine along it, place the next one down and roll the
machine onto it, trot around and grab the first one and carry it round
front, etc.

Right! The only tricky part will be to keep the rollers from dropping down
between the plywood sheets. Having the sheets run at an angle to the
direction
of motion would be a big help. If the ground is really soft, you could
stitch
a 2x4 under each junction, and it would just push into the earth and
allow the
sheets to stay together.

Jon


With the 2x4 you could nail the sheets so there would be no gap to drop
a roller in.

--
Free men own guns, slaves don't
www.geocities.com/CapitolHill/5357/

The usual method is to get a couple of sheets of plywood and lay one

With the 2x4 you could nail the sheets so there would be no gap to drop
a roller in.

You would have a hard time moving the sheet woun"t you.Why not just put the 2nd
sheet under the 1st one ? Ray

In article ,
(SMuel10363) wrote:

The usual method is to get a couple of sheets of plywood and lay one

With the 2x4 you could nail the sheets so there would be no gap to drop
a roller in.

You would have a hard time moving the sheet woun"t you.Why not just put the
2nd
sheet under the 1st one ? Ray

No problem pulling out a few small nails, although I would use screws
myself.

--
Free men own guns, slaves don't
www.geocities.com/CapitolHill/5357/

Jon Elson wrote:



Karen Story wrote:

The usual method is to get a couple of sheets of plywood and lay one
down, roll the machine along it, place the next one down and roll the
machine onto it, trot around and grab the first one and carry it round
front, etc.

Right! The only tricky part will be to keep the rollers from dropping down
between the plywood sheets. Having the sheets run at an angle to the direction
of motion would be a big help. If the ground is really soft, you could stitch
a 2x4 under each junction, and it would just push into the earth and allow the
sheets to stay together.

Just "underlap" the ends of the plywood.

-jc-

"BW" wrote in message ...
I finally got moved into my new house and the machines are nestled into the
garage. I have to move the lathe and bridgeport into the cellar. I have a
walk-in door to the basement but the problem is getting the stuff to the
door. There is about 40' of grass to move the stuff over. I moved the
bridgeport head and table on a skid by using rollers under it. It was quite
a job. I am leery of trying to move the base the same way. Any suggestions
on moving the base ? There is not enough room to get a large machine in to
carry it.

2 lengths of angle iron with the v upwards, supported if needed
(depends on how big the angle iron is, how soft the ground is) with
scrap timber crossties. Then you can either lube the rails & bar the
base along, or use rollers as per flat ground. Done this myself, it
works quite well.

Assumes the ground is reasonably flat/level of course.

PDW

On Tue, 31 Aug 2004 15:59:08 -0400, "BW"
wrote:

I finally got moved into my new house and the machines are nestled into the
garage. I have to move the lathe and bridgeport into the cellar. I have a
walk-in door to the basement but the problem is getting the stuff to the
door. There is about 40' of grass to move the stuff over. I moved the
bridgeport head and table on a skid by using rollers under it. It was quite
a job. I am leery of trying to move the base the same way. Any suggestions
on moving the base ? There is not enough room to get a large machine in to
carry it.

Thanks,

Bill W

Two sheets of 3/4" plywood. Lay the far one under the one the mill is
on. Push to the new sheet, remove the old one, pry up the far end,
stick the new sheet under the one the mill is on, move to this sheet
and repeat. Takes more time to explain than to do.

Gunner

"In my humble opinion, the petty carping levied against Bush by
the Democrats proves again, it is better to have your eye plucked
out by an eagle than to be nibbled to death by ducks." - Norman
Liebmann

On Wed, 01 Sep 2004 03:04:21 GMT, Gunner
wrote:

On Tue, 31 Aug 2004 15:59:08 -0400, "BW"
wrote:

I finally got moved into my new house and the machines are nestled into the
garage. I have to move the lathe and bridgeport into the cellar. I have a
walk-in door to the basement but the problem is getting the stuff to the
door. There is about 40' of grass to move the stuff over. I moved the
bridgeport head and table on a skid by using rollers under it. It was quite
a job. I am leery of trying to move the base the same way. Any suggestions
on moving the base ? There is not enough room to get a large machine in to
carry it.

Thanks,

Bill W

Two sheets of 3/4" plywood. Lay the far one under the one the mill is
on. Push to the new sheet, remove the old one, pry up the far end,
stick the new sheet under the one the mill is on, move to this sheet
and repeat. Takes more time to explain than to do.

Gunner

If I can't come up with three sheets I look to zenith.

The plywood prices are terrible . I use to get large counter tops from
dumpster diving. Their particle board , but 3/4 and laminated on the
other side. After 911 everyone seemed to stop making major screw ups.
I'm sure NAFTA didn't help.

Where are you located? I've got this new knuckle-boom I'm itchin' to
try out and my wife says I can't lift her car up with it!

james, Port Orchard (seattle), Washington, USA, Earth


On Wed, 01 Sep 2004 20:09:26 -0700, Sunworshipper
wrote:

On Wed, 01 Sep 2004 03:04:21 GMT, Gunner
wrote:

On Tue, 31 Aug 2004 15:59:08 -0400, "BW"
wrote:

I finally got moved into my new house and the machines are nestled into the
garage. I have to move the lathe and bridgeport into the cellar. I have a
walk-in door to the basement but the problem is getting the stuff to the
door. There is about 40' of grass to move the stuff over. I moved the
bridgeport head and table on a skid by using rollers under it. It was quite
a job. I am leery of trying to move the base the same way. Any suggestions
on moving the base ? There is not enough room to get a large machine in to
carry it.

Thanks,

Bill W

Two sheets of 3/4" plywood. Lay the far one under the one the mill is
on. Push to the new sheet, remove the old one, pry up the far end,
stick the new sheet under the one the mill is on, move to this sheet
and repeat. Takes more time to explain than to do.

Gunner

If I can't come up with three sheets I look to zenith.

The plywood prices are terrible . I use to get large counter tops from
dumpster diving. Their particle board , but 3/4 and laminated on the
other side. After 911 everyone seemed to stop making major screw ups.
I'm sure NAFTA didn't help.

On Thu, 02 Sep 2004 04:51:40 -0700, RainLover
wrote:

Where are you located? I've got this new knuckle-boom I'm itchin' to
try out and my wife says I can't lift her car up with it!

Is that Can't (as in 'NO, and that's FINAL!'), or Can't (as in 'You
don't have the proper straps, rigging and spreader bars yet, you might
scratch the paint Honey Dear...')?

If it was the second answer, does she have a single sister? ;-P

-- Bruce --
--
Bruce L. Bergman, Woodland Hills (Los Angeles) CA - Desktop
Electrician for Westend Electric - CA726700
5737 Kanan Rd. #359, Agoura CA 91301 (818) 889-9545
Spamtrapped address: Remove the python and the invalid, and use a net.

Sorry, I am in Massachusetts.

The plywood sounds good. I've got the base on a new skid that I built and
I'll get the plywood today and give it a go.

Thanks,

BW
"RainLover" wrote in message
...
Where are you located? I've got this new knuckle-boom I'm itchin' to
try out and my wife says I can't lift her car up with it!

james, Port Orchard (seattle), Washington, USA, Earth


On Wed, 01 Sep 2004 20:09:26 -0700, Sunworshipper
wrote:

On Wed, 01 Sep 2004 03:04:21 GMT, Gunner
wrote:

On Tue, 31 Aug 2004 15:59:08 -0400, "BW"
wrote:

I finally got moved into my new house and the machines are nestled into
the
garage. I have to move the lathe and bridgeport into the cellar. I have
a
walk-in door to the basement but the problem is getting the stuff to
the
door. There is about 40' of grass to move the stuff over. I moved the
bridgeport head and table on a skid by using rollers under it. It was
quite
a job. I am leery of trying to move the base the same way. Any
suggestions
on moving the base ? There is not enough room to get a large machine in
to
carry it.

Thanks,

Bill W

Two sheets of 3/4" plywood. Lay the far one under the one the mill is
on. Push to the new sheet, remove the old one, pry up the far end,
stick the new sheet under the one the mill is on, move to this sheet
and repeat. Takes more time to explain than to do.

Gunner

If I can't come up with three sheets I look to zenith.

The plywood prices are terrible . I use to get large counter tops from
dumpster diving. Their particle board , but 3/4 and laminated on the
other side. After 911 everyone seemed to stop making major screw ups.
I'm sure NAFTA didn't help.

RainLover wrote:
Where are you located? I've got this new knuckle-boom I'm itchin' to
try out and my wife says I can't lift her car up with it!

Come on over to Issaquah! I'm moving in about a month and I've got a
lathe that prolly weighs more than your wife's car that needs to be
stuffed into a truck or something..

Oh, and here's the secret phrase you must learn in dealing with your
wife on these matters: "Hey, what can go wrong?!"

Sometimes, this is followed shortly thereafter with another magical,
secret phrase: "Hey, who knew?!" ;-)
--
Doug
http://www.des.indianchief.com/index.htm

On Thu, 02 Sep 2004 16:13:15 GMT, Doug Smith
wrote:

RainLover wrote:
Where are you located? I've got this new knuckle-boom I'm itchin' to
try out and my wife says I can't lift her car up with it!

Come on over to Issaquah! I'm moving in about a month and I've got a
lathe that prolly weighs more than your wife's car that needs to be
stuffed into a truck or something..

Oh, and here's the secret phrase you must learn in dealing with your
wife on these matters: "Hey, what can go wrong?!"

Sometimes, this is followed shortly thereafter with another magical,
secret phrase: "Hey, who knew?!" ;-)


"hey, hold my beer and watch this!"

Gunner

"In my humble opinion, the petty carping levied against Bush by
the Democrats proves again, it is better to have your eye plucked
out by an eagle than to be nibbled to death by ducks." - Norman
Liebmann

On Thu, 02 Sep 2004 16:13:15 GMT, Doug Smith
wrote:

RainLover wrote:
Where are you located? I've got this new knuckle-boom I'm itchin' to
try out and my wife says I can't lift her car up with it!

Come on over to Issaquah! I'm moving in about a month and I've got a
lathe that prolly weighs more than your wife's car that needs to be
stuffed into a truck or something..

Oh, and here's the secret phrase you must learn in dealing with your
wife on these matters: "Hey, what can go wrong?!"

Sometimes, this is followed shortly thereafter with another magical,
secret phrase: "Hey, who knew?!" ;-)

Don't tell me, you Consider the Red Green show to be a Religion? LOL

I'd move it, but you'd have to pay for gas and ferry to get me there
and back! What's your guess on its weight?

James, Port Orchard.

Thanks for the ideas. What I finally used was 2x4 tracks. Rather than spend
the money for 3/4 ply, I made 2 sets of tracks out of old 2x4's that I had
left over from a framing project. I then used 2" steel pipes under the base
and moved the spare track as the base moved onto the next track. Other than
having to pay close attention
to keeping it centered, it worked great and the cost was minimal.

"BW" wrote in message
...
I finally got moved into my new house and the machines are nestled into
the
garage. I have to move the lathe and bridgeport into the cellar. I have a
walk-in door to the basement but the problem is getting the stuff to the
door. There is about 40' of grass to move the stuff over. I moved the
bridgeport head and table on a skid by using rollers under it. It was
quite
a job. I am leery of trying to move the base the same way. Any suggestions
on moving the base ? There is not enough room to get a large machine in to
carry it.

Thanks,

Bill W