Home |
Search |
Today's Posts |
|
Home Repair (alt.home.repair) For all homeowners and DIYers with many experienced tradesmen. Solve your toughest home fix-it problems. |
Reply |
|
|
LinkBack | Thread Tools | Display Modes |
|
#1
Posted to alt.home.repair
|
|||
|
|||
Circuit breaker keeps tripping
How do I debug when a circuit breaker keeps tripping?
1. It has never tripped before (years). 2. Yesterday, it was tripped. 3. I flip it back on, and it trips immediately. 4. It controls a bunch of outlets and lights and that's about it. I turn off the lights it controls. I unplug all the outlets. It still trips. How do you debug these things? |
#2
Posted to alt.home.repair
|
|||
|
|||
Circuit breaker keeps tripping
On 01/20/2016 02:04 AM, E. Robinson wrote:
How do I debug when a circuit breaker keeps tripping? 1. It has never tripped before (years). 2. Yesterday, it was tripped. 3. I flip it back on, and it trips immediately. 4. It controls a bunch of outlets and lights and that's about it. I turn off the lights it controls. I unplug all the outlets. It still trips. How do you debug these things? I'd start by disconnecting the load at the breaker and then see if the breaker still trips. If the breaker is OK, then I'd start removing and disconnecting outlets and switches on the affected circuit until I found the problem. You didn't recently nail/screw/install something on a wall, did you? |
#3
Posted to alt.home.repair
|
|||
|
|||
Circuit breaker keeps tripping
On Wed, 20 Jan 2016 04:24:55 -0500, Dick Phallic wrote:
I'd start by disconnecting the load at the breaker and then see if the breaker still trips. If the breaker is OK, then I'd start removing and disconnecting outlets and switches on the affected circuit until I found the problem. You didn't recently nail/screw/install something on a wall, did you? To "disconnect the load at the breaker", do you mean that I should just physically *remove* the breaker, and see if it trips on its own, in my hands? To "disconnect outlets and switches", do you mean to pull them out of the wall, one by one, disconnecting the hot wire only? (Would that be enough?) No, I didn't recently install anything (that I know of). |
#4
Posted to alt.home.repair
|
|||
|
|||
Circuit breaker keeps tripping
On Wed, 20 Jan 2016 10:45:55 -0000 (UTC), "E. Robinson"
wrote: To "disconnect the load at the breaker", do you mean that I should just physically *remove* the breaker, and see if it trips on its own, in my hands? UMM... AHHH, UMMMM, AHHHHH ..... WOW ............ AHHHHH OK.... I think they meant you should remove the LOAD from your telephone book, (such as a stack of other books on top of it), then look up electricians and call one. The only only thing that might trip in your hands, is your index finger, if it trips while your fingers do the walking thru the yellow pages. Yep, that's what they meant! To "disconnect outlets and switches", do you mean to pull them out of the wall, one by one, disconnecting the hot wire only? (Would that be enough?) They just meant you should disconnect (unplug) everything until the electrician arrives. No, I didn't recently install anything (that I know of). That's good! |
#5
Posted to alt.home.repair
|
|||
|
|||
Circuit breaker keeps tripping
On 1/20/2016 4:45 AM, E. Robinson wrote:
On Wed, 20 Jan 2016 04:24:55 -0500, Dick Phallic wrote: I'd start by disconnecting the load at the breaker and then see if the breaker still trips. If the breaker is OK, then I'd start removing and disconnecting outlets and switches on the affected circuit until I found the problem. You didn't recently nail/screw/install something on a wall, did you? To "disconnect the load at the breaker", do you mean that I should just physically *remove* the breaker, and see if it trips on its own, in my hands? To "disconnect outlets and switches", do you mean to pull them out of the wall, one by one, disconnecting the hot wire only? (Would that be enough?) No, I didn't recently install anything (that I know of). In the situation you describe, I suspect that the easiest way to debug is to replace the breaker. I'm told that sometimes they just crap out on their own after years of use. Your time is worth something and the breaker isn't that expensive. Buy a replacement and swap it out and see what happens. |
#6
Posted to alt.home.repair
|
|||
|
|||
Circuit breaker keeps tripping
On Wed, 20 Jan 2016 06:35:36 -0600, Unquestionably Confused
wrote: On 1/20/2016 4:45 AM, E. Robinson wrote: On Wed, 20 Jan 2016 04:24:55 -0500, Dick Phallic wrote: I'd start by disconnecting the load at the breaker and then see if the breaker still trips. If the breaker is OK, then I'd start removing and disconnecting outlets and switches on the affected circuit until I found the problem. You didn't recently nail/screw/install something on a wall, did you? To "disconnect the load at the breaker", do you mean that I should just physically *remove* the breaker, and see if it trips on its own, in my hands? To "disconnect outlets and switches", do you mean to pull them out of the wall, one by one, disconnecting the hot wire only? (Would that be enough?) No, I didn't recently install anything (that I know of). In the situation you describe, I suspect that the easiest way to debug is to replace the breaker. I'm told that sometimes they just crap out I had a GFCI breaker fail when it was only about 5 years old. The replacement is 31 years old and doing fine. Regular breakers are a quite a bit cheaper than GFCI on their own after years of use. Your time is worth something and the breaker isn't that expensive. Buy a replacement and swap it out and see what happens. If he's going to do this he should turn off all the power to the breaker box by flipping the main breaker at the top, and use a flashlight to see. Or at the verrry least he should keep one hand in his pocket, literally, so he can't touch things with two hands and get killed, literally. First turn off the breaker in question. Then when the breaker is off, unscrew the screw that holds the wire at the end of the breaker that's not in the middle of the box. Probably don't have to unscrew it all the way. You don't want the screw dropping into the box, and you don't want to be reflexively showing your hand in the box when you see the screw about to fall. If it does fall, just let it. Grab the wire on that screw by its insulation and push, pull etc. it off the screw. Then lift the end of the breaker away from the center of the box up and pull/rock the breaker out of the clip it's in at the center. It should come out quickly. Reverse to install. Except that it might be easier to hook the wire on the screw BEFORE putting the breaker in at all. Maybe you can use two hands for this part only. You definitely DON"T want to remove the screw, if it even comes out, because it will be hard to get it back in, but it probably comes out enough that it's easy to hook the wire back on it. Use the same size breaker, 15A, 20A, whatever was there. You can't safely increase the size. |
#7
Posted to alt.home.repair
|
|||
|
|||
Circuit breaker keeps tripping
On Wednesday, January 20, 2016 at 8:12:36 AM UTC-5, Micky wrote:
If he's going to do this he should turn off all the power to the breaker box by flipping the main breaker at the top, and use a flashlight to see. Or at the verrry least he should keep one hand in his pocket, literally, so he can't touch things with two hands and get killed, literally. First turn off the breaker in question. Then when the breaker is off, unscrew the screw that holds the wire at the end of the breaker that's not in the middle of the box. Probably don't have to unscrew it all the way. You don't want the screw The OP doesn't know anything about a panel and you've left out an important step that will confuse him. After you've turned off the main breaker, you can't see the screws or the wires. There is a safety shield in place. That must be removed, carefully. And remember, with the main breaker turned off, there is no power to the buss bars, BUT there still is lethal current available up top. |
#8
Posted to alt.home.repair
|
|||
|
|||
Circuit breaker keeps tripping
On Wednesday, January 20, 2016 at 4:24:51 AM UTC-5, Dick Phallic wrote:
On 01/20/2016 02:04 AM, E. Robinson wrote: How do I debug when a circuit breaker keeps tripping? 1. It has never tripped before (years). 2. Yesterday, it was tripped. 3. I flip it back on, and it trips immediately. 4. It controls a bunch of outlets and lights and that's about it. I turn off the lights it controls. I unplug all the outlets. It still trips. How do you debug these things? I'd start by disconnecting the load at the breaker and then see if the breaker still trips. Or switch wires at the breaker between that breaker and an adjacent one as a test. |
#9
Posted to alt.home.repair
|
|||
|
|||
Circuit breaker keeps tripping
On Wed, 20 Jan 2016 04:58:38 -0800, trader_4 wrote:
Or switch wires at the breaker between that breaker and an adjacent one as a test. Nice idea! Thanks! That saves me the 30-mile round trip to the hardware store. (Am in the boonies.) |
#10
Posted to alt.home.repair
|
|||
|
|||
Circuit breaker keeps tripping
On Wednesday, January 20, 2016 at 1:04:57 AM UTC-6, E. Robinson wrote:
How do I debug when a circuit breaker keeps tripping? 1. It has never tripped before (years). 2. Yesterday, it was tripped. 3. I flip it back on, and it trips immediately. 4. It controls a bunch of outlets and lights and that's about it. I turn off the lights it controls. I unplug all the outlets. It still trips. How do you debug these things? Does it actually *reset* and then trip? When they go bad they don't reset or *catch*...showing you its needs replacing. Have any of the outlets been worked-on to be suspect? |
#11
Posted to alt.home.repair
|
|||
|
|||
Circuit breaker keeps tripping
On Wed, 20 Jan 2016 04:44:00 -0800, bob_villain wrote:
Does it actually *reset* and then trip? When they go bad they don't reset or *catch*...showing you its needs replacing. Have any of the outlets been worked-on to be suspect? Haven't anyone in the house to see if the lights go on momentarily, and I can snap a video if you like (will need to find a place to upload it). When I reset it, it doesn't stay. It's as if a spring-like force is forcing it to the trip point. There are three positions, but it won't stay in the off position, and it will easily stay in the trip midway position, but it won't stay in the on position. I tried it a dozen or more times, and all goes right to the trip position. Once I saw a spark, not big, but blue. Stopped at that point. Clearly a short somewhere. |
#12
Posted to alt.home.repair
|
|||
|
|||
Circuit breaker keeps tripping
"E. Robinson" wrote in message ... When I reset it, it doesn't stay. It's as if a spring-like force is forcing it to the trip point. There are three positions, but it won't stay in the off position, and it will easily stay in the trip midway position, but it won't stay in the on position. I tried it a dozen or more times, and all goes right to the trip position. Once I saw a spark, not big, but blue. Stopped at that point. Clearly a short somewhere. If it will not stay in the OFF position that indicates something is wrong with that breaker. A spark or flash does not mean much. If there is a bad overload, repeated resetting of the breaker could cause it to go bad. |
#13
Posted to alt.home.repair
|
|||
|
|||
Circuit breaker keeps tripping
On Wed, 20 Jan 2016 13:16:39 -0500, Ralph Mowery wrote:
If it will not stay in the OFF position that indicates something is wrong with that breaker. A spark or flash does not mean much. If there is a bad overload, repeated resetting of the breaker could cause it to go bad. It stays fine in the off position. Sorry if I wasn't clear. Here it is in the off position (top right, 4th down, 15 amp). http://i65.tinypic.com/i5692c.jpg Here it trips the instant I try to set it to on. http://i66.tinypic.com/2ec2kol.jpg |
#14
Posted to alt.home.repair
|
|||
|
|||
Circuit breaker keeps tripping
On Wed, 20 Jan 2016 18:41:38 -0000 (UTC), "E. Robinson"
wrote: On Wed, 20 Jan 2016 13:16:39 -0500, Ralph Mowery wrote: If it will not stay in the OFF position that indicates something is wrong with that breaker. A spark or flash does not mean much. If there is a bad overload, repeated resetting of the breaker could cause it to go bad. It stays fine in the off position. Sorry if I wasn't clear. Here it is in the off position (top right, 4th down, 15 amp). http://i65.tinypic.com/i5692c.jpg Here it trips the instant I try to set it to on. http://i66.tinypic.com/2ec2kol.jpg Temporarily it has this: Tinypic Site Maintenance Images and videos will continue to serve during this short maintenance. |
#15
Posted to alt.home.repair
|
|||
|
|||
Circuit breaker keeps tripping
"E. Robinson" wrote in message ... How do I debug when a circuit breaker keeps tripping? 1. It has never tripped before (years). 2. Yesterday, it was tripped. 3. I flip it back on, and it trips immediately. 4. It controls a bunch of outlets and lights and that's about it. I turn off the lights it controls. I unplug all the outlets. It still trips. How do you debug these things? Take the wire off the breaker. See if it will reset. If not, get a new breaker. If it resets, take a meter and see how many ohms it shows to the neutral wire for that breaker. Then see how many ohms to ground. If any ohms to ground you have a major problem to look at, should not be any, or way up in the mega ohms atleast. If any below several thousand (really should be up in the megaohms same as to ground) on the neutral to the wire you took off the breaker then something is still connected or there is a short in the wiring. If very high ohms to neutral and ground, then swap that wire with another breaker wire of the same rating and see if the other breaker trips. If not, replace the breaker that is tripping. This is assuming you do not have a ground fault breaker. If so it could be water on an outside outlet that may not show up on the ohm meter. If you had a meter that has a clamp on ampmeter, you could look at it and see if it goes way up when you turn the breaker on, but many do not have a meter like that. If you don't have a multimeter, get one as they are less than $ 20 for one that is good enough to use around the house. |
#16
Posted to alt.home.repair
|
|||
|
|||
Circuit breaker keeps tripping
On Wed, 20 Jan 2016 10:40:53 -0500, Ralph Mowery wrote:
Take the wire off the breaker. See if it will reset. Another great debugging idea. Will try. |
#17
Posted to alt.home.repair
|
|||
|
|||
Circuit breaker keeps tripping
On 1/20/2016 12:04 AM, E. Robinson wrote:
How do I debug when a circuit breaker keeps tripping? 1. It has never tripped before (years). 2. Yesterday, it was tripped. "It /was/ tripped" suggests you discovered it tripped; as opposed to it tripping while you were DOING SOMETHING. 3. I flip it back on, and it trips immediately. Does "immediately" mean "within a few seconds"? Or, does it mean "it never actually SETS"? You are REsetting it before attempting to SET it (i.e., turn it fully OFF, then ON)? 4. It controls a bunch of outlets and lights and that's about it. Are you positive that there are no other hidden loads? Doorbell? AC powered smoke detector? Wall clock? etc. I turn off the lights it controls. I unplug all the outlets. How many lights does it control? How many outlets? Are there other outlets or lights in those rooms that are NOT on the same circuit? It still trips. How do you debug these things? I asume you want to know how *you* should debug this, not I? What level of experience with electricity do you have? And, your personal "Comfort Factor"? How deep is your wallet? I.e., are you asking out of curiosity? Or, out of *need* (ABSOLUTELY can't afford to hire someone)? |
#18
Posted to alt.home.repair
|
|||
|
|||
Circuit breaker keeps tripping
On Wed, 20 Jan 2016 10:36:12 -0700, Don Y wrote:
"It /was/ tripped" suggests you discovered it tripped; as opposed to it tripping while you were DOING SOMETHING. Yep. Woke up in the morning. Some kitchen and adjacent living room lights wouldn't go on. All I can tell at the moment are the lights (three ceiling lights, each with switches). I presume there are some outlets on it too, but I haven't checked yet. Nothing is plugged into any of the nearby outlets. Does "immediately" mean "within a few seconds"? Or, does it mean "it never actually SETS"? You are REsetting it before attempting to SET it (i.e., turn it fully OFF, then ON)? It has three positions. 1. I found it in the trip (middle, sort of) position. 2. It easily stays in the off position. 3. It won't get into the on position - immediate swings to trip. Are you positive that there are no other hidden loads? Doorbell? AC powered smoke detector? Wall clock? etc. Nope. It's a section of the kitchen next to the dining room. I will dig up my outlet tester plug, and check a few of the nearby outlets, but all the lights are ceiling lights and all are currently switched (and the switches are all off). How many lights does it control? How many outlets? Are there other outlets or lights in those rooms that are NOT on the same circuit? At least four built-in lights. All switched. Dunno how many (if any) outlets yet. Will need to test around with a spare desk lamp. Can't find my damn Fluke DMM. WHere did I put that thing? (Haven't used it in a couple of years.) I asume you want to know how *you* should debug this, not I? Yes. I want ideas to debug. I think I have enough to start. 1. Check the outlets for power. 2. Check the breaker in my hands that it switches. 3. Switch the breaker with another breaker. 4. Pull the affected switches and outlets & disconnect black lead (Some are 3-way so I'll be expecting a red lead maybe.) What level of experience with electricity do you have? Same as anyone else I would think. I've wire-nutted replacement outlets a half dozen times. I've replaced a circuit breaker (220V for AC) only once. I put in a 3-way ceiling light once (put a box in the attic and dropped the wires down from between the wall to get to the switch). For tools I have the basic yellow plug 3-light outlet tester. I have a red neon-light probe dumb tester. I can't find my Fluke DMM (but it's overkill usually). And, your personal "Comfort Factor"? How deep is your wallet? I.e., are you asking out of curiosity? Or, out of *need* (ABSOLUTELY can't afford to hire someone)? I can "afford" to waste my money on an electrician, but, I don't really have the money to spare. Plus, I'm only lacking in my debugging skills. Once I know what the problem is, I don't think the "fix" will be difficult. It's figuring out a strategy for finding the problem that I am asking help with - and - I think you boys gave me a pretty good start because I wasn't sure which way to go first since the stuff is all "hidden" in the walls. |
#19
Posted to alt.home.repair
|
|||
|
|||
Circuit breaker keeps tripping
On 1/20/2016 11:23 AM, E. Robinson wrote:
On Wed, 20 Jan 2016 10:36:12 -0700, Don Y wrote: "It /was/ tripped" suggests you discovered it tripped; as opposed to it tripping while you were DOING SOMETHING. Yep. Woke up in the morning. Some kitchen and adjacent living room lights wouldn't go on. All I can tell at the moment are the lights (three ceiling lights, each with switches). Hmmm... I think modern homes tend to keep the kitchen circuits separate from other rooms. Kitchen is the big pig when it comes to electricity usage. I presume there are some outlets on it too, but I haven't checked yet. Nothing is plugged into any of the nearby outlets. Does "immediately" mean "within a few seconds"? Or, does it mean "it never actually SETS"? You are REsetting it before attempting to SET it (i.e., turn it fully OFF, then ON)? It has three positions. 1. I found it in the trip (middle, sort of) position. 2. It easily stays in the off position. 3. It won't get into the on position - immediate swings to trip. I'm not trying to be a stickler but want to make sure of your use of the word "immediately". Does the switch make *any* attempt to stay in the ON position? A short/overload on the circuit will cause the breaker to "trip" *AS* you are trying to turn it on! I.e., it will never really get into the ON position before you feel it going limp under your fingers. If, instead, it tries to catch but trips a second or two later, that's a slightly different story. Are you positive that there are no other hidden loads? Doorbell? AC powered smoke detector? Wall clock? etc. Nope. It's a section of the kitchen next to the dining room. And, it's NOT a GFCI circuit? And, it's a 120V line? Is the breaker a single breaker? Or, a "dual" (though NOT 220V)? I will dig up my outlet tester plug, and check a few of the nearby outlets, but all the lights are ceiling lights and all are currently switched (and the switches are all off). How many lights does it control? How many outlets? Are there other outlets or lights in those rooms that are NOT on the same circuit? At least four built-in lights. All switched. Dunno how many (if any) outlets yet. I'm not really interested in the actual numbers. Rather, just wanting to make sure you've not overlooked an outlet or a switch someplace that *should* be part of the same branch circuit. E.g., we have two switches to control the overhead lights in the kitchen -- both in the same Jbox (one does the lights over the sink, the other does the rest). It would be highly unlikely that encountering a similar setup would have those switches on different circuits. Will need to test around with a spare desk lamp. Can't find my damn Fluke DMM. WHere did I put that thing? (Haven't used it in a couple of years.) I asume you want to know how *you* should debug this, not I? Yes. I want ideas to debug. I think I have enough to start. 1. Check the outlets for power. 2. Check the breaker in my hands that it switches. 3. Switch the breaker with another breaker. 4. Pull the affected switches and outlets & disconnect black lead (Some are 3-way so I'll be expecting a red lead maybe.) With the breaker TRIPPED (i.e., OFF), verify there is NO power at any of the outlets or light fixtures. If there is power, then either you've picked the wrong outlet *or* there may be a short to the other hot leg that is now feeding through (because the breaker on the first hot leg has tripped -- before the breaker on that other hot leg). [This is highly unlikely. But, stresses the fact that you are now operating in an unusual situation so your assumptions always need to be suspect --- especially if your safety is at risk. If the circuit IS off, then it doesn't hurt to verify! : ] *Smell* each outlet/fixture. And look for any signs of burning or melting (metal can melt/"pit" when a short draws an arc to that point). I have a little fixture I made (trivial) that lets me hook my DMM to a NEMA *plug*. So, I can just plug the thing into outlets and check for voltage -- without having to poke probes into the receptacle and *hope* I touch the mating blades inside. For light fixtures, I use a screw-in adapter: http://ak.buy.com/PI/0/500/228885907.jpg into which I plug this other DMM adapter. Again, it makes it easier than trying to poke around with bare probe tips and possibly shorting out the socket and drawing an arc, etc. (imagine being startled by same and slipping off a ladder!) [if you want to be pedantic, you'd now remove the breaker] In what follows, recall that neutral and ground are essentially the same point, electrically. But, a short on neutral will appear differently than a short on ground -- if you are just looking at neutral and hot (instead of ground and hot). Having identified all of the outlets and fixtures that are on the circuit and knowing there is NO potential anywhere, you can now flip the DMM to the ohms scale and SURVEY the resistance between hot and neutral at each receptacle (no need to check both receptacles in a duplex outlet) and light fixture. Move to the most sensitive scale as you are looking for something in the 10 ohm or less range (for a short). Keep in mind that wire has resistance. E.g., 100 ft of #12AWG (for a 20A circuit) is ~0.16 ohms; #14AWG is ~0.25 ohms. Any "short" (which may be a dead short -- 0 ohms -- or a partial short (a few ohms) will appear to be LESS of a short the farther away you measure (because you will be ADDING the resistance of the wire between your measurement point and the actual location of the short TO the resistance of the actual short!) A C B --------------------------------------------+----------------- X --------------------------------------------+----------------- Short (at C) would appear as "X" ohms. When measured at B, it would appear as X plus twice the resistance of the wire from B to C (cuz you have to travel DOWN one wire and then back UP the other... twice the distance!) OTOH, when measured at A, the same reasoning shows how the measurement will be higher -- more wire involved! [You need a reasonably good meter (fluke will be fine) AND a solid connection to the conductors -- like the plug I described] By noting what the *exact* readings are at each point, you have a better chance of sorting out where it MIGHT be. (if the short is IN a Jbox, then you'll probably see damn close to 0.000 ohms, there!) Having verified that there is a short (low ohm connection when none is expected), you now have to isolate it. The above can help narrow it down to a range of "devices" (outlets/switches/fixtures). But, you'll eventually need to open up some Jboxes to see for sure. Eyes can spot burnt areas and loose wires pretty easily! Note that most devices have bare screw heads on each side. So, if the device has shifted position, it can bump into something that it shouldn't -- like the receptacle immediately adjacent, or the metal Jbox, etc. Some common sense will help you decide how the wire was *probably* strung. I.e., if two Jboxes are close by, then the wire probably goes from one to the other -- before heading across the room to some other Jbox. But, there are no guarantees : Once you have isolated a section of wire (which might be the entire circuit, if you are unlucky), you can save yourself some trouble by approaching the problem of breaking it into smaller segments logically. I.e., instead of isolating the receptacle at outlet #1 and retesting the balance of the circuit; then moving on to isolate outlet #2, and #3, and #4, etc. you can go to the outlet in the "middle" (take a guess) of the circuit and break the circuit at that point. Now, you have half of the circuit going off to the "left" and the other half going off to the "right". If the left half shows a short -- but the right doesn't -- then you now know the short is in the *left* half of the circuit. Likewise, if the right shows a short but not the left, then you know it's in the right half. So, you only have to check HALF of the outlets. Given the left/right half, you can now break *it* somewhere near the middle to eliminate half of *those*. Etc. A bit of thought will show that this will, on average, reduce the number of "breaks" that you have to make to isolate the short. You may encounter two issues that will complicate things. First, some folks use "back stab" devices. These are a labor saver in that you simply strip the wire and then jam it into a hole in the back of the device (switch/receptacle). It magically makes connection. But, it's a ratchet sort of action -- tugging on the wire won't remove it! You need to operate a "catch" that releases the "ratchet" (usually by slipping a cabinet tip screwdriver into a little slot/hole). [These things should be outlawed! : ] The other has to do with how the circuit is "daisy chained" on to the next device (Jbox) in the circuit. Receptacles tend to have a pair of screw terminals on each side -- two for the hot and two for the neutral. These are bonded together electrically with a metal bridge (it is fairly obvious). The natural inclination is to connect the "incoming" wires to one set of terminals (one hot and one neutral) and the "outgoing" wires to the other set. This effectively ties the incoming to the outgoing AT the receptacle. Instead, you might find the incoming tied directly to the outgoing with a wire nut. Then, a short "pigtail" connects the wire nut to the receptacle. In this way, the receptacle is not required for the circuit to continue on to the next device! As such, removing the wire from the receptacle will just isolate the receptacle from the circuit. It will *not* "break" the circuit at that point! What level of experience with electricity do you have? Same as anyone else I would think. I've wire-nutted replacement outlets a half dozen times. I've replaced a circuit breaker (220V for AC) only once. I put in a 3-way ceiling light once (put a box in the attic and dropped the wires down from between the wall to get to the switch). OK. So, you're probably comfortable working *in* the panel. For tools I have the basic yellow plug 3-light outlet tester. I have a red neon-light probe dumb tester. I can't find my Fluke DMM (but it's overkill usually). See my comments measuring wire resistance... The problem with the "simple" testers is they don't show you anything other than "working properly" or "working WRONGLY (in a bigtime way)". And, your personal "Comfort Factor"? How deep is your wallet? I.e., are you asking out of curiosity? Or, out of *need* (ABSOLUTELY can't afford to hire someone)? I can "afford" to waste my money on an electrician, but, I don't really have the money to spare. Plus, I'm only lacking in my debugging skills. Once I know what the problem is, I don't think the "fix" will be difficult. Understood. I just get nervous suggesting folks go poking around in a load/meter center or Jboxes. Note that you are operating in an "abnormal" situation; so, what you can EXPECT is no longer something that you can safely ASSUME. It's figuring out a strategy for finding the problem that I am asking help with - and - I think you boys gave me a pretty good start because I wasn't sure which way to go first since the stuff is all "hidden" in the walls. Think about what *could* have gone wrong. E.g., if you are frequently abusing a particular outlet, then it has seen more mechanical wear and tear than an outlet that is NEVER used, etc. What's LIKELY is best to pursue, initially. |
#20
Posted to alt.home.repair
|
|||
|
|||
Circuit breaker keeps tripping
On Wed, 20 Jan 2016 12:21:41 -0700, Don Y wrote:
Does the switch make *any* attempt to stay in the ON position? A short/overload on the circuit will cause the breaker to "trip" *AS* you are trying to turn it on! I.e., it will never really get into the ON position before you feel it going limp under your fingers. If, instead, it tries to catch but trips a second or two later, that's a slightly different story. It makes no attempt to catch. |
#21
Posted to alt.home.repair
|
|||
|
|||
Circuit breaker keeps tripping
On Wed, 20 Jan 2016 12:21:41 -0700, Don Y wrote:
And, it's NOT a GFCI circuit? And, it's a 120V line? Is the breaker a single breaker? Or, a "dual" (though NOT 220V)? I have no idea what the circuit is yet, but it has at least three built in switched lights on it. It's a single breaker (not ganged), but it seems to be in a dual package. Here it is in the off position (top right, 4th down, 15 amp). http://i65.tinypic.com/i5692c.jpg Here it trips the instant I try to set it to on. http://i66.tinypic.com/2ec2kol.jpg |
#22
Posted to alt.home.repair
|
|||
|
|||
Circuit breaker keeps tripping
On Wednesday, January 20, 2016 at 3:11:19 PM UTC-5, E. Robinson wrote:
On Wed, 20 Jan 2016 12:21:41 -0700, Don Y wrote: And, it's NOT a GFCI circuit? And, it's a 120V line? Is the breaker a single breaker? Or, a "dual" (though NOT 220V)? I have no idea what the circuit is yet, but it has at least three built in switched lights on it. It's a single breaker (not ganged), but it seems to be in a dual package. Here it is in the off position (top right, 4th down, 15 amp). http://i65.tinypic.com/i5692c.jpg Here it trips the instant I try to set it to on. http://i66.tinypic.com/2ec2kol.jpg If it makes no attempt to catch, it sounds like a mechanically bad breaker. You can trythis to confirm it..... without even removing the panel....... Turn off the main breaker. Now try to turn on the bad breaker. If it still does not catch even with the main off, the breaker is definilty bad. If it does catch with the main off then turn the main back on. If it immediatly trips, you may have a bad breaker or you may have a wiring fault. Now you need to remove the panel to troubleshoot further. When removing the panel, turn off the main breaker, wear rubber shoes or sneaks and stand on a carpet, and keep BOTH hands on the panel. What you don't want to do is have one hand on the panel and one hand on the box. This way, if you slip and the loose panel hits a live wire, you won't be shocked, but it may make a he** of a spark. M |
#23
Posted to alt.home.repair
|
|||
|
|||
Circuit breaker keeps tripping
"E. Robinson" wrote in message ... How do I debug when a circuit breaker keeps tripping? 1. It has never tripped before (years). 2. Yesterday, it was tripped. 3. I flip it back on, and it trips immediately. 4. It controls a bunch of outlets and lights and that's about it. I turn off the lights it controls. I unplug all the outlets. It still trips. How do you debug these things? One other thing that should not need to be said. When you flip it back on, did you turn it all the way to OFF before turning it back on ? This needs to be done to reset most breakers. |
#24
Posted to alt.home.repair
|
|||
|
|||
Circuit breaker keeps tripping
On Wed, 20 Jan 2016 12:42:43 -0500, Ralph Mowery wrote:
One other thing that should not need to be said. When you flip it back on, did you turn it all the way to OFF before turning it back on ? Good suggestion, but, yes, I instinctively did that, but, I just checked again, and it still flips immediately to the trip position. Here's a picture of it off. http://i65.tinypic.com/i5692c.jpg Here's a picture of it in the trip position. http://i66.tinypic.com/2ec2kol.jpg It's the breaker labeled "R" on the right (4 breakers down from the top). 15 amps. Seems to be "taped?" together with another one, which is independent. (Why the tape?) Maybe it's a non-ganged dual unit? |
#25
Posted to alt.home.repair
|
|||
|
|||
Circuit breaker keeps tripping
On 1/20/16 1:38 PM, E. Robinson wrote:
On Wed, 20 Jan 2016 12:42:43 -0500, Ralph Mowery wrote: Here's a picture of it in the trip position. http://i66.tinypic.com/2ec2kol.jpg It's the breaker labeled "R" on the right (4 breakers down from the top). 15 amps. Seems to be "taped?" together with another one, which is independent. (Why the tape?) Maybe it's a non-ganged dual unit? Looks like it is one of the "tandem" style, where you have 2 independent breakers in one "space" in the panel. Generally not used until the panel runs out of spaces. http://www.lowes.com/pd_8991-296-HOM... reaker+tandem |
#26
Posted to alt.home.repair
|
|||
|
|||
Circuit breaker keeps tripping
On Wed, 20 Jan 2016 07:04:53 -0000 (UTC), "E. Robinson"
wrote: It still trips. How do you debug these things? I'm not an electrician, so do not take my advice. I have a known good breaker that was removed from my HVAC disconnect box.. Reading, I saw you can test a breaker for continuity using a multi meter? Flipping the breaker off and on at the test bench. (single or double breakers) _How to Test a Circuit Breaker With a Multi meter _ http://www.ehow.com/how_4795794_test-circuit-breaker-multimeter.html Other reads: https://tinyurl.com/z6p3z78 |
#27
Posted to alt.home.repair
|
|||
|
|||
Circuit breaker keeps tripping
HOW ABOUT CALL ELECTRICIAN???
"E. Robinson" wrote in message ... How do I debug when a circuit breaker keeps tripping? 1. It has never tripped before (years). 2. Yesterday, it was tripped. 3. I flip it back on, and it trips immediately. 4. It controls a bunch of outlets and lights and that's about it. I turn off the lights it controls. I unplug all the outlets. It still trips. How do you debug these things? |
#28
Posted to alt.home.repair
|
|||
|
|||
Circuit breaker keeps tripping
On Wed, 20 Jan 2016 14:12:06 -0800, Tony944 wrote:
HOW ABOUT CALL ELECTRICIAN??? Why does this newsgroup exist if that's the answer? |
#29
Posted to alt.home.repair
|
|||
|
|||
Circuit breaker keeps tripping
On Thu, 21 Jan 2016 03:05:48 -0000 (UTC), "E. Robinson"
wrote: On Wed, 20 Jan 2016 14:12:06 -0800, Tony944 wrote: HOW ABOUT CALL ELECTRICIAN??? Why does this newsgroup exist if that's the answer? Because some of us know what we're doing. I'm always willing to assist others on this NG, but electricity can KILL. I read between the lines, and I can "read" their skill level, and I am not going to assist someone with killing themselves. This OP is clueless about basic electricity and should not be touching any wiring, PERIOD! I agree, CALL AN ELECTRICIAN ! If he was trying to replace a door, but showed the same lack of basic carpentry skills, I'd still be willing to assist, because doors dont kill people if they make a slight mistake. |
#31
Posted to alt.home.repair
|
|||
|
|||
Circuit breaker keeps tripping
On Wed, 20 Jan 2016 21:42:40 -0600, Paintedcow wrote:
This OP is clueless about basic electricity and should not be touching any wiring, PERIOD! Heh heh ... I'm a (retired) EE. So that's funny. BTW, if you know anything about electrical engineers, they typically don't learn anything practical (in school) about home wiring. It's all about poles and zeros and Kirchoff's law and fourier transforms and delta/Y transformers and Spice simulations and diffusion doping and Maxwell's equations and Coulomb's law and Faraday's Law and Ohm's law, and c=dv/dt and phase diagrams and polar plots, and cascade versus cascode configurations and emitters and gates, etc. Nothing whatsoever about typical mains wiring. |
#32
Posted to alt.home.repair
|
|||
|
|||
Circuit breaker keeps tripping
On 1/21/2016 1:30 AM, E. Robinson wrote:
On Wed, 20 Jan 2016 21:42:40 -0600, Paintedcow wrote: This OP is clueless about basic electricity and should not be touching any wiring, PERIOD! Heh heh ... I'm a (retired) EE. So that's funny. BTW, if you know anything about electrical engineers, they typically don't learn anything practical (in school) about home wiring. It's all about poles and zeros and Kirchoff's law and fourier transforms and delta/Y transformers and Spice simulations and diffusion doping and Maxwell's equations and Coulomb's law and Faraday's Law and Ohm's law, and c=dv/dt and phase diagrams and polar plots, and cascade versus cascode configurations and emitters and gates, etc. Perhaps, but then paintedcow knows a great deal about nothing and even when someone attempts to cure his ignorance, he doubles down and says something even more stupid. Do let us know the final outcome on this. With the additional details you've provided, it seems almost certain to be a circuit breaker that's simply given up the ghost. That said, I think there's usually a reason other than "its time has come"g for breakers to give up. Wondering if you've normally got enough of a load on that 15A circuit to heat it up and that that may have caused the failure. |
#33
Posted to alt.home.repair
|
|||
|
|||
Circuit breaker keeps tripping
On 1/21/2016 2:30 AM, E. Robinson wrote:
On Wed, 20 Jan 2016 21:42:40 -0600, Paintedcow wrote: This OP is clueless about basic electricity and should not be touching any wiring, PERIOD! Heh heh ... I'm a (retired) EE. So that's funny. BTW, if you know anything about electrical engineers, they typically don't learn anything practical (in school) about home wiring. It's all about poles and zeros and Kirchoff's law and fourier transforms and delta/Y transformers and Spice simulations and diffusion doping and Maxwell's equations and Coulomb's law and Faraday's Law and Ohm's law, and c=dv/dt and phase diagrams and polar plots, and cascade versus cascode configurations and emitters and gates, etc. Nothing whatsoever about typical mains wiring. I did meet a person like that. The electric light in his cellar wasn't working right. I got to show him how to shut the breaker, and replace a light switch. -- .. Christopher A. Young learn more about Jesus .. www.lds.org .. .. |
#34
Posted to alt.home.repair
|
|||
|
|||
Circuit breaker keeps tripping
On Thursday, January 21, 2016 at 2:30:31 AM UTC-5, E. Robinson wrote:
On Wed, 20 Jan 2016 21:42:40 -0600, Paintedcow wrote: This OP is clueless about basic electricity and should not be touching any wiring, PERIOD! Heh heh ... I'm a (retired) EE. So that's funny. BTW, if you know anything about electrical engineers, they typically don't learn anything practical (in school) about home wiring. It's all about poles and zeros and Kirchoff's law and fourier transforms and delta/Y transformers and Spice simulations and diffusion doping and Maxwell's equations and Coulomb's law and Faraday's Law and Ohm's law, and c=dv/dt and phase diagrams and polar plots, and cascade versus cascode configurations and emitters and gates, etc. Nothing whatsoever about typical mains wiring. Ohm's Law and all the rest of the basics don't apply to how to debug what amounts to a fancy switch? Good grief. |
#35
Posted to alt.home.repair
|
|||
|
|||
Circuit breaker keeps tripping
On 1/20/2016 10:05 PM, E. Robinson wrote:
On Wed, 20 Jan 2016 14:12:06 -0800, Tony944 wrote: HOW ABOUT CALL ELECTRICIAN??? Why does this newsgroup exist if that's the answer? Truly profound. I mean, like, I can totally relate. As a couple other folks have mentioned, it's good to have some basic understanding, and then come here for the details. For example, when I asked about adding hot or cold water to my floor model residential humidifier, I got told a lot of things, none of which answered my question. Sigh. Guess I can't win on that one. You did get some really good answers, including to just pull the breaker out and replace it, they often aren't that expensive. Also swap two black wires, and see if the problem follows the wire or the breaker. -- .. Christopher A. Young learn more about Jesus .. www.lds.org .. .. |
#36
Posted to alt.home.repair
|
|||
|
|||
Circuit breaker keeps tripping
On Thu, 21 Jan 2016 08:07:38 -0500, Stormin Mormon wrote:
You did get some really good answers, including to just pull the breaker out and replace it, they often aren't that expensive. Also swap two black wires, and see if the problem follows the wire or the breaker. The best answer was to shut the mains off, and then test the circuit breaker. That is a great test, and it showed the problem. |
#37
Posted to alt.home.repair
|
|||
|
|||
Circuit breaker keeps tripping
On Thursday, January 21, 2016 at 3:00:24 PM UTC-5, E. Robinson wrote:
On Thu, 21 Jan 2016 08:07:38 -0500, Stormin Mormon wrote: You did get some really good answers, including to just pull the breaker out and replace it, they often aren't that expensive. Also swap two black wires, and see if the problem follows the wire or the breaker. The best answer was to shut the mains off, and then test the circuit breaker. That is a great test, and it showed the problem. Great! And thanks for getting back to the group. One common scenario he the OP writes in with a problem, the group discusses back and forth, the OP disappears, the thread dies, the thread is resurrected 10 years later, the argument continues. Just a comment: the sooner you are sure what is wrong, the more you find it impossible to see contrary evidence. Troubleshooting is best with an open mind. And don't forget there can be a bad breaker AND a short. I looked up breaker longevity some time ago and don't remember the exact numbers, but they were in this neighborhood. A breaker can be turned on and off something like 30,000 times before it wears out. It can trip on mild overload maybe 1-3000 times. But a dead short drawing full available current will kill it in 1 to 2 times. |
#38
Posted to alt.home.repair
|
|||
|
|||
Circuit breaker keeps tripping
On 1/21/2016 3:00 PM, E. Robinson wrote:
The best answer was to shut the mains off, and then test the circuit breaker. That is a great test, and it showed the problem. Ah, so you had a loose neutral, then? Or was it some other problem? -- .. Christopher A. Young learn more about Jesus .. www.lds.org .. .. |
#39
Posted to alt.home.repair
|
|||
|
|||
Circuit breaker keeps tripping
"E. Robinson" writes:
On Wed, 20 Jan 2016 14:12:06 -0800, Tony944 wrote: HOW ABOUT CALL ELECTRICIAN??? Why does this newsgroup exist if that's the answer? For advice on the many thousands of things a homeowner is qualified to repair without danger. Electrical work isn't one of them. |
#40
Posted to alt.home.repair
|
|||
|
|||
Circuit breaker keeps tripping
On Thu, 21 Jan 2016 15:30:37 +0000, Scott Lurndal wrote:
For advice on the many thousands of things a homeowner is qualified to repair without danger. Electrical work isn't one of them. It's fixed. |
Reply |
|
Thread Tools | Search this Thread |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Forum | |||
Dryer keeps tripping the circuit breaker | Home Repair | |||
Circuit Breaker Tripping | Home Repair | |||
A/C Unit Keeps Tripping Circuit Breaker - How to test breaker before calling repair man? | Home Repair | |||
DC tripping circuit breaker | Woodworking | |||
a/c tripping circuit breaker | Electronics Repair |