Home |
Search |
Today's Posts |
|
Home Repair (alt.home.repair) For all homeowners and DIYers with many experienced tradesmen. Solve your toughest home fix-it problems. |
Reply |
|
LinkBack | Thread Tools | Display Modes |
#1
Posted to alt.home.repair
|
|||
|
|||
is there a special tool?
The girlfriend moved into a different home recently, so I am press-
ganged into service as a 'mr. fix-it' (sorta). The entrance way and a foyer area was covered with a ceramic tile and parquet flooring respectively, but the levels were higher than the rest of the flooring, so yanking it up, I found birch hardwood strip flooring that had been covered over. It perfectly matches all of the flooring in the bedrooms and rest of the hallway, so we'd like to preserve it. I have yanked up the parquet and the thin subflooring and some of the ceramic, but I see that they have small ring nails all over the place - presumably to stop squeeking in the hardwood? Anyway - I would like to remove these nails (they come out easily enough once the head can be gripped). For the most part they are in the 'groove' between the hardwood strips. If I use a nail puller, it will really chew it up a lot. Does anyone know if there is some sort of different tool available for situations such as this? Maybe like a really really thin 'prybar' that can be used to snag the nail heads? They are not recessed, but not quite enough showing enough to be grabbed. I was hoping someone who does this type of thing more frequently may have other ideas. Thanks! |
#2
Posted to alt.home.repair
|
|||
|
|||
is there a special tool?
Wonderbar?
Something like this: http://www.amazon.com/Stanley-55-526.../dp/B000A24RD4 or this: http://www.amazon.com/Stanley-55-525.../dp/B00002X22U wrote in message oups.com... The girlfriend moved into a different home recently, so I am press- ganged into service as a 'mr. fix-it' (sorta). The entrance way and a foyer area was covered with a ceramic tile and parquet flooring respectively, but the levels were higher than the rest of the flooring, so yanking it up, I found birch hardwood strip flooring that had been covered over. It perfectly matches all of the flooring in the bedrooms and rest of the hallway, so we'd like to preserve it. I have yanked up the parquet and the thin subflooring and some of the ceramic, but I see that they have small ring nails all over the place - presumably to stop squeeking in the hardwood? Anyway - I would like to remove these nails (they come out easily enough once the head can be gripped). For the most part they are in the 'groove' between the hardwood strips. If I use a nail puller, it will really chew it up a lot. Does anyone know if there is some sort of different tool available for situations such as this? Maybe like a really really thin 'prybar' that can be used to snag the nail heads? They are not recessed, but not quite enough showing enough to be grabbed. I was hoping someone who does this type of thing more frequently may have other ideas. Thanks! |
#3
Posted to alt.home.repair
|
|||
|
|||
is there a special tool?
On Tue, 17 Jul 2007 04:35:58 -0700, "
wrote: The girlfriend moved into a different home recently, so I am press- ganged into service as a 'mr. fix-it' (sorta). The entrance way and a foyer area was covered with a ceramic tile and parquet flooring respectively, but the levels were higher than the rest of the flooring, so yanking it up, I found birch hardwood strip flooring that had been covered over. It perfectly matches all of the flooring in the bedrooms and rest of the hallway, so we'd like to preserve it. I have yanked up the parquet and the thin subflooring and some of the ceramic, but I see that they have small ring nails all over the place - presumably to stop squeeking in the hardwood? Anyway - I would like to remove these nails (they come out easily enough once the head can be gripped). For the most part they are in the 'groove' between the hardwood strips. If I use a nail puller, it will really chew it up a lot. Does anyone know if there is some sort of different tool available for situations such as this? Maybe like a really really thin 'prybar' that can be used to snag the nail heads? They are not recessed, but not quite enough showing enough to be grabbed. I was hoping someone who does this type of thing more frequently may have other ideas. Thanks! Vise Grips. --Andy Asberry-- ------Texas----- |
#4
Posted to alt.home.repair
|
|||
|
|||
is there a special tool?
On Jul 17, 7:35 am, " wrote:
The girlfriend moved into a different home recently, so I am press- ganged into service as a 'mr. fix-it' (sorta). The entrance way and a foyer area was covered with a ceramic tile and parquet flooring respectively, but the levels were higher than the rest of the flooring, so yanking it up, I found birch hardwood strip flooring that had been covered over. It perfectly matches all of the flooring in the bedrooms and rest of the hallway, so we'd like to preserve it. I have yanked up the parquet and the thin subflooring and some of the ceramic, but I see that they have small ring nails all over the place - presumably to stop squeeking in the hardwood? Anyway - I would like to remove these nails (they come out easily enough once the head can be gripped). For the most part they are in the 'groove' between the hardwood strips. If I use a nail puller, it will really chew it up a lot. Does anyone know if there is some sort of different tool available for situations such as this? Maybe like a really really thin 'prybar' that can be used to snag the nail heads? They are not recessed, but not quite enough showing enough to be grabbed. I was hoping someone who does this type of thing more frequently may have other ideas. Thanks! Best thing that worked for me was to take a pair of cobblers pliers and belt sand the outside flush so that there is only a bevel on the inside. You might be able to raise them with diagonal gutters also. |
#5
Posted to alt.home.repair
|
|||
|
|||
is there a special tool?
" wrote in
oups.com: The girlfriend moved into a different home recently, so I am press- ganged into service as a 'mr. fix-it' (sorta). The entrance way and a foyer area was covered with a ceramic tile and parquet flooring respectively, but the levels were higher than the rest of the flooring, so yanking it up, I found birch hardwood strip flooring that had been covered over. It perfectly matches all of the flooring in the bedrooms and rest of the hallway, so we'd like to preserve it. I have yanked up the parquet and the thin subflooring and some of the ceramic, but I see that they have small ring nails all over the place - presumably to stop squeeking in the hardwood? Anyway - I would like to remove these nails (they come out easily enough once the head can be gripped). For the most part they are in the 'groove' between the hardwood strips. If I use a nail puller, it will really chew it up a lot. Does anyone know if there is some sort of different tool available for situations such as this? Maybe like a really really thin 'prybar' that can be used to snag the nail heads? They are not recessed, but not quite enough showing enough to be grabbed. I was hoping someone who does this type of thing more frequently may have other ideas. Thanks! Your girlfriend found a solution to her fix-it problems :-) |
#6
Posted to alt.home.repair
|
|||
|
|||
is there a special tool?
On Tue, 17 Jul 2007 18:32:25 -0500, Al Bundy
wrote: Your girlfriend found a solution to her fix-it problems :-) I don't see the nexus with the problem or solution :-) -- Oren "The voices in my head may not be real, but they have some good ideas!" |
#8
Posted to alt.home.repair
|
|||
|
|||
is there a special tool?
"Robert Allison" wrote in message news:BSeni.1030$I76.988@trnddc05... wrote: The girlfriend moved into a different home recently, so I am press- ganged into service as a 'mr. fix-it' (sorta). The entrance way and a foyer area was covered with a ceramic tile and parquet flooring respectively, but the levels were higher than the rest of the flooring, so yanking it up, I found birch hardwood strip flooring that had been covered over. It perfectly matches all of the flooring in the bedrooms and rest of the hallway, so we'd like to preserve it. I have yanked up the parquet and the thin subflooring and some of the ceramic, but I see that they have small ring nails all over the place - presumably to stop squeeking in the hardwood? Anyway - I would like to remove these nails (they come out easily enough once the head can be gripped). For the most part they are in the 'groove' between the hardwood strips. If I use a nail puller, it will really chew it up a lot. Does anyone know if there is some sort of different tool available for situations such as this? Maybe like a really really thin 'prybar' that can be used to snag the nail heads? They are not recessed, but not quite enough showing enough to be grabbed. I was hoping someone who does this type of thing more frequently may have other ideas. Thanks! Flat bars or wonder bars are the tool for this job. I would get a small flat piece of metal to help in protection of the floor boards. You can use the tops of steel cans for this or a flattened can (like corn and green beens come in) to lay on the floor under the pry bar. I have had good luck with restorers bars or bars like these: http://tinyurl.com/3ylnvb By ring nails, I assume you mean the large-head ring shank like used for siding? I'll second the wonder bar recomendation. Stanley makes a tiny one, plated finish so it doesn't stain the work, that would be perfect for this. I'd also buy a sacrificial good quality 1" putty knife, for the ones the wonder bar won't get under. A piece of cardboard or plastic under the fulcrum point will reduce the dents in the wood. No matter what, it is gonna leave marks, but you already have the dents from the heads to sand out/fill amyway. After the first 4 or 5, you will get the hang of it. Other alternative- a good center punch and a six-pack of sharp bits. Dimple each nail, drill the head till it detaches from the shaft, and then sink with the punch and putty over, if needed. aem sends... |
#9
Posted to alt.home.repair
|
|||
|
|||
is there a special tool?
On Jul 17, 7:35 am, " wrote:
The girlfriend moved into a different home recently, so I am press- ganged into service as a 'mr. fix-it' (sorta). The entrance way and a foyer area was covered with a ceramic tile and parquet flooring respectively, but the levels were higher than the rest of the flooring, so yanking it up, I found birch hardwood strip flooring that had been covered over. It perfectly matches all of the flooring in the bedrooms and rest of the hallway, so we'd like to preserve it. I have yanked up the parquet and the thin subflooring and some of the ceramic, but I see that they have small ring nails all over the place - presumably to stop squeeking in the hardwood? Anyway - I would like to remove these nails (they come out easily enough once the head can be gripped). For the most part they are in the 'groove' between the hardwood strips. If I use a nail puller, it will really chew it up a lot. Does anyone know if there is some sort of different tool available for situations such as this? Maybe like a really really thin 'prybar' that can be used to snag the nail heads? They are not recessed, but not quite enough showing enough to be grabbed. I was hoping someone who does this type of thing more frequently may have other ideas. Thanks! I should have mentioned that the adjoining areas have been tinted different colours, so she intends to get someone in to resand and refinish the flooring. When I had mine done the guy used the sawdust from the first coat mixed with the filler and went over the entire floor surface with it - it worked wonders and essentially hid all the holes and imperfections, etc. that I had in mine. So it does not have to be a perfectly marr-less (is that a word?), solution but I am defintely trying to minimize the damage. Thank you all for the wonderful ideas and links. I'll be ferreting about to see what I can find from these sources. regards. (hi-ho, hi-ho .....) |
#10
Posted to alt.home.repair
|
|||
|
|||
is there a special tool?
wrote in message ups.com... I should have mentioned that the adjoining areas have been tinted different colours, so she intends to get someone in to resand and refinish the flooring. When I had mine done the guy used the sawdust from the first coat mixed with the filler and went over the entire floor surface with it - it worked wonders and essentially hid all the holes and imperfections, etc. that I had in mine. So it does not have to be a perfectly marr-less (is that a word?), solution but I am defintely trying to minimize the damage. Thank you all for the wonderful ideas and links. I'll be ferreting about to see what I can find from these sources. regards. (hi-ho, hi-ho .....) I'd maybe try a Dremel with a cutoff wheel. Just cut the nails off at the surface, then if possible pound them in further with a nail set & hammer. Fill the holes, or maybe the refinisher will do that. |
#11
Posted to alt.home.repair
|
|||
|
|||
is there a special tool?
clipped
I should have mentioned that the adjoining areas have been tinted different colours, so she intends to get someone in to resand and refinish the flooring. When I had mine done the guy used the sawdust from the first coat mixed with the filler and went over the entire floor surface with it - it worked wonders and essentially hid all the holes and imperfections, etc. that I had in mine. So it does not have to be a perfectly marr-less (is that a word?), solution but I am defintely trying to minimize the damage. Thank you all for the wonderful ideas and links. I'll be ferreting about to see what I can find from these sources. regards. (hi-ho, hi-ho .....) I have read about using sawdust to patch holes. Can you use a small grinder .. Dremel bit .. to cut the nailheads down? Fill with small wood plugs prior to sanding or with sawdust afterward. |
#12
Posted to alt.home.repair
|
|||
|
|||
is there a special tool?
On Jul 17, 6:35 am, " wrote:
The girlfriend moved into a different home recently, so I am press- ganged into service as a 'mr. fix-it' (sorta). The entrance way and a foyer area was covered with a ceramic tile and parquet flooring respectively, but the levels were higher than the rest of the flooring, so yanking it up, I found birch hardwood strip flooring that had been covered over. It perfectly matches all of the flooring in the bedrooms and rest of the hallway, so we'd like to preserve it. I have yanked up the parquet and the thin subflooring and some of the ceramic, but I see that they have small ring nails all over the place - presumably to stop squeeking in the hardwood? Anyway - I would like to remove these nails (they come out easily enough once the head can be gripped). For the most part they are in the 'groove' between the hardwood strips. If I use a nail puller, it will really chew it up a lot. Does anyone know if there is some sort of different tool available for situations such as this? Maybe like a really really thin 'prybar' that can be used to snag the nail heads? They are not recessed, but not quite enough showing enough to be grabbed. I was hoping someone who does this type of thing more frequently may have other ideas. Thanks! Besides the numerous types of nail pullers at Amazon.com, there is this new and different sort at Hartvilletool.com that you might want to look at: Cat. No. 74668. At $24.99 it is more than some, but I bought it for pulling finishing nails backward out of trim moulding so it can be reused and it is nice heavy duty tool for that. HTH Joe |
#13
Posted to alt.home.repair
|
|||
|
|||
is there a special tool?
Your letter confuses me, but can you just nail them in farther. With a nail set or something. On Tue, 17 Jul 2007 04:35:58 -0700, " wrote: The girlfriend moved into a different home recently, so I am press- ganged into service as a 'mr. fix-it' (sorta). The entrance way and a foyer area was covered with a ceramic tile and parquet flooring respectively, but the levels were higher than the rest of the flooring, so yanking it up, I found birch hardwood strip flooring that had been covered over. It perfectly matches all of the flooring in the bedrooms and rest of the hallway, so we'd like to preserve it. I have yanked up the parquet and the thin subflooring and some of the ceramic, but I see that they have small ring nails all over the place - presumably to stop squeeking in the hardwood? Anyway - I would like to remove these nails (they come out easily enough once the head can be gripped). For the most part they are in the 'groove' between the hardwood strips. If I use a nail puller, it will really chew it up a lot. Does anyone know if there is some sort of different tool available for situations such as this? Maybe like a really really thin 'prybar' that can be used to snag the nail heads? They are not recessed, but not quite enough showing enough to be grabbed. I was hoping someone who does this type of thing more frequently may have other ideas. Thanks! |
Reply |
Thread Tools | Search this Thread |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Forum | |||
Powered crimping tool equivalent to COPALUM tool | Home Ownership | |||
A Special Tool | Woodworking | |||
Need Special Tool - Any Leads? | Metalworking | |||
Shelf sockets - special tool for insertion? | Woodworking |