Home |
Search |
Today's Posts |
|
Electronics Repair (sci.electronics.repair) Discussion of repairing electronic equipment. Topics include requests for assistance, where to obtain servicing information and parts, techniques for diagnosis and repair, and annecdotes about success, failures and problems. |
Reply |
|
LinkBack | Thread Tools | Display Modes |
#1
Posted to sci.electronics.repair
|
|||
|
|||
Baffled by cordless tool problem
I have a Milwaukee 12v cordless jig saw. It was working fine then
stopped, dead. Then started again, with no symptoms. It did this back & forth a few times, then stayed dead. It never stopped while being used - it just wouldn't start at all. I took it apart to diagnose & as soon as I put it on the battery, it was OK! I reassembled it and periodically tested it over a week. Always OK. Today I put the base/shoe back on & it was dead! As I took it apart again, I kept checking it, but it didn't come back. And then, sitting there, it did come back, spontaneously. It has a small PCB for speed control. The PCB also controls an LED "work light", which comes on when the battery is connected. Except when it's dead - making the LED a good go, no-go indicator. And showing that the problem is more basic than speed-control circuitry. The PCB has a number of wires soldered in through holes. I have checked all of them. I have stressed the board with mild twisting; I've cleaned it with carbon tet; and have warmed it with a hair dryer. Nothing had any effect. The board is SMT (with a 48 pin chip!), except for the wires, 1 cap, and the output FETs, which are TH. Is there anything else that I can try? Thanks, Bob |
#2
Posted to sci.electronics.repair
|
|||
|
|||
Baffled by cordless tool problem
Bob Engelhardt wrote:
I have a Milwaukee 12v cordless jig saw. It was working fine then stopped, dead. Then started again, with no symptoms. It did this back & forth a few times, then stayed dead. It never stopped while being used - it just wouldn't start at all. One bad winding on the motor, a bad spot on the commutator, really worn brushes? (Assuming it's not brushless.) To check: Get it to the dead state again. With your fingers off of the trigger, use a stick of wood or something that's not your fingers to turn the blade a few degrees. Then try the trigger again. If you can reliably make it start that way, look at the brushes and commutator. Matt Roberds |
#3
Posted to sci.electronics.repair
|
|||
|
|||
Baffled by cordless tool problem
|
#4
Posted to sci.electronics.repair
|
|||
|
|||
Baffled by cordless tool problem
On 12/28/2015 6:30 PM, Bob Engelhardt wrote:
On 12/28/2015 7:13 PM, wrote: One bad winding on the motor, a bad spot on the commutator, really worn brushes? (Assuming it's not brushless.) ... When it's dead, even the LED does not come on. Which it normally does even without the trigger being pulled. So it can't be commutator, etc. Intermittent battery connection. Mikek |
#5
Posted to sci.electronics.repair
|
|||
|
|||
Baffled by cordless tool problem
On 12/28/2015 8:22 PM, amdx wrote:
On 12/28/2015 6:30 PM, Bob Engelhardt wrote: On 12/28/2015 7:13 PM, wrote: One bad winding on the motor, a bad spot on the commutator, really worn brushes? (Assuming it's not brushless.) ... When it's dead, even the LED does not come on. Which it normally does even without the trigger being pulled. So it can't be commutator, etc. Intermittent battery connection. Mikek I want to say that I've checked that - that there is voltage on the connector terminals when it was dead. But I've gone around in so many circles that I can't remember if I was even able to do that. I.e., if it was ever dead after I opened it. I have wiggled and stressed the battery connector without consequence. When it dies again, that will the first thing I check. Thanks, Bob |
#6
Posted to sci.electronics.repair
|
|||
|
|||
Baffled by cordless tool problem
On 12/28/2015 10:13 PM, Bob Engelhardt wrote:
On 12/28/2015 8:22 PM, amdx wrote: On 12/28/2015 6:30 PM, Bob Engelhardt wrote: On 12/28/2015 7:13 PM, wrote: One bad winding on the motor, a bad spot on the commutator, really worn brushes? (Assuming it's not brushless.) ... When it's dead, even the LED does not come on. Which it normally does even without the trigger being pulled. So it can't be commutator, etc. Intermittent battery connection. Mikek I want to say that I've checked that - that there is voltage on the connector terminals when it was dead. But I've gone around in so many circles that I can't remember if I was even able to do that. I.e., if it was ever dead after I opened it. I have wiggled and stressed the battery connector without consequence. When it dies again, that will the first thing I check. Thanks, Bob Update: I put it together & it died. It took it apart & it stayed dead. There is voltage on the connector and on the board. No poking, prodding, twisting brings it back. That pretty much clinches it for me: the board is bad. It is curious how intermittent it was without reacting to anything I did. The saw is under warranty - if I can find the receipt for it (unlikely)! Bob |
#7
Posted to sci.electronics.repair
|
|||
|
|||
Baffled by cordless tool problem
On Monday, December 28, 2015 at 10:49:03 PM UTC-5, Bob Engelhardt wrote:
On 12/28/2015 10:13 PM, Bob Engelhardt wrote: On 12/28/2015 8:22 PM, amdx wrote: On 12/28/2015 6:30 PM, Bob Engelhardt wrote: On 12/28/2015 7:13 PM, wrote: One bad winding on the motor, a bad spot on the commutator, really worn brushes? (Assuming it's not brushless.) ... When it's dead, even the LED does not come on. Which it normally does even without the trigger being pulled. So it can't be commutator, etc. Intermittent battery connection. Mikek I want to say that I've checked that - that there is voltage on the connector terminals when it was dead. But I've gone around in so many circles that I can't remember if I was even able to do that. I.e., if it was ever dead after I opened it. I have wiggled and stressed the battery connector without consequence. When it dies again, that will the first thing I check. Thanks, Bob Update: I put it together & it died. It took it apart & it stayed dead. There is voltage on the connector and on the board. No poking, prodding, twisting brings it back. That pretty much clinches it for me: the board is bad. It is curious how intermittent it was without reacting to anything I did. The saw is under warranty - if I can find the receipt for it (unlikely)! Bob If you can't find the receipt, reflow the board (including the chip). I've seen a lot of reflow repairs where flexing or thermal cycling is inconclusive. Make sure you don't miss the crystal/resonator. Thoroughly clean the board afterwards as some unseen residues can wreak havoc with processor ICs.. |
#8
Posted to sci.electronics.repair
|
|||
|
|||
Baffled by cordless tool problem
On 12/29/2015 2:52 AM, Charlie+ wrote:
On Mon, 28 Dec 2015 22:48:42 -0500, Bob Engelhardt wrote as underneath : snip The saw is under warranty - if I can find the receipt for it (unlikely)! You might have baught it with a credit card, the account would give you proof of purchase.. C+ Oh ... good idea! I almost certainly did use a card. Thanks Bob |
#9
Posted to sci.electronics.repair
|
|||
|
|||
Baffled by cordless tool problem
On 12/29/2015 7:46 AM, John-Del wrote:
If you can't find the receipt, reflow the board (including the chip). I've seen a lot of reflow repairs where flexing or thermal cycling is inconclusive. Make sure you don't miss the crystal/resonator. Thoroughly clean the board afterwards as some unseen residues can wreak havoc with processor ICs. Thanks. I'll definitely try that if I can't get it fixed under warranty. Bob |
#10
Posted to sci.electronics.repair
|
|||
|
|||
Baffled by cordless tool problem
On Monday, December 28, 2015 at 4:17:44 PM UTC-6, Bob Engelhardt wrote:
I have a Milwaukee 12v cordless jig saw. It was working fine then stopped, dead. Then started again, with no symptoms. It did this back & forth a few times, then stayed dead. It never stopped while being used - it just wouldn't start at all. I took it apart to diagnose & as soon as I put it on the battery, it was OK! I reassembled it and periodically tested it over a week. Always OK. Today I put the base/shoe back on & it was dead! As I took it apart again, I kept checking it, but it didn't come back. And then, sitting there, it did come back, spontaneously. It has a small PCB for speed control. The PCB also controls an LED "work light", which comes on when the battery is connected. Except when it's dead - making the LED a good go, no-go indicator. And showing that the problem is more basic than speed-control circuitry. The PCB has a number of wires soldered in through holes. I have checked all of them. I have stressed the board with mild twisting; I've cleaned it with carbon tet; and have warmed it with a hair dryer. Nothing had any effect. The board is SMT (with a 48 pin chip!), except for the wires, 1 cap, and the output FETs, which are TH. Is there anything else that I can try? Thanks, Bob Might this be a battery issue? You see, a lot of these modern battery packs have a Battery Management System circuit board inside the battery pack, and its job is to properly charge the batteries and shut off the battery when it's drained. If the battery pack and the saw have to communicate with each other, maybe the BMS says it's time to shut off the battery, yet the battery is not yet dead. You might be able to check by swapping in a different battery pack. Good luck and Happy New Year. |
#11
Posted to sci.electronics.repair
|
|||
|
|||
Baffled by cordless tool problem
On 1/1/2016 12:17 PM, gyro_john wrote:
Might this be a battery issue? ... You might be able to check by swapping in a different battery pack. I have tried different batteries - it is not a battery problem. Thanks anyhow. |
#12
Posted to sci.electronics.repair
|
|||
|
|||
Baffled by cordless tool problem
On 12/29/2015 3:19 PM, Bob Engelhardt wrote:
On 12/29/2015 7:46 AM, John-Del wrote: If you can't find the receipt, reflow the board (including the chip). ... Thanks. I'll definitely try that if I can't get it fixed under warranty. Bob Long story short: warranty does not apply & I'm going to try to reflow the board. On cleaning the board I found some stuff that looked like the rubbery caulk/adhesive that is used to stabilize components. On removing it I found a TH device that has me puzzled. I'm worried that it might not handle the reflow heat. The pictures show it next to a brass (?!) heatsink that the power FETs sit on and a close-up of it. The rubbery stuff covered it and bonded(?) it to the heatsink. Thermal stuff? https://www.dropbox.com/s/nf2odbubz0...Board.jpg?dl=0 https://www.dropbox.com/s/axu84cbjlp...evice.jpg?dl=0 What is it? Do I need to remove it for reflow? Thanks, Bob |
#13
Posted to sci.electronics.repair
|
|||
|
|||
Baffled by cordless tool problem
On 1/2/2016 12:44 PM, Bob Engelhardt wrote:
.... https://www.dropbox.com/s/nf2odbubz0...Board.jpg?dl=0 https://www.dropbox.com/s/axu84cbjlp...evice.jpg?dl=0 What is it? Do I need to remove it for reflow? I think that it's a thermistor. It _looks_ exactly like this one: http://www.dxmht.com/products/thermal-resistor.htm Since it's soldered in, it should be OK for reflow. Bob |
#14
Posted to sci.electronics.repair
|
|||
|
|||
Baffled by cordless tool problem
On Saturday, January 2, 2016 at 10:24:05 PM UTC-5, Bob Engelhardt wrote:
On 1/2/2016 12:44 PM, Bob Engelhardt wrote: ... https://www.dropbox.com/s/nf2odbubz0...Board.jpg?dl=0 https://www.dropbox.com/s/axu84cbjlp...evice.jpg?dl=0 What is it? Do I need to remove it for reflow? I think that it's a thermistor. It _looks_ exactly like this one: http://www.dxmht.com/products/thermal-resistor.htm Since it's soldered in, it should be OK for reflow. Bob Huh.. learn something new every day. Never saw a thermal resistor in that package, but it sure looks like the one in the link. It seems the board has a conformal coating on it. When resoldering a board like this, it's much easier to accomplish with the coating off. |
Reply |
Thread Tools | Search this Thread |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Forum | |||
OT - frustrated and baffled over garage door springs | Metalworking | |||
Suggestion for cordless tool makers | Home Repair | |||
Baffled by Ballvalve | UK diy | |||
FS Milwaukee Cordless Tool Kit | Woodworking | |||
Has anyone repaired cordless tool batteries | Home Repair |