Home |
Search |
Today's Posts |
|
Metalworking (rec.crafts.metalworking) Discuss various aspects of working with metal, such as machining, welding, metal joining, screwing, casting, hardening/tempering, blacksmithing/forging, spinning and hammer work, sheet metal work. |
Reply |
|
LinkBack | Thread Tools | Display Modes |
#1
Posted to rec.crafts.metalworking
|
|||
|
|||
One for the Bearing Guru's
Anyone know whether a 35 or 36mm ID bearing can be purchased off the shelf
from someone with an OD less than 46.5MM? I'm guessing it has to be a roller bearing or needle bearing if it exists, but I honestly don't know where to start for such a large one as all my bearing usage is smaller than that... I'd love one with an inner and outer race rather than a needle bearing because the needle bearings take out the shaft they run on when they disintegrate... But I'll settle for any answer that can be found right now. Thanks for any help that can be offered! Regards, Joe Agro, Jr. (800) 871-5022 01.908.542.0244 Automatic / Pneumatic Drills: http://www.AutoDrill.com Multiple Spindle Drills: http://www.Multi-Drill.com Flagship Site: http://www.Drill-N-Tap.com VIDEOS: http://www.youtube.com/user/autodrill V8013-R |
#2
Posted to rec.crafts.metalworking
|
|||
|
|||
One for the Bearing Guru's
On Thu, 11 Jun 2009 11:24:14 -0400, Joe AutoDrill wrote:
Anyone know whether a 35 or 36mm ID bearing can be purchased off the shelf from someone with an OD less than 46.5MM? I'm guessing it has to be a roller bearing or needle bearing if it exists, but I honestly don't know where to start for such a large one as all my bearing usage is smaller than that... I'd love one with an inner and outer race rather than a needle bearing because the needle bearings take out the shaft they run on when they disintegrate... But I'll settle for any answer that can be found right now. Thanks for any help that can be offered! Personally, I don't know anyone with an OD less than 46.5mm. There are such critters, but I'm not sure about "off the shelf", nor about price. The ones I see go by are at one of my clients that does aerospace work; from them I know that you can basically get any ID/OD difference you want in a ball bearing, in ever-thinner rings. But the special ones _aren't_ off the shelf, the prices make me gasp, and I don't know the manufacturers. Do you want me to collect supplier's names when I go in there this afternoon? -- www.wescottdesign.com |
#3
Posted to rec.crafts.metalworking
|
|||
|
|||
One for the Bearing Guru's
"Tim Wescott" wrote in message
... CLIP Do you want me to collect supplier's names when I go in there this afternoon? Can't hurt I suppose. Maybe I'll find an answer with them or maybe I'll practice my gasping technique with you. Thank you! -- Regards, Joe Agro, Jr. (800) 871-5022 01.908.542.0244 Automatic / Pneumatic Drills: http://www.AutoDrill.com Multiple Spindle Drills: http://www.Multi-Drill.com Flagship Site: http://www.Drill-N-Tap.com VIDEOS: http://www.youtube.com/user/autodrill V8013-R |
#4
Posted to rec.crafts.metalworking
|
|||
|
|||
One for the Bearing Guru's
In article ,
"Joe AutoDrill" wrote: Anyone know whether a 35 or 36mm ID bearing can be purchased off the shelf from someone with an OD less than 46.5MM? As I mentioned on one of your pervious bearing quests - plain bearings (bushings, or sleeve bearings if you prefer) do great with small size and high load - even better with pressure lubrication, if available. -- Cats, coffee, chocolate...vices to live by |
#5
Posted to rec.crafts.metalworking
|
|||
|
|||
One for the Bearing Guru's
On Jun 11, 4:24*pm, "Joe AutoDrill" wrote:
Anyone know whether a 35 or 36mm ID bearing can be purchased off the shelf from someone with an OD less than 46.5MM? I'm guessing it has to be a roller bearing or needle bearing if it exists, but I honestly don't know where to start for such a large one as all my bearing usage is smaller than that... I'd love one with an inner and outer race rather than a needle bearing because the needle bearings take out the shaft they run on when they disintegrate... *But I'll settle for any answer that can be found right now. Thanks for any help that can be offered! Needle bearings 35 mm id 42mm od MSC catalog. Probably a little cheaper at a regular bearing house. Dan |
#6
Posted to rec.crafts.metalworking
|
|||
|
|||
One for the Bearing Guru's
"Joe AutoDrill" wrote in message ... Anyone know whether a 35 or 36mm ID bearing can be purchased off the shelf from someone with an OD less than 46.5MM? I'm guessing it has to be a roller bearing or needle bearing if it exists, but I honestly don't know where to start for such a large one as all my bearing usage is smaller than that... I'd love one with an inner and outer race rather than a needle bearing because the needle bearings take out the shaft they run on when they disintegrate... But I'll settle for any answer that can be found right now. Thanks for any help that can be offered! Regards, Joe Agro, Jr. (800) 871-5022 01.908.542.0244 Automatic / Pneumatic Drills: http://www.AutoDrill.com Multiple Spindle Drills: http://www.Multi-Drill.com Flagship Site: http://www.Drill-N-Tap.com VIDEOS: http://www.youtube.com/user/autodrill V8013-R go to www.timkin.com and you can look at their catalog. |
#7
Posted to rec.crafts.metalworking
|
|||
|
|||
One for the Bearing Guru's
On Thu, 11 Jun 2009 11:24:14 -0400, Joe AutoDrill wrote:
Anyone know whether a 35 or 36mm ID bearing can be purchased off the shelf from someone with an OD less than 46.5MM? I'm guessing it has to be a roller bearing or needle bearing if it exists, but I honestly don't know where to start for such a large one as all my bearing usage is smaller than that... I'd love one with an inner and outer race rather than a needle bearing because the needle bearings take out the shaft they run on when they disintegrate... But I'll settle for any answer that can be found right now. Thanks for any help that can be offered! Regards, Joe Agro, Jr. (800) 871-5022 01.908.542.0244 Automatic / Pneumatic Drills: http://www.AutoDrill.com Multiple Spindle Drills: http://www.Multi-Drill.com Flagship Site: http://www.Drill-N-Tap.com VIDEOS: http://www.youtube.com/user/autodrill V8013-R You are looking for a "thin section bearing", and if you do a web search you'll get a lot of hits. I had a mechanical engineer assure me this afternoon that _all_ thin section bearings are aerospace and muy expensivo, but then I got to thinking about his definition (OD to ID ratio less than 2:1) and the dimensions of all the spindle and rear axle bearings I've replaced in various cars, and I decided that in addition to being in his early 20's, he's young. For aerospace-oriented bearings, look to New Hampshire Ball Bearing company and Kayeon. Boca bearings sells all sorts of bearings to non- technical users (they started out strictly selling bearings to folks rebuilding model airplane engines); they don't appear to have what you want on their web site but it may be worth your while to give them a call. Let us know how it works out! I'm curious. -- www.wescottdesign.com |
#8
Posted to rec.crafts.metalworking
|
|||
|
|||
One for the Bearing Guru's
Joe AutoDrill wrote:
Anyone know whether a 35 or 36mm ID bearing can be purchased off the shelf from someone with an OD less than 46.5MM? I'm guessing it has to be a roller bearing or needle bearing if it exists, but I honestly don't know where to start for such a large one as all my bearing usage is smaller than that... I'd love one with an inner and outer race rather than a needle bearing because the needle bearings take out the shaft they run on when they disintegrate... But I'll settle for any answer that can be found right now. They are called "thin section" bearings, and a number of makers have separate catalogs of these. They are made just like standard ball bearings but with thinner races and smaller balls than you would see in general use. Thus the ratio of inner to outer radius can be a lot closer. I think any bearing distributor should have these catalogs. Jon |
#9
Posted to rec.crafts.metalworking
|
|||
|
|||
One for the Bearing Guru's
Calif Bill wrote:
go to www.timkin.com and you can look at their catalog. Who the hell is timkin? I think you meant TimkEn..... Jon |
#10
Posted to rec.crafts.metalworking
|
|||
|
|||
One for the Bearing Guru's
"Jon Elson" wrote in message ... Calif Bill wrote: go to www.timkin.com and you can look at their catalog. Who the hell is timkin? I think you meant TimkEn..... Jon Yup a mis spelling. Got your jollies for the day. |
#11
Posted to rec.crafts.metalworking
|
|||
|
|||
One for the Bearing Guru's
On Jun 14, 12:28*am, Jon Elson wrote:
Joe AutoDrill wrote: Anyone know whether a 35 or 36mm ID bearing can be purchased off the shelf from someone with an OD less than 46.5MM? http://www.skf.com/portal/skf/home/p...=first&lang=en |
#12
Posted to rec.crafts.metalworking
|
|||
|
|||
One for the Bearing Guru's
"Ecnerwal" wrote in message
... Anyone know whether a 35 or 36mm ID bearing can be purchased off the shelf from someone with an OD less than 46.5MM? As I mentioned on one of your pervious bearing quests - plain bearings (bushings, or sleeve bearings if you prefer) do great with small size and high load - even better with pressure lubrication, if available. Unfortunately, I have to slide the bearing over an obstruction that is around 35mm and then inside a space constraint around 47mm or greater... Thus the specific needs in this case. -- Regards, Joe Agro, Jr. (800) 871-5022 01.908.542.0244 Automatic / Pneumatic Drills: http://www.AutoDrill.com Multiple Spindle Drills: http://www.Multi-Drill.com Flagship Site: http://www.Drill-N-Tap.com VIDEOS: http://www.youtube.com/user/autodrill V8013-R |
#13
Posted to rec.crafts.metalworking
|
|||
|
|||
One for the Bearing Guru's
Let us know how it works out! I'm curious.
I haven't checked out the thin section bearing offerings just yet... But I did check out the needle bearing choice given me... Although it's workable, I'm seriously worried that the bearing itself is going to ruin a 500 shaft... And since I have 24 of these shafts to support... You can get the picture. Thus my deisre for a bearing with inner and outer race. I'll let you know if I get a good look at the thin section bearings anytime soon for sure! Thank you and all the others for the ideas. -- Regards, Joe Agro, Jr. (800) 871-5022 01.908.542.0244 Automatic / Pneumatic Drills: http://www.AutoDrill.com Multiple Spindle Drills: http://www.Multi-Drill.com Flagship Site: http://www.Drill-N-Tap.com VIDEOS: http://www.youtube.com/user/autodrill V8013-R |
Reply |
Thread Tools | Search this Thread |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Forum | |||
Machine a bearing?? - Ford Major Diesel 2 stage clutch bearing | Metalworking | |||
Any water pump guru's here?? | Home Repair | |||
Analog guru's? Controling adjustable regulator with DAC output? | Electronic Schematics | |||
Electrical guru's? | UK diy | |||
Any Solid Surface Guru's out there? | Woodworking |