Home |
Search |
Today's Posts |
|
Woodworking (rec.woodworking) Discussion forum covering all aspects of working with wood. All levels of expertise are encouraged to particiapte. |
Reply |
|
LinkBack | Thread Tools | Display Modes |
#1
Posted to rec.woodworking
|
|||
|
|||
You guys were right, I was wrong
I gave QEP ( tile saw) the benefit of the doubt, but I was a little disappointed, again.
I contacted/complained to QEP and they repeatedly tried to blamed the damage(?) on shipping and handling, but they did offer to replace the saw. I contacted Zoro, whom I bought the saw from, and they didn't hesitate to replace or refund. I elected a refund. I was at Home Depot and noticed they had a model 61024 set up. There was no spacing between that motor housing and blade/blade guard, as my saw had. When I got home, I did another inspection of my saw. Take a look at what else I discovered: the arbor, arbor bearing. I didn't pull/push on it, but the arbor is probably loose, also. No doubt water got inside the motor, also. My initial complaint was about the spacing between the motor and blade guard, hence the exposed arbor would fling/spray water, causing water to get into the switch box area. https://www.flickr.com/photos/43836144@N04/?details=1 I sent QEP and Zoro these pics, with comments. I went by Harbor Freight and checked out their Chicago Electric 10" tile saw. It's heavier than the QEP saw, it looks and feels better built, the stand is more firm/sturdy/larger wheels, the work table slides better, the fence is much, much better, has more HP, less expensive. The only downside: I won't get 20% off (coupon) until Thursday. Sonny |
#2
Posted to rec.woodworking
|
|||
|
|||
You guys were right, I was wrong
"Sonny" wrote: I gave QEP ( tile saw) the benefit of the doubt, but I was a little disappointed, again. snip ---------------------------------------------------------- Glad to see you got out from under that piece of crap. Lew |
#3
Posted to rec.woodworking
|
|||
|
|||
You guys were right, I was wrong
I have used the Chicago Electric, and have not had any issues.
Yes, I cut plenty of paver stones....... Hundreds....... Did 3 tile jobs..........and it has paid for itself..... I had to glue down the rubber mat on the sliding table with contact cement.... The China glue down did not stand up well. The motor is plastic housing, and like many now a days.....it worked fine. The blade cover is cheap plastic too. If it ever fails, I will make one out of sheet metal. It hasnt.... Good Luck. john "Sonny" wrote in message ... I gave QEP ( tile saw) the benefit of the doubt, but I was a little disappointed, again. I contacted/complained to QEP and they repeatedly tried to blamed the damage(?) on shipping and handling, but they did offer to replace the saw. I contacted Zoro, whom I bought the saw from, and they didn't hesitate to replace or refund. I elected a refund. I was at Home Depot and noticed they had a model 61024 set up. There was no spacing between that motor housing and blade/blade guard, as my saw had. When I got home, I did another inspection of my saw. Take a look at what else I discovered: the arbor, arbor bearing. I didn't pull/push on it, but the arbor is probably loose, also. No doubt water got inside the motor, also. My initial complaint was about the spacing between the motor and blade guard, hence the exposed arbor would fling/spray water, causing water to get into the switch box area. https://www.flickr.com/photos/43836144@N04/?details=1 I sent QEP and Zoro these pics, with comments. I went by Harbor Freight and checked out their Chicago Electric 10" tile saw. It's heavier than the QEP saw, it looks and feels better built, the stand is more firm/sturdy/larger wheels, the work table slides better, the fence is much, much better, has more HP, less expensive. The only downside: I won't get 20% off (coupon) until Thursday. Sonny |
#4
Posted to rec.woodworking
|
|||
|
|||
You guys were right, I was wrong
A couple of the tile/masonry guys here in town I use have these saws:
http://www.harborfreight.com/25-hors...saw-69275.html They love 'em. They take a pretty good licking on the jobs, then ride around in the truck at the end of the day. One of them has had his personal saw for about three years! He likes them as they are cheap enough to buy for his guys to have one when they need it, and weigh in at about 1/3 the price he was paying for his normal saws. He rated the saw as "pretty good", and the blade as OK. For large tiles, the blade fine, but for smaller ceramics he had chip out on the cuts. So he moved the stock blade to another saw to cut bricks, pavers, rock, and big clay tiles and solved the problem. He put a better blade on his personal saw and hasn't looked back since. He is a production guy, and it should be noted that if a grout joint, a caulked corner or a piece of trim will hide the minor chipping on the cuts, he lets his guys use the stock blade. I have watched him use this saw on a few jobs, and it whizzes right through big tiles, even with the stock blade. This could be one of those tools that HF got "right". Robert |
#5
Posted to rec.woodworking
|
|||
|
|||
You guys were right, I was wrong
On Tue, 7 Oct 2014 13:19:45 -0700 (PDT), Sonny wrote:
snip The only downside: I won't get 20% off (coupon) until Thursday. 20% off coupons are ALWAYS available he http://www.harborfreight.com/20off-c...aff-17547.html 25% off valid through 12/5/2014: https://slickdeals.net/forums/attach...6&d=1407789919 |
#6
Posted to rec.woodworking
|
|||
|
|||
You guys were right, I was wrong
On Tuesday, October 7, 2014 11:41:32 PM UTC-5, wrote:
A couple of the tile/masonry guys here in town I use have these saws: http://www.harborfreight.com/25-hors...saw-69275.html This could be one of those tools that HF got "right". Yep, that's the saw I compared, checked out. In the store, I muscled it, a bit. It felt more robust than the QEP saw, which felt kind of flimsy. The HF saw, with stand, weighs 10 lbs more than the QEP saw. |
Reply |
Thread Tools | Search this Thread |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Forum | |||
Hey, guys. | Metalworking | |||
I think Bush was wrong and Obama is three times as wrong as Bush was. | Metalworking | |||
O/T: One for the Old Guys | Woodworking | |||
Hi Guys | Electronics Repair | |||
hey guys | Home Repair |