This is a Kenmore Direct Drive Washer...

Worked fine until one morning I put a load in, turned it on, and it
started fine.

Later that morning, my wife went to put the load in the dryer and it
was still full of water. The cycle was done though.

After manually draining the tub, I tried to run it through another
cycle. It fills the tub and the knob goes through the whole cycle, but
nothing else happens... it doesn't even drain the water at the end of
the cycle. During the cycle, I do hear some humming coming from the
machine (as if the motor was trying to run maybe???).

Along with this, there is a distinct smell of burnt wires or something
burning.

I've opened up the machine and determined that it wasn't the coupler.

What could be the problem/next action to take?

Thanks,
Brian

wrote in message

After manually draining the tub, I tried to run it through another
cycle. It fills the tub and the knob goes through the whole cycle, but
nothing else happens... it doesn't even drain the water at the end of
the cycle. During the cycle, I do hear some humming coming from the
machine (as if the motor was trying to run maybe???).

Along with this, there is a distinct smell of burnt wires or something
burning.

Probably the drain valve not opening to let the water out. You can do some
troubleshooting at:
www.applianceaid.com
www.repairclinic.com

It could be a host of things, but not the "drain valve", it doesn't have
one.
It could be:
The motor
The motor switch
Something caught in the pump
The timer
The transmission
The wiring





wrote

This is a Kenmore Direct Drive Washer...

Worked fine until one morning I put a load in, turned it on, and it
started fine.

Later that morning, my wife went to put the load in the dryer and it
was still full of water. The cycle was done though.

After manually draining the tub, I tried to run it through another
cycle. It fills the tub and the knob goes through the whole cycle, but
nothing else happens... it doesn't even drain the water at the end of
the cycle. During the cycle, I do hear some humming coming from the
machine (as if the motor was trying to run maybe???).

Along with this, there is a distinct smell of burnt wires or something
burning.

I've opened up the machine and determined that it wasn't the coupler.

What could be the problem/next action to take?

Thanks,
Brian

Gosh Ed, that sure was helpful. Next time save yourself the trouble and
just say:

"Sounds like there is something wrong somewhere."

wrote

Along with this, there is a distinct smell of burnt wires or something
burning.

Take the two clips off the pump and hold it out of the way and see if the
machine will agitate.
If it does the problem is with the pump.
If it doesn't, the problem is with the motor, motor switch, or transmission.

"Matt" wrote

Gosh Ed, that sure was helpful. Next time save yourself the trouble and
just say:

"Sounds like there is something wrong somewhere."

Those are the facts.
Are you still upset that you never really learned anything in life. Why
don't you get over it?
Instead of stewing in your ineptness, why not offer a suggestion to the
original poster?

Because Ed, unlike you - I'm willing to admit I don't have the first
clue about what the problem with the washer is.

I suppose I could use your strategy, which is to mention every major
part in the washer, followed by - 'one of these could be the problem' -
but I choose not to.

I thought you said your mamma drowned all the dumb babies, Ed.

"Matt" wrote

Because Ed, unlike you

I'm greatful for that. Now, why don't you go find yourself a nice quiet
place and grow up. I don't feel much like arguing with 12 year olds today. I
don't like to add people to my kill file but when some single cell bacteria
attaches itself to you, you should remove it if you can.

If I did killfile you I wouldn't be missing much.
Here are some of your recent 'useful' statements, each from a different
post:

"Sounds like there is something wrong somewhere."

"I think Sasha is a pretty name."

"Whats his second wish?"

"One time I put down tile before the subfloor went in. Then I had the
housewarming party! Talk about embarrasing!!!! My family still isnt
talking to me. The ones still alive, I mean."

"Oh I dont know. Pop rocks and coke can clear almost anything."

"That is EXACTLY what the professor said to Gilligan, and look how that
turned out."

I could go on but everyone gets the idea.

"You dont have one arm in there when you try to close it, do you? Cause
that will do it every time with a simpson! Doh! Slam! Doh! Slam! Doh! Slam!"

I don't know what this group would do without you.

Aw eddy! I'm so glad you have been following all my posts!

But regardless of what you may think of my posts, and no matter what
you do to change the subject:

The fact is you are a clueless old man who not only cannot repair
appliances, but also can't admit this basic fact.
Instead, you would rather tell other posters they are wrong (you've
done it to Edwin and me now), and then offer nonhelp.

Uh the problem is in the timer, the pump, the wiring, the motor, or the
transmission.

Thanks for the help, Eddie! YOU ARE GOOD!

Well Matt, at least Ed is TRYING to be helpful... you're just stirring
****.

Thanks Ed, I will try taking the pump out of the system to see what
happens.

Brian

wrote in message
ups.com...
This is a Kenmore Direct Drive Washer...

Worked fine until one morning I put a load in, turned it on, and it
started fine.

Later that morning, my wife went to put the load in the dryer and it
was still full of water. The cycle was done though.

After manually draining the tub, I tried to run it through another
cycle. It fills the tub and the knob goes through the whole cycle, but
nothing else happens... it doesn't even drain the water at the end of
the cycle. During the cycle, I do hear some humming coming from the
machine (as if the motor was trying to run maybe???).

Along with this, there is a distinct smell of burnt wires or something
burning.

I've opened up the machine and determined that it wasn't the coupler.

What could be the problem/next action to take?

Thanks,
Brian

How old is it?
It might not have a self-reversing lint filter in the pump out thing. They
make them now so they don't clog but the old ones weren't like that.
Fortunatly the older ones are also not a one piece molded sealed thing. You
should be able to open it up and pull out the clog. Just be aware that some
water is going to POUR OUT OF THE HOSE once you disconnect the pump. So just
krimp it off with some vise grips or something or else you will have that 15
gallons of water on the floor. You might want to just scoop the water out if
it's next to a sink. Those little basins they send you home from the
hospital with will fit nicely under the washer stuff to catch spills. Its
going to be a mess but I tink it's doable especially since you heard the hum
and it did not kick off. At least you said its direct drive so your belt
won't be stretched out from heating up. Good luck.

After careful reflection, I've decided you are right Brian.

Ed, I am sorry for criticising you and your skills.

Brian, the problem is somewhere in the pump, the transmission, the
wiring, the motor, or the timer.

Could be in the frame too; but can't be sure until you post a model #.

HTH.

"Matt" wrote

Ed, I am sorry

That's obvious. One of the sorriest I've run across.

I have a Maytag with the same problem. It happened when I washed the
clothes in the "whites" cycle. I switched to washing clothes in the
"colors" cycle and it works fine. Maybe the problem has to do with the
cycle, like something with the timer. Try washing in a different cycle
like delicates and see if the same thing happens.

Lets see now. Ed has plonked me, but something tells me he MUST HAVE
THE LAST WORD. So lets see.

Hey dickhEaD, how ya doing today?