Opinions, please.
NOT a Domino, but look at the price!
Credible manufacturer to boot.

http://busybeetools.ca/cgi-bin/pictu...TITEM=TC500DWL

"Robatoy" wrote in message
...
Opinions, please.
NOT a Domino, but look at the price!
Credible manufacturer to boot.

http://busybeetools.ca/cgi-bin/pictu...TITEM=TC500DWL

Does not show up at tritontools.com BUT I wonder how far apart the drill
are.. May not be suitable for face frames or rail and stile cabinet doors.

On Sat, 12 Jun 2010 10:31:53 -0500, Leon wrote:

"Robatoy" wrote in message
news:4cfa0b14-cdeb-432f-
...
Opinions, please.
NOT a Domino, but look at the price!
Credible manufacturer to boot.

http://busybeetools.ca/cgi-bin/pictu...TITEM=TC500DWL

Does not show up at tritontools.com BUT I wonder how far apart the
drill are.. May not be suitable for face frames or rail and stile
cabinet doors.

Web site that I found lists the drills has being 32mm between centers.

On Sat, 12 Jun 2010 17:45:59 GMT, "Paul T."
wrote:

Web site that I found lists the drills has being 32mm between centers.

Basically, it's about 1.25 inches which could be considered suitable
for the average rail and stile face frame of 2 inches?

On 6/12/10 1:02 PM, Upscale wrote:
On Sat, 12 Jun 2010 17:45:59 GMT, "Paul
wrote:

Web site that I found lists the drills has being 32mm between centers.

Basically, it's about 1.25 inches which could be considered suitable
for the average rail and stile face frame of2 inches?

Probably comes with a jig attachment for shelf pins, too.


--

-MIKE-

"Playing is not something I do at night, it's my function in life"
--Elvin Jones (1927-2004)
--
http://mikedrums.com

---remove "DOT" ^^^^ to reply

On Sat, 12 Jun 2010 13:05:30 -0500, -MIKE-
wrote:

Probably comes with a jig attachment for shelf pins, too.

That might be a handy tool if some sort of incremental jig attachment
was formulated for shelf pins, except for the cost of the tool over a
simple jig.

I've always just marked shelf pin holes with a ruler and pencil and
then gone at them with a forstner bit and a piece of tap to indicate
depth. Guess I'm too cheap to buy a manufactured jig of some sort.
Admittedly, I've been fortunate not to blast through some project
coming out the finished side.

"Paul T." wrote in message
...
On Sat, 12 Jun 2010 10:31:53 -0500, Leon wrote:

"Robatoy" wrote in message
news:4cfa0b14-cdeb-432f-
...
Opinions, please.
NOT a Domino, but look at the price!
Credible manufacturer to boot.

http://busybeetools.ca/cgi-bin/pictu...TITEM=TC500DWL

Does not show up at tritontools.com BUT I wonder how far apart the
drill are.. May not be suitable for face frames or rail and stile
cabinet doors.

Web site that I found lists the drills has being 32mm between centers.


Yeah, that would be a bit too wide for face frames. 32mm OC is about 1.25"
OC and then add at least .25" for the radius of the two dowels and if not
perfectly centered on a 1.5" wide face frame you would have a blow out on
one side or the other. I'd say a minimum of 2" for the face frames.

"Leon" wrote in message
...

"Paul T." wrote in message
...
On Sat, 12 Jun 2010 10:31:53 -0500, Leon wrote:

"Robatoy" wrote in message
news:4cfa0b14-cdeb-432f-
...
Opinions, please.
NOT a Domino, but look at the price!
Credible manufacturer to boot.

http://busybeetools.ca/cgi-bin/pictu...TITEM=TC500DWL

Does not show up at tritontools.com BUT I wonder how far apart the
drill are.. May not be suitable for face frames or rail and stile
cabinet doors.

Web site that I found lists the drills has being 32mm between centers.


Yeah, that would be a bit too wide for face frames. 32mm OC is about
1.25" OC and then add at least .25" for the radius of the two dowels and
if not perfectly centered on a 1.5" wide face frame you would have a blow
out on one side or the other. I'd say a minimum of 2" for the face
frames.


AAMOF the face frames in my kitchen are 1.75", it would not have worked on
them.