Woodworking (rec.woodworking) Discussion forum covering all aspects of working with wood. All levels of expertise are encouraged to particiapte.

Reply
 
LinkBack Thread Tools Search this Thread Display Modes
  #1   Report Post  
Dan
 
Posts: n/a
Default Article in Woodsmith # 76

Hello all;

I am looking for an article on a chair seat scooping jig. I believe it
is in Woodsmith #76. I believe it uses either a skilsaw or router to
scoop out the seat for a windsor chair. If anyone has a copy of the
article, would you check to see if that is what it is about?

Thank you in advance,

Dan Harriman
Orange, Texas
email is woodworkerdan at yahoo dot com
  #2   Report Post  
Larry Jaques
 
Posts: n/a
Default

On Sun, 21 Nov 2004 03:05:20 GMT, Dan calmly
ranted:

Hello all;

I am looking for an article on a chair seat scooping jig. I believe it
is in Woodsmith #76. I believe it uses either a skilsaw or router to
scoop out the seat for a windsor chair. If anyone has a copy of the
article, would you check to see if that is what it is about?


Why go Normite when you can happily Neander this one, Dan?

Hey, all you need is this lovely little bronze tool:
http://www.japanwoodworker.com/produ...ept _id=12045

or a travisher:
http://www.japanwoodworker.com/produ...ept _id=11847

or a scorp, and this one's a great deal:
http://www.craftsmanstudio.com/html_p/L5002250.htm

or an adze:
http://www.wisementrading.com/woodworking/gransfors.htm #1248
http://www.japanwoodworker.com/produ...ep t_id=11556


-- Friends Don't Let Friends Eat Turkey and Drive --

  #3   Report Post  
Dan
 
Posts: n/a
Default

Larry Jaques wrote in
:

On Sun, 21 Nov 2004 03:05:20 GMT, Dan calmly
ranted:

Hello all;

I am looking for an article on a chair seat scooping jig. I
believe it is in Woodsmith #76.


Why go Normite when you can happily Neander this one, Dan?


hehehe, good point Larry! I actually saw Norm using those very tools
this past weekend. He is making a Windsor chair. I think that I may
have seen a bead or two of sweat coming from his brow when he was
using them!

I have found the article and it wasn't what I was looking for anyway.
It shows how to hollow out the seat for a shop stool.

Take care and make more sawdust,

Dan Harriman
Orange, Texas
  #4   Report Post  
Larry Jaques
 
Posts: n/a
Default

On Tue, 23 Nov 2004 15:17:49 GMT, Dan calmly
ranted:

Larry Jaques wrote in


Why go Normite when you can happily Neander this one, Dan?


hehehe, good point Larry! I actually saw Norm using those very tools
this past weekend. He is making a Windsor chair. I think that I may
have seen a bead or two of sweat coming from his brow when he was
using them!


Amazing! Did you record that? Nobody'll believe you.


I have found the article and it wasn't what I was looking for anyway.
It shows how to hollow out the seat for a shop stool.


Iffen ya wants ta go the Normite route, pick up one of the King Arthur
Tools Lancelot disc. It's a 4-1/2" diameter chainsaw. (Ar ar ar)
Ditto the Arbortec discs and Kutzall carbide discs.


Take care and make more sawdust,


I'm finally out there doing that and it feels good.

---
Is it time for your medication or mine?
http://diversify.com Custom Website Applications

  #5   Report Post  
patriarch
 
Posts: n/a
Default


I have found the article and it wasn't what I was looking for anyway.
It shows how to hollow out the seat for a shop stool.


Iffen ya wants ta go the Normite route, pick up one of the King Arthur
Tools Lancelot disc. It's a 4-1/2" diameter chainsaw. (Ar ar ar)
Ditto the Arbortec discs and Kutzall carbide discs.

You can also buy a rubber-backed sanding disk for the DeWalt Low Angle
grinder. When loaded with 24 grit, it's _almost_ as agressive as the
Lancelot, and slightly safer. Think high power rasp. Available at the
BORG. Cheap!

LOTS of fun. Use outside, or clean up the dust for hours.

Just please don't carve another bear from a log, though. It's been done
already.

Patriarch


  #6   Report Post  
Andy Dingley
 
Posts: n/a
Default

On Tue, 23 Nov 2004 19:34:37 -0800, Larry Jaques
wrote:

pick up one of the King Arthur Tools Lancelot disc.
It's a 4-1/2" diameter chainsaw. (Ar ar ar)


NFW !!!

Ditto the Arbortec discs and Kutzall carbide discs.


Haven't used a Kutzall. The Arbortech is _much_ safer to handle than a
Lancelot - my favoured power tool for hollowing seat bases, and life's
too short and tiresome already to carve an arse-rest in an elm seat
base using a scorp and curved drawknife.

The chainsaws disks have a vicious tendency to kick back. The
Arbortech has different shaped teeth and doesn't do this. It's still
terrifying, but only in a good way.



--
Socialism: Eric, not Tony
  #7   Report Post  
Paul Kierstead
 
Posts: n/a
Default

In article ,
Andy Dingley wrote:

life's
too short and tiresome already to carve an arse-rest in an elm seat
base using a scorp and curved drawknife.


I watched a fellow (David Ambrose I believe) do this using a scorp,
drawknife and shave and he did it *amazingly* fast; I am not entirely
sure it could be done faster with a non-automated power tool. Mind you
he uses Pine for the seat.
  #8   Report Post  
Larry Jaques
 
Posts: n/a
Default

On Fri, 26 Nov 2004 03:27:42 +0000, Andy Dingley
calmly ranted:

On Tue, 23 Nov 2004 19:34:37 -0800, Larry Jaques
wrote:

pick up one of the King Arthur Tools Lancelot disc.
It's a 4-1/2" diameter chainsaw. (Ar ar ar)


NFW !!!


Wuss! g


Ditto the Arbortec discs and Kutzall carbide discs.


Haven't used a Kutzall. The Arbortech is _much_ safer to handle than a
Lancelot - my favoured power tool for hollowing seat bases, and life's
too short and tiresome already to carve an arse-rest in an elm seat
base using a scorp and curved drawknife.


One could lose 2 pounds (weight, not Brit money) doing so, though.
It's both good exercise physically and a good hand/eye coordination
test.


The chainsaws disks have a vicious tendency to kick back. The
Arbortech has different shaped teeth and doesn't do this. It's still
terrifying, but only in a good way.


Chainsaw teeth have anti-kickback rails shaped very much like the
Arbortec discs. If Arbortec's products weren't double that price,
I'd have one already. Both are equally dangerous, much like every
other tool we own. This is a dangerous hobby.


--------------------------------------
PESSIMIST: An optimist with experience
--------------------------------------------
www.diversify.com - Web Database Development

  #9   Report Post  
Larry Bud
 
Posts: n/a
Default

Larry Jaques wrote in message . ..
On Sun, 21 Nov 2004 03:05:20 GMT, Dan calmly
ranted:

Hello all;

I am looking for an article on a chair seat scooping jig. I believe it
is in Woodsmith #76. I believe it uses either a skilsaw or router to
scoop out the seat for a windsor chair. If anyone has a copy of the
article, would you check to see if that is what it is about?


Why go Normite when you can happily Neander this one, Dan?



some of us have to get the presents done by Christmas!
Reply
Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules

Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
easy money Onemoredrunk Home Ownership 0 October 11th 04 01:00 AM
Please Help Find Magazine Article Gredo Goldenstein Woodworking 5 September 18th 03 11:15 AM


All times are GMT +1. The time now is 09:08 PM.

Powered by vBulletin® Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004-2024 DIYbanter.
The comments are property of their posters.
 

About Us

"It's about DIY & home improvement"