Home |
Search |
Today's Posts |
|
Woodworking (rec.woodworking) Discussion forum covering all aspects of working with wood. All levels of expertise are encouraged to particiapte. |
Reply |
|
|
LinkBack | Thread Tools | Display Modes |
#41
Posted to rec.woodworking
|
|||
|
|||
Renamed: CNC Machine
On Nov 9, 6:21*pm, Morris Dovey wrote:
WTF? The rendering at the top of the page shows two x-axis steppers and a z-axis stepper and right below it is a 3-motor kit. How about a y-axis stepper? Hmmm... what I see, is 2 y axis steppers, one z axis stepper and no X axis stepper. Okay, I'm being a dick here... but for me, I operate the table from the end, so the long axis is Y, the across axis is X. I do have another settings file which flips everything 90 degrees...but my brain doesn't work that way..for some reason. I have said this before... I don't think like other people. G |
#43
Posted to rec.woodworking
|
|||
|
|||
Renamed: CNC Machine
On Nov 9, 8:43*pm, Morris Dovey wrote:
[snipped some good advice from Morris for Dave.] but wait! There's more! Be warned that this CNC stuff can make you lose sleep, think weird thoughts, and twist your sense of humor in strange ways. If you haven't seen the video of robatoy's chicken spinner, you should. I, myself, have kept most of my marbles in the basket - but I'm still working on my weapons-grade CNC pie thrower... Which begs the questions: "What kind of pie?" and "How far?" I'm surprised jo4hn isn't doing the CNC boogie yet. He's used to talking to parcels full of electronics from far, far awaaaayyy! |
#44
Posted to rec.woodworking
|
|||
|
|||
Renamed: CNC Machine
On Nov 9, 7:00*pm, wrote:
On Mon, 09 Nov 2009 17:35:58 -0500, Greg wrote: said: I'm not Robatoy, but note that the listed $520 price does not include many relatively expensive parts such as the ACME drive shafts, zero backlash compensating drive nuts and mount, shaft couplers, guide Understood and knew all that. What I showed may have only covered 25%-50% needed parts list. What I really want to know is if the type of stuff I did link too were of sufficient quality to begin build what one would consider to be an above average CNC machine. Guess the question should have been do these parts qualify as a really decent starting point or should I be aiming higher? I find these places helpful: http://www.cnczone.com/ http://www.vectric.com/forum/ http://www.talkshopbot.com/forum/discus.cgi |
#45
Posted to rec.woodworking
|
|||
|
|||
Renamed: CNC Machine
On Mon, 9 Nov 2009 17:29:05 -0800 (PST), Robatoy
wrote: You can have a lot of fun for $3K US.. http://www.rockler.com/product.cfm?p...ource=googleps. Comes with Vectric V-Carve Pro (Aspire's kid brother) As Greg pointed out, you're nowhere near done by buying that kit. The rest really adds up in a hurry. Looks like a nice unit, but I'd prefer to build one myself considering that all the parts, pieces and documentation are available. It's the best way for me to learn. |
#46
Posted to rec.woodworking
|
|||
|
|||
Renamed: CNC Machine
On Mon, 09 Nov 2009 19:43:01 -0600, Morris Dovey
wrote: Think weird thoughts No problem, do that already. and twist your sense of humor in strange ways. Don't have one as many people here will attest to. kept most of my marbles in the basket - but I'm still working on my weapons-grade CNC pie thrower... You mean how to create a CNC built pie trebuchet? |
#47
Posted to rec.woodworking
|
|||
|
|||
Some results of experimenting with soap stone. (Prelude tocarving details in wood.)
On Nov 9, 6:39*pm, Morris Dovey wrote:
Robatoy wrote: On Nov 9, 4:47 pm, Morris Dovey wrote: Robatoy wrote: On Nov 9, 12:27 pm, Greg wrote: I have a question - do customers actually want details of this sort engraved into their countertops or was this an experiment to test the limits of what could be done? Both. So far I have been lucky to get paid for the challenges I have wrestled to the ground. You're being improperly modest. Do you still have the photos of your backlit inlay work? Would you post a link, please? -- Morris Dovey DeSoto Solar DeSoto, Iowa USAhttp://www.iedu.com/DeSoto/ You mean this ol' thing? http://i123.photobucket.com/albums/o...oy/Backlit.jpg Wow! No. ;-) I was speaking of v-grooved and filled piece with LED backlighting. That lithophane looks pretty good, tho - and I think you snuck in a sawhorse drive-by. Au contraire, mon frère. That saw-horse is a Triton which I mini- reviewed quite some time ago. I dunno how I lived without it. Handiest thing ever. Handier than a bag of potato chips, handier than a pocket on a shirt. -- Morris Dovey DeSoto Solar DeSoto, Iowa USAhttp://www.iedu.com/DeSoto/ |
#48
Posted to rec.woodworking
|
|||
|
|||
Some results of experimenting with soap stone. (Prelude to carving details in wood.)
"Morris Dovey" wrote in message
... diggerop wrote: "Robatoy" wrote in message ... On Nov 9, 11:16 am, "diggerop" toobusy@themoment wrote: "Robatoy" wrote in message ... 3HP spindle on a 1/16" ball nose bit. 2"/second feed rate. That gets kind of hairy as soapstone can have some hard veins in it. The goal of this experiment was to get acceptable detail at fast cutting/feed rates. Detail can be increased by smaller step-over rates. I'm reasonably satisfied. After cutting, I coated the stone with FrogJuice. A clear coating out of a rattle can. http://s123.photobucket.com/albums/o...=view¤t=... http://i123.photobucket.com/albums/o...y/Detail-1.jpg http://i123.photobucket.com/albums/o.../FrogJuice.jpg http://i123.photobucket.com/albums/o...lativesize.jpg That is impressive. And you can increase the detail? Amazing. My wife would love it. .......... now ...... will I show her or not? ........... : ) A question; I have no idea what size the coin in the last photo would be, - could you post the diameter as a reference? diggerop It is a quarter. 0.94" or 23.88 mm if you're so inclined. *S* I haven't worked it out in microcubits because my calculator ran out of yak oil....and without yak oil, my yak won't work the treadmill. I just sold a couple of desk name plates to be carved out of soapstone for two executives. (I didn't really want to do this for those pompous *******s, but when I said the price, they said..ohh..okay.) Good on yer. : ) ....and thank you [ two! two! two! ...] If you think this might be fun, you might be interested in http://www.iedu.com/DeSoto/Projects/JBot/ [ three! three! three! ...] Heh. I keep going back looking at your bot. It fascinates me. However, I won't try to build one. Too many projects on the go now and too little time. (How come I then spend so much time writing drivel and posting it on the wreck.? A recently aqquired medical condition, that requires me to be seated for treatment at 4/5 hours every day - temporarily, I hope.) I thought about buying a mini version, but it would really be just another toy for me to play with. Got far too many of them as it is. If I could think of a reason to use it commercially, perhaps providing employment for somebody, I'd go for the idea. Brilliant machines. diggerop |
#49
Posted to rec.woodworking
|
|||
|
|||
Some results of experimenting with soap stone. (Prelude to carving details in wood.)
Rob,
You bags came to the store instead of being drop shipped. I cannot remember your last name or company name to contact you (DOH!). Please call the store. David. "Robatoy" wrote in message ... 3HP spindle on a 1/16" ball nose bit. 2"/second feed rate. That gets kind of hairy as soapstone can have some hard veins in it. The goal of this experiment was to get acceptable detail at fast cutting/feed rates. Detail can be increased by smaller step-over rates. I'm reasonably satisfied. After cutting, I coated the stone with FrogJuice. A clear coating out of a rattle can. http://s123.photobucket.com/albums/o...hthousecnc.flv http://i123.photobucket.com/albums/o...y/Detail-1.jpg http://i123.photobucket.com/albums/o.../FrogJuice.jpg http://i123.photobucket.com/albums/o...lativesize.jpg |
#50
Posted to rec.woodworking
|
|||
|
|||
Some results of experimenting with soap stone. (Prelude to carving details in wood.)
In article ,
"David F. Eisan" wrote: Rob, You bags came to the store instead of being drop shipped. I cannot remember your last name or company name to contact you (DOH!). Please call the store. David. "Robatoy" wrote in message ... 3HP spindle on a 1/16" ball nose bit. 2"/second feed rate. That gets kind of hairy as soapstone can have some hard veins in it. The goal of this experiment was to get acceptable detail at fast cutting/feed rates. Detail can be increased by smaller step-over rates. I'm reasonably satisfied. After cutting, I coated the stone with FrogJuice. A clear coating out of a rattle can. http://s123.photobucket.com/albums/o...urrent=Lightho usecnc.flv http://i123.photobucket.com/albums/o...y/Detail-1.jpg http://i123.photobucket.com/albums/o.../FrogJuice.jpg http://i123.photobucket.com/albums/o...lativesize.jpg We entered those into inventory last month. Besides, if we hadn't had them by now, either you or the fine people at Fein would have heard by now LOL But if they're 'extra'...well then.. |
Reply |
|
Thread Tools | Search this Thread |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Forum | |||
Wood dyes: Experimenting tomorrow | Woodworking | |||
Soap treatment for Geen wood | Woodturning | |||
Wood Magazine Updates Glue Test Results | Woodworking | |||
soap treating of wood | Woodturning | |||
use soap or boil green wood | Woodturning |