Seán O'Leathlóbhair wrote:

I am not sure if this is an appropriate group for this question. If
not, please suggest a better one.

I have a light in the house which I have wanted to switch to a low
energy bulb for a long time. The hold up was that I needed a very
small bulb. At last, I have found a small enough bulb but something
odd occurred as soon as I put it in.

When it is switched on, it works as expected.

When it is switched off, it blinks every few seconds. So, I guess
that there must be a problem with the switch If it is passing nothing
then it would seem impossible for the bulb to do anything. I did not
notice any problem with the previous incandescent bulb but I guess
that if the switch is leaking a tiny amount, the filament would glow
too little to be seen.

I have a few questions:

What is going on? Is a tiny current leaking, building up a charge in
a capacitor somewhere until a sufficient voltage builds up to spark in
the bulb and discharge the capacitor, and then the cycle repeats.

Is it safe?

Will it wear out the bulb very fast?

Is it likely to be enough to replace the switch? (Actually three
switches can turn this bulb on and off).

Might I have to replace the wiring? (Much harder than just replacing
the switches)

--
Seán Ó Leathlóbhair

This has come up before in aus.electronics though I don't recall if there
was a definite cure for it.

Chris

Chris Jones wrote:
Seán O'Leathlóbhair wrote:

I am not sure if this is an appropriate group for this question. If
not, please suggest a better one.

I have a light in the house which I have wanted to switch to a low
energy bulb for a long time. The hold up was that I needed a very
small bulb. At last, I have found a small enough bulb but something
odd occurred as soon as I put it in.

When it is switched on, it works as expected.

When it is switched off, it blinks every few seconds. So, I guess
that there must be a problem with the switch If it is passing nothing
then it would seem impossible for the bulb to do anything. I did not
notice any problem with the previous incandescent bulb but I guess
that if the switch is leaking a tiny amount, the filament would glow
too little to be seen.

I have a few questions:

What is going on? Is a tiny current leaking, building up a charge in
a capacitor somewhere until a sufficient voltage builds up to spark in
the bulb and discharge the capacitor, and then the cycle repeats.

Is it safe?

Will it wear out the bulb very fast?

Is it likely to be enough to replace the switch? (Actually three
switches can turn this bulb on and off).

Might I have to replace the wiring? (Much harder than just replacing
the switches)

--
Seán Ó Leathlóbhair

This has come up before in aus.electronics though I don't recall if there
was a definite cure for it.

Thanks. If there is no danger, I don't need a cure. The flash is not
irritating. The CO detector nearby flashes more brightly. I am just
worried that it is telling me that something nasty is wrong with my
wiring.

--
Seán Ó Leathlóbhair

"Seán O'Leathlóbhair" wrote in message
ups.com...
Chris Jones wrote:
Seán O'Leathlóbhair wrote:

I am not sure if this is an appropriate group for this question. If
not, please suggest a better one.

I have a light in the house which I have wanted to switch to a low
energy bulb for a long time. The hold up was that I needed a very
small bulb. At last, I have found a small enough bulb but something
odd occurred as soon as I put it in.

When it is switched on, it works as expected.

When it is switched off, it blinks every few seconds. So, I guess
that there must be a problem with the switch If it is passing nothing
then it would seem impossible for the bulb to do anything. I did not
notice any problem with the previous incandescent bulb but I guess
that if the switch is leaking a tiny amount, the filament would glow
too little to be seen.

I have a few questions:

What is going on? Is a tiny current leaking, building up a charge in
a capacitor somewhere until a sufficient voltage builds up to spark in
the bulb and discharge the capacitor, and then the cycle repeats.

Is it safe?

Will it wear out the bulb very fast?

Is it likely to be enough to replace the switch? (Actually three
switches can turn this bulb on and off).

Might I have to replace the wiring? (Much harder than just replacing
the switches)

--
Seán Ó Leathlóbhair

This has come up before in aus.electronics though I don't recall if there
was a definite cure for it.

Thanks. If there is no danger, I don't need a cure. The flash is not
irritating. The CO detector nearby flashes more brightly. I am just
worried that it is telling me that something nasty is wrong with my
wiring.

--
Seán Ó Leathlóbhair



It'll probably cause the CFL to fail much sooner than it otherwise would.
I'd check the wiring and switches just because it's easy to do, make sure
there isn't any moist gunk between contacts or anything else like that.
Another option is to wire a small incandescent bulb such as a nightlight in
parallel but this is not always practical.