I currently have a Sears compressor and paint pot sprayers.

I was wondering how the HVLP systems compare. My main questions a do
they have the overspray of the paint pots, and do they require a different
compressor.

I am going to be using this to spray ornamental metal. (square tubing
colloquially called wrought iron)

Other comments and observations appreciated.

Thanks in advance.

alt.airbrush.art



SteveB wrote:
I currently have a Sears compressor and paint pot sprayers.

I was wondering how the HVLP systems compare. My main questions a do
they have the overspray of the paint pots, and do they require a different
compressor.

I am going to be using this to spray ornamental metal. (square tubing
colloquially called wrought iron)

Other comments and observations appreciated.

Thanks in advance.

SteveB wrote:
I currently have a Sears compressor and paint pot sprayers.

I was wondering how the HVLP systems compare. My main questions a do
they have the overspray of the paint pots,

No, not near as much, but still some will get onto unprotected surfaces.

and do they require a different
compressor.

You have to take that High Volume part seriously. My Sears Buzzbomb is
rated about 7 CFM at 90 psi IIRC, and it cannot keep up. That has only
been an issue when painting a car


I am going to be using this to spray ornamental metal. (square tubing
colloquially called wrought iron)

Should be ideal for that. I've been using a $50 HF unit for a couple of
years. Recently Sharpe came out with their Finex line. That looks to be
the best gun for the money.

Rex B

SteveB wrote:
I currently have a Sears compressor and paint pot sprayers.

I was wondering how the HVLP systems compare. My main questions a do
they have the overspray of the paint pots, and do they require a different
compressor.

I am going to be using this to spray ornamental metal. (square tubing
colloquially called wrought iron)

Other comments and observations appreciated.

Thanks in advance.

I assume you're looking at one of the "HVLP" guns that you hook up to a
regular air compressor. If you were looking at a real HVLP outfit like
they use for applying wood finishes, you wouldn't be asking about a
compressor. Those use a turbine drive, something like a big vacuum
cleaner turbine with hoses about the same size as a home vacuum.
They're too rich for my bank account, but they do deliver the goods.
I've played with them at the woodworking shows, there's not much
overspray at all, can be controlled almost like an airbrush. They
seemed to handle fairly heavy materials like latex and urethane
varnishes.

What I have is one of the HF cheapy conversion-type guns, a 4 cfm
compressor can keep up for small areas, say about 8 oz. of thinned
material applied. Not quite as much overspray and bounce-back as a
regular paint gun but more than a real HVLP unit would have. The
pattern can be adjusted easily, so you should be able to do your tubing
just fine. You'll still need some sort of spray booth, makeshift or
not, plus a respirator. I like the top-feed ones, you'll need the
stand that goes with it(and that they sell separately). I've used mine
enough that the plastic cup cracked and broke, I replaced it with an
aluminum jobbie, a much better deal, the cap doesn't leak. Mine has
been used for shellac on wood and for doing automotive touch-up with
two-part urethane and clearcoat. I did do the roof of my van with it,
it was a stretch, though, for the compressor. The one I have uses
generic internal strainers that I can get from the body supply shop
relatively cheaply, which surprised me. I think the top-feed units are
easier to clean than siphon units, too, just my opinion.

If you're doing it for money, go for the real HVLP outfit(not my money
after all!!).

Stan