I am looking for some help for the Craftsman 10" Table Saw that I
inherited from my Dad. I remember him buying it used in the early
70's, so my guess is that it is a late 60's early 70's model. I have
looked all over it in search of a part number in hopes of fixing it up
a little but the only thing that I can find is the word "Emerson" and
a part number that no one recognizes on the bottom of the insert. The
insert has a little lever that you lift to install and remove the
insert. The Saw is belt driven, with the motor hanging out back of
the saw, and a V-belt running to a pulley driving the blade. The Tilt
adjust is on the left, the height adjust in on the front, and the
adjustments are made with 4" or so plastic knobs with plastic
handles. There is a angle scale on the front with a metal indicator.
The Top is cast iron and it has one open grid cast iron wing. The
fence is a "T" type with a lever that you push down to lock it in
place, the fence also has a knob for "fine adjustments" that is
spring loaded and engages a track under the metal rail that is
attached to the front of the saw and the wing. There is a nice big
"Craftsman" logo on the front. There are no markings on the motor,
but it is wired for 110V. The on/off switch is mounted under the
table just to the right of the blade on the front of the saw. It is a
grey rocker switch with no "safety key". The saw body looks like bent
sheet metal and is painted black. It has a leg set attached that is
made similar to the body of the saw.

With that said, There are several things that I would like to fix on
the saw if I could. The angle and elevation controls have about a 1-2
turn "slop" in them before they engage to move the blade, and the
"lock down" bolt that is on the front seems to have no effect. What
is needed to fix these? It also sounds like some bearings may be
going, is there a good place to get information on how to replace
those?

Thanks.

Mike

"Goose" wrote in message
...
I am looking for some help for the Craftsman 10" Table Saw that I
inherited from my Dad. I remember him buying it used in the early
70's, so my guess is that it is a late 60's early 70's model. I have
looked all over it in search of a part number in hopes of fixing it up
a little but the only thing that I can find is the word "Emerson" and
a part number that no one recognizes on the bottom of the insert. The
insert has a little lever that you lift to install and remove the
insert. The Saw is belt driven, with the motor hanging out back of
the saw, and a V-belt running to a pulley driving the blade. The Tilt
adjust is on the left, the height adjust in on the front, and the
adjustments are made with 4" or so plastic knobs with plastic
handles. There is a angle scale on the front with a metal indicator.
The Top is cast iron and it has one open grid cast iron wing. The
fence is a "T" type with a lever that you push down to lock it in
place, the fence also has a knob for "fine adjustments" that is
spring loaded and engages a track under the metal rail that is
attached to the front of the saw and the wing. There is a nice big
"Craftsman" logo on the front. There are no markings on the motor,
but it is wired for 110V. The on/off switch is mounted under the
table just to the right of the blade on the front of the saw. It is a
grey rocker switch with no "safety key". The saw body looks like bent
sheet metal and is painted black. It has a leg set attached that is
made similar to the body of the saw.

With that said, There are several things that I would like to fix on
the saw if I could. The angle and elevation controls have about a 1-2
turn "slop" in them before they engage to move the blade, and the
"lock down" bolt that is on the front seems to have no effect. What
is needed to fix these? It also sounds like some bearings may be
going, is there a good place to get information on how to replace
those?

Thanks.

Mike
The saw was manufactured by Emerson Electric. The motor might be a 1 hp
unit. Motors have gotten more powerful over the years.
Your saw sounds a lot like mine, but mine is much older as it has a
repulsion-induction motor (Emerson discontinued this type of motor in 1953).
Your motor may be capacitor start induction run.

As far as I know, parts for the angle and elevation controls are no longer
available, and they haven't been for quite some time.

Replacing the bearings is rather easy. You need to remove the arbor, and
then remove the bearings. Then you go to an electric repair shop or an
automotive parts store for replacement.
After putting grease on the bearings, you insert them back in the housing,
insert the arbor, and tighten the nuts which hold everything together.

Jim

Goose wrote:
I am looking for some help for the Craftsman 10" Table Saw that I
inherited from my Dad. I remember him buying it used in the early
70's, so my guess is that it is a late 60's early 70's model. I have
looked all over it in search of a part number in hopes of fixing it up
a little but the only thing that I can find is the word "Emerson" and
a part number that no one recognizes on the bottom of the insert. The
insert has a little lever that you lift to install and remove the
insert. The Saw is belt driven, with the motor hanging out back of
the saw, and a V-belt running to a pulley driving the blade. The Tilt
adjust is on the left, the height adjust in on the front, and the
adjustments are made with 4" or so plastic knobs with plastic
handles. There is a angle scale on the front with a metal indicator.
The Top is cast iron and it has one open grid cast iron wing. The
fence is a "T" type with a lever that you push down to lock it in
place, the fence also has a knob for "fine adjustments" that is
spring loaded and engages a track under the metal rail that is
attached to the front of the saw and the wing. There is a nice big
"Craftsman" logo on the front. There are no markings on the motor,
but it is wired for 110V. The on/off switch is mounted under the
table just to the right of the blade on the front of the saw. It is a
grey rocker switch with no "safety key". The saw body looks like bent
sheet metal and is painted black. It has a leg set attached that is
made similar to the body of the saw.

With that said, There are several things that I would like to fix on
the saw if I could. The angle and elevation controls have about a 1-2
turn "slop" in them before they engage to move the blade, and the
"lock down" bolt that is on the front seems to have no effect. What
is needed to fix these? It also sounds like some bearings may be
going, is there a good place to get information on how to replace
those?

Thanks.

Mike

I also inherited my my father-in-law's Sears table saw. He bought the
saw in about 1969. From the description it sounds the same as mine.

I have always assumed that the adjustment wheels were made from aluminum
not plastic. As for the gages on the saw, I never use them. To square
the blade I use a solid square triangle or a protractor if other angles
are required.

With the design of the saw I have to periodically take a wire brush to
the adjustment screws and the locking bolt to get the sawdust and grim
from the threads. It sounds like the set screw in the adjustment wheels
are loose or the shafts badly scored from being loose. If so this
should be an easy fix.

Fortunately my father was a saver, so I have the original paperwork from
the saw. It has all of the part numbers, etc. I can make a copy,
(which I should have done years ago as the paper is wearing out) and
send you a copy of you would like. It will be a big file. Once copied
the file would be at least 2 to 3 mb and will be in the PDF format.

As for Sears having the parts, you may be surprised.

Additionally you may wish to check the following site.

http://www.owwm.com/

If you would like the file please use email not the newsgroup.

Dang,

I've got one of those, or its cousin.

Dad gave it to me when I bought my first house, a fixer upper.

It still works great, has the slop you mentioned, and cuts wood real
good.

I replaced the fence with a t-square type fence because it would
always move when I locked it.

Also replaced the belt with a link type belt, with a great improvement
in vibration.

Enjoy.

Old guy.

On Sep 22, 2:42*pm, Goose wrote:
I am looking for some help for the Craftsman 10" Table Saw that I
inherited from my Dad. *I remember him buying it used in the early
70's, so my guess is that it is a late 60's early 70's model. *I have
looked all over it in search of a part number in hopes of fixing it up
a little but the only thing that I can find is the word "Emerson" and
a part number that no one recognizes on the bottom of the insert. *The
insert has a little lever that you lift to install and remove the
insert. *The Saw is belt driven, with the motor hanging out back of
the saw, and a V-belt running to a pulley driving the blade. *The Tilt
adjust is on the left, the height adjust in on the front, and the
adjustments are made with 4" or so plastic knobs with plastic
handles. *There is a angle scale on the front with a metal indicator.
The Top is cast iron and it has one open grid cast iron wing. *The
fence is a "T" type with a lever that you push down to lock it in
place, the fence also has a knob for "fine *adjustments" that is
spring loaded and engages a track under the metal rail that is
attached to the front of the saw and the wing. *There is a nice big
"Craftsman" logo on the front. *There are no markings on the motor,
but it is wired for 110V. *The on/off switch is mounted under the
table just to the right of the blade on the front of the saw. *It is a
grey rocker switch with no "safety key". *The saw body looks like bent
sheet metal and is painted black. *It has a leg set attached that is
made similar to the body of the saw.

With that said, There are several things that I would like to fix on
the saw if I could. *The angle and elevation controls have about a 1-2
turn "slop" in them before they engage to move the blade, and the
"lock down" bolt that is on the front seems to have no effect. *What
is needed to fix these? *It also sounds like some bearings may be
going, is there a good place to get information on how to replace
those?

Thanks.

Mike

Old Guy?

Wow, that's what my kids call me, at least my grandkid is too young to
know better.

Fortunately the fence seems to hold well, the miter seems pretty true,
I just need to adjust the blade so that it is parallel to the miter
slot, the back of the blade is farther from the fence than the
front.

Well, in the continuing saga the power switch died. would anyone have
a newer style pull-on-push-off that they would sell? I missed a
couple on epay.

Thanks for the help, y'all

Mike

On Sep 22, 7:30*pm, Old Guy wrote:
Dang,

I've got one of those, or its cousin.

Dad gave it to me when I bought my first house, a fixer upper.

It still works great, has the slop you mentioned, and cuts wood real
good.

I replaced the fence with a t-square type fence because it *would
always move when I locked it.

Also replaced the belt with a link type belt, with a great improvement
in vibration.

Enjoy.

Old guy.

On Sep 22, 2:42*pm, Goose wrote:



I am looking for some help for the Craftsman 10" Table Saw that I
inherited from my Dad. *I remember him buying it used in the early
70's, so my guess is that it is a late 60's early 70's model. *I have
looked all over it in search of a part number in hopes of fixing it up
a little but the only thing that I can find is the word "Emerson" and
a part number that no one recognizes on the bottom of the insert. *The
insert has a little lever that you lift to install and remove the
insert. *The Saw is belt driven, with the motor hanging out back of
the saw, and a V-belt running to a pulley driving the blade. *The Tilt
adjust is on the left, the height adjust in on the front, and the
adjustments are made with 4" or so plastic knobs with plastic
handles. *There is a angle scale on the front with a metal indicator.
The Top is cast iron and it has one open grid cast iron wing. *The
fence is a "T" type with a lever that you push down to lock it in
place, the fence also has a knob for "fine *adjustments" that is
spring loaded and engages a track under the metal rail that is
attached to the front of the saw and the wing. *There is a nice big
"Craftsman" logo on the front. *There are no markings on the motor,
but it is wired for 110V. *The on/off switch is mounted under the
table just to the right of the blade on the front of the saw. *It is a
grey rocker switch with no "safety key". *The saw body looks like bent
sheet metal and is painted black. *It has a leg set attached that is
made similar to the body of the saw.

With that said, There are several things that I would like to fix on
the saw if I could. *The angle and elevation controls have about a 1-2
turn "slop" in them before they engage to move the blade, and the
"lock down" bolt that is on the front seems to have no effect. *What
is needed to fix these? *It also sounds like some bearings may be
going, is there a good place to get information on how to replace
those?

Thanks.

Mike- Hide quoted text -

- Show quoted text -

On Mon, 22 Sep 2008 19:48:00 -0700, Goose wrote:

Fortunately the fence seems to hold well, the miter seems pretty true,
I just need to adjust the blade so that it is parallel to the miter
slot, the back of the blade is farther from the fence than the
front.

If it's set up like other contractor saws, take a look at the PALS system:

http://www.woodcraft.com/family.aspx?familyid=20591

I put one on my saw and it sure made aligning it a lot easier.

Don't forget to check it with the blade at both 90 and 45 degrees. If
it's on for one and off for the other, the rods connecting the two
trunnions are not in the same plane - a real pain to fix as shims seem to
be the only way.

Well, in the continuing saga the power switch died. �would anyone have
a newer style pull-on-push-off that they would sell? �I missed a
couple on epay.

Harbor Freight has generic motor switch. You can also go the starter
and push button route. Takes some time but well worth it.

Bob AZ

Bob, Thanks for the tip,that gives me a couple more ideas to look
into.

While I am asking questions, where could I find a replacement insert
for this saw?

Mike

On Sep 22, 9:19*pm, Bob AZ wrote:
Well, in the continuing saga the power switch died. would anyone have
a newer style pull-on-push-off that they would sell? I missed a
couple on epay.

Harbor Freight has *generic motor switch. You can also go the starter
and push button route. Takes some time but well worth it.

Bob *AZ

"Goose" wrote:

While I am asking questions, where could I find a replacement insert
for this saw?

Why not make some?

That way, you can have a collection of zero clearance inserts.

Lew

Upscale wrote:
"Lew Hodgett" wrote in message
Why not make some?
That way, you can have a collection of zero clearance inserts.

For those of you reading this thread, I have a question in regard to zero
clearance inserts. The table saw I have is a 35 year old Rockwell Beaver
34050. Cutting the outline of an insert is no problem, but I'm a little
stumped on a workable method to properly raise the insert flush with table
saw top. The metal insert I have has adjustable Allen screws which don't
seem all that workable in a home made wooden zero clearance insert.

How do you raise your insert?

[1] Drill holes for adjusters with a #7 drill bit.
[2] Tap 1/4-20
[3] Use a toothpick to smear a /tiny/ bit of silicone caulk on threads
[4] Insert Allen screw and adjust flush
[5] Allow time for caulk to set

:-)

--
Morris Dovey
DeSoto Solar
DeSoto, Iowa USA
http://www.iedu.com/DeSoto/

Upscale wrote:
"Morris Dovey" wrote in message
How do you raise your insert?
[1] Drill holes for adjusters with a #7 drill bit.
[2] Tap 1/4-20
[3] Use a toothpick to smear a /tiny/ bit of silicone caulk on threads
[4] Insert Allen screw and adjust flush
[5] Allow time for caulk to set

Thanks, good method. All thing being equal, I'm betting something similar
would work with 1/4 dowel.

Probably - but might be a bit more difficult to adjust with dowels. I
kinda like the "all-wood" aspect, tho.

A maple insert with dark walnut or cherry dowels might be pretty. :-)

--
Morris Dovey
DeSoto Solar
DeSoto, Iowa USA
http://www.iedu.com/DeSoto/

"Upscale" wrote:

How do you raise your insert?

Trap it with the fence so blade is at least 1/2" away from fence.

Use 1/4-20 socket head set screws for adjustment.

I make mine from 3 pieces of 1/4 hardboard held together with double
back tape, then sanded flush. No screws req'd.

YMMV

Lew

Upscale wrote:

I wondered about the use of the Allen screws in that regard. With the caulk
set, are they fixed in position or thread height adjustable? I was thinking
that using dowel in their stead, I could make them over-long and file them
off as needed to optimum length.

I've only done this one time, and the insert got lost in a long-past
move. Once I had it the way I wanted it I never tried to re-adjust. I'd
guess that I could've used Allen screws without the caulk.

Try your idea. It sounds workable, and if it doesn't pan out there's
always the Allen screw option. I haven't tapped wood very often, but
doing so hasn't produced problems for me.

Another option is to glue in a threaded brass insert or a Propel nut
(kinda like a T-nut without teeth), which would provide metal threads
for the Allen screws - but that'd be more expensive and take more
screwing [sorry] around.

I'm sure you've seen the brass inserts, and LV carries Propel nuts (I
used 'em for the Allen screws that level the table on my RAS - there's
a peek-a-boo photo at the link below)

--
Morris Dovey
DeSoto Solar
DeSoto, Iowa USA
http://www.iedu.com/DeSoto/Projects/RadialArmSaw/

"Lew Hodgett" wrote in message
Why not make some?
That way, you can have a collection of zero clearance inserts.

For those of you reading this thread, I have a question in regard to zero
clearance inserts. The table saw I have is a 35 year old Rockwell Beaver
34050. Cutting the outline of an insert is no problem, but I'm a little
stumped on a workable method to properly raise the insert flush with table
saw top. The metal insert I have has adjustable Allen screws which don't
seem all that workable in a home made wooden zero clearance insert.

How do you raise your insert?

Thanks.

"Morris Dovey" wrote in message
How do you raise your insert?

[1] Drill holes for adjusters with a #7 drill bit.
[2] Tap 1/4-20
[3] Use a toothpick to smear a /tiny/ bit of silicone caulk on threads
[4] Insert Allen screw and adjust flush
[5] Allow time for caulk to set

Thanks, good method. All thing being equal, I'm betting something similar
would work with 1/4 dowel.

"Morris Dovey" wrote in message
[4] Insert Allen screw and adjust flush
[5] Allow time for caulk to set

Thanks, good method. All thing being equal, I'm betting something
similar
would work with 1/4 dowel.

Probably - but might be a bit more difficult to adjust with dowels. I
kinda like the "all-wood" aspect, tho.

I wondered about the use of the Allen screws in that regard. With the caulk
set, are they fixed in position or thread height adjustable? I was thinking
that using dowel in their stead, I could make them over-long and file them
off as needed to optimum length.

On Tue, 23 Sep 2008 01:36:37 -0500, "Upscale"
wrote:

... I'm a little
stumped on a workable method to properly raise the insert flush with table
saw top. The metal insert I have has adjustable Allen screws which don't
seem all that workable in a home made wooden zero clearance insert.

How do you raise your insert?


Made mine from 1/2" UHMW PE with a dovetailed recess for 1/4"
replaceable inserts. Drilled and tapped holes for #6 setscrews in the
appropriate locations. Would work just as well with a hardwood body. I
frequently drill and tap UNC threads in hardwood and BB plywood.

Tom Veatch
Wichita, KS
USA

On Mon, 22 Sep 2008 12:42:47 -0700 (PDT), Goose
wrote:

I am looking for some help for the Craftsman 10" Table Saw that I
inherited from my Dad. I remember him buying it used in the early
70's, so my guess is that it is a late 60's early 70's model.

The Craftsman table saw of roughly mid '60s to mid '90s are basically
the same design, and probably share inner parts such as trunnions and
arbor assembly throughout the range of dates. The principal
differences from one model to the next were primarily in sheet metal,
fence construction, handles, switches, and other external
paraphernalia, with an ever decreasing cost/quality from earliest to
latest, in order to meet a contemporary final price point.

The previously mentioned http://www.owwm.com website should have at
least one manual for a table saw/craftsman/10", one each which, if you
compare more than one, you'll likely note the common heritage.

There is nothing magic regarding the externals cited in paragraph one
with regards to fit. A crank handle from the '90s should fit just fine
on a saw from the '60s. In fact, generic crank handles from secondary
suppliers have often been cited as replacements/upgrades for older
Sears' saws. Switches are even more so--anything which will interrupt
power to the motor (and is rated for the voltage/current) will work,
and with proper selection will be a much better choice than the OEM
switch.

Others have mentioned things such as PALS, pulleys, belts, and rip
fence. In fact, I've long maintained a page at my website devoted to
upgrading a Craftsman table saw, and you might find it informative.



--
LRod

Master Woodbutcher and seasoned termite

Shamelessly whoring my website since 1999

http://www.woodbutcher.net
http://www.normstools.com

Proud participant of rec.woodworking since February, 1997

email addy de-spam-ified due to 1,000 spams per month.
If you can't figure out how to use it, I probably wouldn't
care to correspond with you anyway.

On Tue, 23 Sep 2008 01:36:37 -0500, Upscale wrote:

For those of you reading this thread, I have a question in regard to zero
clearance inserts. The table saw I have is a 35 year old Rockwell Beaver
34050. Cutting the outline of an insert is no problem, but I'm a little
stumped on a workable method to properly raise the insert flush with table
saw top. The metal insert I have has adjustable Allen screws which don't
seem all that workable in a home made wooden zero clearance insert.

How do you raise your insert?


I took 9/16" cedar (fence pickets) and planed/sanded it to the thickness I
needed (about 1/2"). No raising needed.

"Upscale" wrote in message
...

"Lew Hodgett" wrote in message
Why not make some?
That way, you can have a collection of zero clearance inserts.

For those of you reading this thread, I have a question in regard to zero
clearance inserts. The table saw I have is a 35 year old Rockwell Beaver
34050. Cutting the outline of an insert is no problem, but I'm a little
stumped on a workable method to properly raise the insert flush with table
saw top. The metal insert I have has adjustable Allen screws which don't
seem all that workable in a home made wooden zero clearance insert.

How do you raise your insert?

Thanks.


I cut the insert (MDF) very close to the desired depth and then used tape
layers for a flush fit.....works fine but for my next go around I think I'll
try hot melt glue (should be less fiddle till its just right time), probably
wax or oil the saw side (no stick). A press fit before the glue hardens
should make a easy exact flush edge. Rod

While I am asking questions, where could I find a replacement insert
for this saw?

Mike

Mike

I would go online and find the handbook or manual at the Sears site
and try to order the insert there. If no luck I would make one or try
another brand. My sister does woodwork and has made a few of them from
among other materials such as plastic, masonite and aluminum. irst
make a nice pattern from cardboard or the like. And save the pattern
for next time.

Bob AZ

On Monday, September 22, 2008 2:42:47 PM UTC-5, Goose wrote:
I am looking for some help for the Craftsman 10" Table Saw that I
inherited from my Dad. I remember him buying it used in the early
70's, so my guess is that it is a late 60's early 70's model. I have
looked all over it in search of a part number in hopes of fixing it up
a little but the only thing that I can find is the word "Emerson" and
a part number that no one recognizes on the bottom of the insert. The
insert has a little lever that you lift to install and remove the
insert. The Saw is belt driven, with the motor hanging out back of
the saw, and a V-belt running to a pulley driving the blade. The Tilt
adjust is on the left, the height adjust in on the front, and the
adjustments are made with 4" or so plastic knobs with plastic
handles. There is a angle scale on the front with a metal indicator.
The Top is cast iron and it has one open grid cast iron wing. The
fence is a "T" type with a lever that you push down to lock it in
place, the fence also has a knob for "fine adjustments" that is
spring loaded and engages a track under the metal rail that is
attached to the front of the saw and the wing. There is a nice big
"Craftsman" logo on the front. There are no markings on the motor,
but it is wired for 110V. The on/off switch is mounted under the
table just to the right of the blade on the front of the saw. It is a
grey rocker switch with no "safety key". The saw body looks like bent
sheet metal and is painted black. It has a leg set attached that is
made similar to the body of the saw.

With that said, There are several things that I would like to fix on
the saw if I could. The angle and elevation controls have about a 1-2
turn "slop" in them before they engage to move the blade, and the
"lock down" bolt that is on the front seems to have no effect. What
is needed to fix these? It also sounds like some bearings may be
going, is there a good place to get information on how to replace
those?

Thanks.

Mike

On Monday, September 22, 2008 2:42:47 PM UTC-5, Goose wrote:
I am looking for some help for the Craftsman 10" Table Saw that I
inherited from my Dad. I remember him buying it used in the early
70's, so my guess is that it is a late 60's early 70's model. I have
looked all over it in search of a part number in hopes of fixing it up
a little but the only thing that I can find is the word "Emerson" and
a part number that no one recognizes on the bottom of the insert. The
insert has a little lever that you lift to install and remove the
insert. The Saw is belt driven, with the motor hanging out back of
the saw, and a V-belt running to a pulley driving the blade. The Tilt
adjust is on the left, the height adjust in on the front, and the
adjustments are made with 4" or so plastic knobs with plastic
handles. There is a angle scale on the front with a metal indicator.
The Top is cast iron and it has one open grid cast iron wing. The
fence is a "T" type with a lever that you push down to lock it in
place, the fence also has a knob for "fine adjustments" that is
spring loaded and engages a track under the metal rail that is
attached to the front of the saw and the wing. There is a nice big
"Craftsman" logo on the front. There are no markings on the motor,
but it is wired for 110V. The on/off switch is mounted under the
table just to the right of the blade on the front of the saw. It is a
grey rocker switch with no "safety key". The saw body looks like bent
sheet metal and is painted black. It has a leg set attached that is
made similar to the body of the saw.

With that said, There are several things that I would like to fix on
the saw if I could. The angle and elevation controls have about a 1-2
turn "slop" in them before they engage to move the blade, and the
"lock down" bolt that is on the front seems to have no effect. What
is needed to fix these? It also sounds like some bearings may be
going, is there a good place to get information on how to replace
those?

Thanks.

Mike

On Monday, September 22, 2008 2:42:47 PM UTC-5, Goose wrote:
I am looking for some help for the Craftsman 10" Table Saw that I
inherited from my Dad. I remember him buying it used in the early
70's, so my guess is that it is a late 60's early 70's model. I have
looked all over it in search of a part number in hopes of fixing it up
a little but the only thing that I can find is the word "Emerson" and
a part number that no one recognizes on the bottom of the insert. The
insert has a little lever that you lift to install and remove the
insert. The Saw is belt driven, with the motor hanging out back of
the saw, and a V-belt running to a pulley driving the blade. The Tilt
adjust is on the left, the height adjust in on the front, and the
adjustments are made with 4" or so plastic knobs with plastic
handles. There is a angle scale on the front with a metal indicator.
The Top is cast iron and it has one open grid cast iron wing. The
fence is a "T" type with a lever that you push down to lock it in
place, the fence also has a knob for "fine adjustments" that is
spring loaded and engages a track under the metal rail that is
attached to the front of the saw and the wing. There is a nice big
"Craftsman" logo on the front. There are no markings on the motor,
but it is wired for 110V. The on/off switch is mounted under the
table just to the right of the blade on the front of the saw. It is a
grey rocker switch with no "safety key". The saw body looks like bent
sheet metal and is painted black. It has a leg set attached that is
made similar to the body of the saw.

With that said, There are several things that I would like to fix on
the saw if I could. The angle and elevation controls have about a 1-2
turn "slop" in them before they engage to move the blade, and the
"lock down" bolt that is on the front seems to have no effect. What
is needed to fix these? It also sounds like some bearings may be
going, is there a good place to get information on how to replace
those?

Thanks.

Mike

On Monday, September 22, 2008 2:42:47 PM UTC-5, Goose wrote:
I am looking for some help for the Craftsman 10" Table Saw that I
inherited from my Dad. I remember him buying it used in the early
70's, so my guess is that it is a late 60's early 70's model. I have
looked all over it in search of a part number in hopes of fixing it up
a little but the only thing that I can find is the word "Emerson" and
a part number that no one recognizes on the bottom of the insert. The
insert has a little lever that you lift to install and remove the
insert. The Saw is belt driven, with the motor hanging out back of
the saw, and a V-belt running to a pulley driving the blade. The Tilt
adjust is on the left, the height adjust in on the front, and the
adjustments are made with 4" or so plastic knobs with plastic
handles. There is a angle scale on the front with a metal indicator.
The Top is cast iron and it has one open grid cast iron wing. The
fence is a "T" type with a lever that you push down to lock it in
place, the fence also has a knob for "fine adjustments" that is
spring loaded and engages a track under the metal rail that is
attached to the front of the saw and the wing. There is a nice big
"Craftsman" logo on the front. There are no markings on the motor,
but it is wired for 110V. The on/off switch is mounted under the
table just to the right of the blade on the front of the saw. It is a
grey rocker switch with no "safety key". The saw body looks like bent
sheet metal and is painted black. It has a leg set attached that is
made similar to the body of the saw.

With that said, There are several things that I would like to fix on
the saw if I could. The angle and elevation controls have about a 1-2
turn "slop" in them before they engage to move the blade, and the
"lock down" bolt that is on the front seems to have no effect. What
is needed to fix these? It also sounds like some bearings may be
going, is there a good place to get information on how to replace
those?

Thanks.

Mike

wrote:
On Monday, September 22, 2008 2:42:47 PM UTC-5, Goose wrote:
I am looking for some help for the Craftsman 10" Table Saw that I
inherited from my Dad. I remember him buying it used in the early
70's, so my guess is that it is a late 60's early 70's model. I have
looked all over it in search of a part number in hopes of fixing it
up a little but the only thing that I can find is the word "Emerson"
and a part number that no one recognizes on the bottom of the
insert. The insert has a little lever that you lift to install and
remove the insert. The Saw is belt driven, with the motor hanging
out back of the saw, and a V-belt running to a pulley driving the
blade. The Tilt adjust is on the left, the height adjust in on the
front, and the adjustments are made with 4" or so plastic knobs with
plastic handles. There is a angle scale on the front with a metal
indicator. The Top is cast iron and it has one open grid cast iron
wing. The fence is a "T" type with a lever that you push down to
lock it in place, the fence also has a knob for "fine adjustments"
that is spring loaded and engages a track under the metal rail that
is attached to the front of the saw and the wing. There is a nice
big "Craftsman" logo on the front. There are no markings on the
motor, but it is wired for 110V. The on/off switch is mounted under
the table just to the right of the blade on the front of the saw.
It is a grey rocker switch with no "safety key". The saw body looks
like bent sheet metal and is painted black. It has a leg set
attached that is made similar to the body of the saw.

With that said, There are several things that I would like to fix on
the saw if I could. The angle and elevation controls have about a
1-2 turn "slop" in them before they engage to move the blade, and the
"lock down" bolt that is on the front seems to have no effect. What
is needed to fix these? It also sounds like some bearings may be
going, is there a good place to get information on how to replace
those?

Thanks.

Mike

Ok - I have seen 4 posts of this same message, so I get it that you would
like some help. I own a Craftsman Model 100 that sounds to be very
similar - or exactly like your saw. It's a very good saw. I have tuned
mine to very precise limits and find it to be extremely reliable. Recently
replaced the arbor bearings and it just sings like a virgin now. I would be
happy to work you through some steps - and there will be multiple steps, so
you can choose to conduct this via the newsgroup, or you may feel free to
contact me via my (pay attention to the word REMOVE) email address in my
sig.

Look forward to making your saw into a very reliable, very good piece of
machinery.

--

-Mike-

On 12/12/2013 12:47 PM, Mike Marlow wrote:
I am looking for some help for the Craftsman 10" Table Saw that I
inherited from my Dad. I remember him buying it used in the early
70's, so my guess is that it is a late 60's early 70's model. I have
looked all over it in search of a part number in hopes of fixing it
up a little but the only thing that I can find is the word "Emerson"
and a part number that no one recognizes on the bottom of the
insert. The insert has a little lever that you lift to install and
remove the insert.


The insert may not be part of the original saw so the name may be
meaningless. I know mine was purchased about 20 years after the saw.

I have the original manual for the Sears 10" table saw (113.29903) and
the motor (113.12170) that came with the saw, that was purchased in 1970
by my father in law.

My saw has two aluminum wings to extend the working surface.

I have sent a direct email with some pictures of the saw, one has
Craftsman part number.

This is a little early with a similar part number
http://vintagemachinery.org/photoind....aspx?id=16750

The difference may be the motor that the saw was packaged with.

This is a very good saw that I use routinely to make picture frames and
stretchers for my wife (acyclic on canvas) There are very few saws that
will have its quality today.

In article ,
Keith Nuttle wrote:

On 12/12/2013 12:47 PM, Mike Marlow wrote:
I am looking for some help for the Craftsman 10" Table Saw that I
inherited from my Dad. I remember him buying it used in the early
70's, so my guess is that it is a late 60's early 70's model. I have
looked all over it in search of a part number in hopes of fixing it
up a little but the only thing that I can find is the word "Emerson"
and a part number that no one recognizes on the bottom of the
insert. The insert has a little lever that you lift to install and
remove the insert.


The insert may not be part of the original saw so the name may be
meaningless. I know mine was purchased about 20 years after the saw.

I have the original manual for the Sears 10" table saw (113.29903) and
the motor (113.12170) that came with the saw, that was purchased in 1970
by my father in law.

My saw has two aluminum wings to extend the working surface.

I have sent a direct email with some pictures of the saw, one has
Craftsman part number.

This is a little early with a similar part number
http://vintagemachinery.org/photoind....aspx?id=16750

The difference may be the motor that the saw was packaged with.

This is a very good saw that I use routinely to make picture frames and
stretchers for my wife (acyclic on canvas) There are very few saws that
will have its quality today.

Yes it would be nice to have a manual. However, unless there is some
unique part broken, in which case it would not be economical to repair,
generic parts such as bearings, belts, and motors are readily available
on the open market.

Emerson did make radial arm saws[ras] for Sears. I don't know if they
made their table saws. There is a current "recall" on some of their
ras. The replacement parts were shipped from emerson. Perhaps some one
here can remember the contact number or search the archives of this NG
or reccrafts metalworking. Then call that # and see what they can tell
you.

I have a Sears table saw of about that vintage. The model number is:

113.29992

CP

Pilgrim wrote:

Emerson did make radial arm saws[ras] for Sears. I don't know if they
made their table saws.

Yes, they did and any google search of the Sears model number will quckly
revearl that.


There is a current "recall" on some of their
ras.

Yes - buy completely irrelevant. The OP is talking about a table saw.


I have a Sears table saw of about that vintage. The model number is:


So - why didn't you talk about that instead of your RAS?

--

-Mike-