Home |
Search |
Today's Posts |
|
Metalworking (rec.crafts.metalworking) Discuss various aspects of working with metal, such as machining, welding, metal joining, screwing, casting, hardening/tempering, blacksmithing/forging, spinning and hammer work, sheet metal work. |
Reply |
|
LinkBack | Thread Tools | Display Modes |
#1
Posted to rec.crafts.metalworking
|
|||
|
|||
Adhesion issue - OPTX20/20 readers to safety glasses
I like to wear wrap around safety glasses similar to the ones he
http://www.safetyglassesusa.com/bf50.html I buy this style with the reader lens. For a lot of my work, I would like to have a much larger reader segment, so that I do not have to crane my neck as much or have to lift the glasses up with one hand to be able to see; and just have a much smaller standard vision area to look out of. I have not found off the shelf safety glasses like this. Someone on this board (several years ago) discussed the stick on readers from OPTX20/20. http://optx2020.com/p-2-hydrotac-sti...ng-lenses.aspx I figured using these would give me 50 to 60% of the lower portion of the lens being reader with the balance for looking at further distances. I bought my regular reading diopter and a second set at the next highest diopter for when my head is jammed in too close to focus with my regular reading Rx. I read the instructions before ordering and it appears that one applies a drop of water to the inside of the safety glasses and then wrings the water out to get adhesion. I can not get the reader lens to adhere no matter how hard or mildly I try to wring the water out. And yes, I did wash the glasses with soap prior to trying to apply these to remove any oils that may have been on the lens. And I had the correct orientation of the lens. Anyone else had success in using these? I watched the video on the web page but I did not get any more information than just reading the instructions. |
#3
Posted to rec.crafts.metalworking
|
|||
|
|||
Adhesion issue - OPTX20/20 readers to safety glasses
wrote in message ... I like to wear wrap around safety glasses similar to the ones he http://www.safetyglassesusa.com/bf50.html I buy this style with the reader lens. For a lot of my work, I would like to have a much larger reader segment, so that I do not have to crane my neck as much or have to lift the glasses up with one hand to be able to see; and just have a much smaller standard vision area to look out of. I have not found off the shelf safety glasses like this. Someone on this board (several years ago) discussed the stick on readers from OPTX20/20. http://optx2020.com/p-2-hydrotac-sti...ng-lenses.aspx I figured using these would give me 50 to 60% of the lower portion of the lens being reader with the balance for looking at further distances. I bought my regular reading diopter and a second set at the next highest diopter for when my head is jammed in too close to focus with my regular reading Rx. I read the instructions before ordering and it appears that one applies a drop of water to the inside of the safety glasses and then wrings the water out to get adhesion. I can not get the reader lens to adhere no matter how hard or mildly I try to wring the water out. And yes, I did wash the glasses with soap prior to trying to apply these to remove any oils that may have been on the lens. And I had the correct orientation of the lens. Anyone else had success in using these? I watched the video on the web page but I did not get any more information than just reading the instructions. Prescription eyeglass lenses are polished, but the wrap-around lenses are molded and they may have some residue mold release compound that is very hard to remove. I would not use solvent. Try just a lot of detergent and rubbing with your (clean) finger to remove it. |
Reply |
Thread Tools | Search this Thread |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Forum | |||
Reading Safety Glasses | Woodworking | |||
Free Safety Glasses | UK diy | |||
safety glasses/bifocals | Metalworking | |||
safety glasses | Home Repair | |||
Anti foq safety glasses | UK diy |