I purchased a jet 1442 earlier this year. While turning some knobs I
discovered that the headstock casting kind of gets in the way if bringing
the 12" stock tool rest up really close. This geometery is only a problem
for narrow & short turning between centers.

So I decided to pick up short tool rest. I ordered the post and a 4" bar
from Lee Valley

http://www.leevalley.com/wood/page.a...330,49238&ap=1

Upon installation, I found that the post is a bit too long. It contacts the
banjo's locking bar mechanism before the bar gets below the axis of the
lathe. A shorter post is not available.

Should I:

1. Send is back and buy an entirely different product? If so What is a
better choice?
2. load up a metal-cutting blade in the recipricating saw and lop it off
3. Other?

Thanks,

Steve

Steve,
Take option #2. Cut it to length. You are likely going to run into the
same thing everywhere. If you don't want to do that, buy a 24" swing
lathe. It'll probably fit perfect on that one....
David


Stephen M wrote:

I purchased a jet 1442 earlier this year. While turning some knobs I
discovered that the headstock casting kind of gets in the way if bringing
the 12" stock tool rest up really close. This geometery is only a problem
for narrow & short turning between centers.

So I decided to pick up short tool rest. I ordered the post and a 4" bar
from Lee Valley

http://www.leevalley.com/wood/page.a...330,49238&ap=1

Upon installation, I found that the post is a bit too long. It contacts the
banjo's locking bar mechanism before the bar gets below the axis of the
lathe. A shorter post is not available.

Should I:

1. Send is back and buy an entirely different product? If so What is a
better choice?
2. load up a metal-cutting blade in the recipricating saw and lop it off
3. Other?

Thanks,

Steve

On Fri, 15 Apr 2005 08:29:18 -0400, "Stephen M"
wrote:

I purchased a jet 1442 earlier this year. While turning some knobs I
discovered that the headstock casting kind of gets in the way if bringing
the 12" stock tool rest up really close. This geometery is only a problem
for narrow & short turning between centers.

So I decided to pick up short tool rest. I ordered the post and a 4" bar
from Lee Valley

http://www.leevalley.com/wood/page.a...330,49238&ap=1

Upon installation, I found that the post is a bit too long. It contacts the
banjo's locking bar mechanism before the bar gets below the axis of the
lathe. A shorter post is not available.

Should I:

1. Send is back and buy an entirely different product? If so What is a
better choice?
2. load up a metal-cutting blade in the recipricating saw and lop it off
3. Other?

Thanks,

Steve

I'd take choice #2, except using a grinder if it isn't a LOT of extra stock to
remove..

Which ever choice you make, I think that (assuming that LV said that it was for
a 1442), you should let LV know, so that they can warn other 1442 owners before
they buy one..



mac

Please remove splinters before emailing

I'd take choice #2, except using a grinder if it isn't a LOT of extra
stock to
remove..

It's about an inch and I don't have a grinder.... that seems like alot to
grind off anyway.


Which ever choice you make, I think that (assuming that LV said that it
was for
a 1442), you should let LV know, so that they can warn other 1442 owners
before
they buy one..

No, it's all my fault. Part of posting here is in that same spirit of
letting other folks know to check post length before purchasing an
aftermarket tool rest. After the fact I did check LV to see if the posts
were offered in different lengths, but that is not the case.

-s

A 4" angle grinder would cut it off easily.

Upon installation, I found that the post is a bit too long. It contacts the
banjo's locking bar mechanism before the bar gets below the axis of the
lathe. A shorter post is not available.

Should I:

1. Send is back and buy an entirely different product? If so What is a
better choice?
2. load up a metal-cutting blade in the recipricating saw and lop it off
3. Other?

Thanks,

Steve

I had a similar problem, but didn't have any means of cutting it to
length, so I took it to a machine shop, and they ran it through their
bandsaw. I think that they only charged me a buck or two.

--
Dan Kozar



remove NOSPAM

"Derek Hartzell" wrote: A 4" angle grinder would cut it off easily.
^^^^^^^^^^^^^^
Or a hack saw. If it's cast iron, you'll be done in 10 min. If it's steel,
a little longer.

one of these could work for you.


http://www.packardwoodworks.com/Merc...GY&Category_Co
de=lathes-acc-toolrst-d4-ct

http://www.packardwoodworks.com/Merc...GY&Category_Co
de=lathes-acc-toolrst-mtrs

neill wrote:
one of these could work for you.


http://www.packardwoodworks.com/Merc...GY&Category_Co
de=lathes-acc-toolrst-d4-ct

http://www.packardwoodworks.com/Merc...GY&Category_Co
de=lathes-acc-toolrst-mtrs


They should fit the ticket for the King Midi lathe as well. I will
probably order one.

They _do_ give you a commission -- right?


--
Will
Occasional Techno-geek
http://woodwork.pmccl.com

On Fri, 15 Apr 2005 15:26:37 -0700, WillR wrote
(in message ):

neill wrote:
one of these could work for you.


http://www.packardwoodworks.com/Merc...=CTGY&Category
_Co
de=lathes-acc-toolrst-d4-ct

http://www.packardwoodworks.com/Merc...=CTGY&Category
_Co
de=lathes-acc-toolrst-mtrs


They should fit the ticket for the King Midi lathe as well. I will
probably order one.

They _do_ give you a commission -- right?




yea, sure, you bet they do. just be sure to give them my name when you place
the order so they'll know where to send the check

neill wrote:
On Fri, 15 Apr 2005 15:26:37 -0700, WillR wrote
(in message ):


neill wrote:

one of these could work for you.


http://www.packardwoodworks.com/Merc...=CTGY&Category
_Co
de=lathes-acc-toolrst-d4-ct

http://www.packardwoodworks.com/Merc...=CTGY&Category
_Co
de=lathes-acc-toolrst-mtrs


They should fit the ticket for the King Midi lathe as well. I will
probably order one.

They _do_ give you a commission -- right?





yea, sure, you bet they do. just be sure to give them my name when you place
the order so they'll know where to send the check



With pleasure. :-)

They do look good and for a reasonable price.


--
Will
Occasional Techno-geek

Thanks for the responses.

One of the responses that I thought I might get was "RS rests stink you
don't want them anyway"

Since I did not get one of those responses, I got out the recipricating saw
with a metal blade. It took about a minute to go through the 1" of steel.

I tidied it up a bit on the benchtop belt sander.

Cheers,

Steve