Home |
Search |
Today's Posts |
|
Home Repair (alt.home.repair) For all homeowners and DIYers with many experienced tradesmen. Solve your toughest home fix-it problems. |
Reply |
|
LinkBack | Thread Tools | Display Modes |
#1
Posted to alt.home.repair
|
|||
|
|||
New decking boards over old?
I need to replace the surface on my 200 ft sq deck here in SC. Can I
just nail/screw new deck treated/composite boards over the 27 year old treated ones (maybe at a 45 or 90 degree angle), or do I need to remove the old ones first? Jerry |
#2
Posted to alt.home.repair
|
|||
|
|||
New decking boards over old?
Yeah that would be a lot easier, pulled and replaced mine a couple of years
ago. Mine were too warped to go this way. Just get a big pry bar and pull the old boards up. I'm sure you will be a lot happier with the result. Fortunately it's a job you can do piecemeal. Good luck "Jerry" wrote in message ... I need to replace the surface on my 200 ft sq deck here in SC. Can I just nail/screw new deck treated/composite boards over the 27 year old treated ones (maybe at a 45 or 90 degree angle), or do I need to remove the old ones first? Jerry |
#3
Posted to alt.home.repair
|
|||
|
|||
New decking boards over old?
pull them all up, and inspect everything below, with 27 year old joists
you might have some bad ones. |
#4
Posted to alt.home.repair
|
|||
|
|||
New decking boards over old?
"Jerry" wrote in message ... I need to replace the surface on my 200 ft sq deck here in SC. Can I just nail/screw new deck treated/composite boards over the 27 year old treated ones (maybe at a 45 or 90 degree angle), or do I need to remove the old ones first? Jerry Of course you can, but the real question is "should" you do it. I'd say no. First, the deck is not going to be sealed between the layers of boards. Rain will get between the two boards and foster rot and mold. There must be a reason to replace them and that will accelerate the destruction of the new. |
#5
Posted to alt.home.repair
|
|||
|
|||
New decking boards over old?
On Wed, 18 Jan 2006 03:16:10 GMT, "Edwin Pawlowski"
wrote: "Jerry" wrote in message .. . I need to replace the surface on my 200 ft sq deck here in SC. Can I just nail/screw new deck treated/composite boards over the 27 year old treated ones (maybe at a 45 or 90 degree angle), or do I need to remove the old ones first? Jerry Of course you can, but the real question is "should" you do it. I'd say no. First, the deck is not going to be sealed between the layers of boards. Rain will get between the two boards and foster rot and mold. There must be a reason to replace them and that will accelerate the destruction of the new. Not to mention water freezing into ice in winter and lifting the new boards. Remove the old boards, check the framing for bad boards, replace anything that is bad, and install new decking. Maybe you dont need to replace all of them anyhow. Just replace the bad boards. If they are treated, it's likely some if not many of them are still good. If the frame is solid, just replace a few boards at a time. That way you can still use the deck, and not have a big mess. |
Reply |
Thread Tools | Search this Thread |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Forum | |||
Need advice on replacing lap boards | Home Repair | |||
Decking - boards, knots, splits | UK diy | |||
Fiberon decking - no gaps between boards - ideas for fix?? | Home Repair | |||
Use 7/8" boards for decking? | Woodworking | |||
Wooden Floors | UK diy |