Home |
Search |
Today's Posts |
|
Woodworking (rec.woodworking) Discussion forum covering all aspects of working with wood. All levels of expertise are encouraged to particiapte. |
Reply |
|
LinkBack | Thread Tools | Display Modes |
#1
|
|||
|
|||
New old bandsaw 220v or 110?
I just got at an auction a Biro model 34 bandsaw for $135 and now that I
have cleaned it up a little I am not positive if it is set up to run on 220v. I think it is because the plug has one blade vertical and the other horizontal in other words ( - ! like this). The ground pin is in the normal position. Can anyone tell me an easy way to tell if I am correct? I don't want to just plug it in and see what happens. After all I would hate to burn the sucker up after almost giving myself a hernia picking this 400-500 pound monster up and getting it home. As always thanks for the help. Larry -- larry in Cinci |
#2
|
|||
|
|||
sounds like my 220 plug
len |
#3
|
|||
|
|||
In article , "larry's lair" wrote:
I just got at an auction a Biro model 34 bandsaw for $135 and now that I have cleaned it up a little I am not positive if it is set up to run on 220v. I think it is because the plug has one blade vertical and the other horizontal in other words ( - ! like this). The ground pin is in the normal position. Can anyone tell me an easy way to tell if I am correct? I don't want to just plug it in and see what happens. After all I would hate to burn the sucker up after almost giving myself a hernia picking this 400-500 pound monster up and getting it home. As always thanks for the help. Larry Have a look here http://www.passandseymour.com/pdf/T008.pdf to see exactly what you have. Pay attention to the difference between plug and receptacle configurations. Plug like this | -- o is 120V 20A. Plug like *this* -- | o is 240V 20A. Also be aware that the plug configuration does not necessarily indicate what the motor actually needs -- it's *supposed* to match, but on used equipment, somebody might have changed it incorrectly, and you don't have any way of knowing that it really *does* match unless you check the motor wiring. There's probably a diagram on the motor, or a label, that would indicate what it is. -- Regards, Doug Miller (alphageek at milmac dot com) It's time to throw all their damned tea in the harbor again. |
#4
|
|||
|
|||
Well, its a 20a plug, and 20a at 240v seems excessive, so it is probably
120v. But, just to be sure http://www.networkcable.com/pages/co...onlocking.html You can't really make a mistake because a 120v plug won't fit a 240v outlet. |
#5
|
|||
|
|||
In article , "toller" wrote:
Well, its a 20a plug, and 20a at 240v seems excessive, so it is probably 120v. But, just to be sure http://www.networkcable.com/pages/co...onlocking.html You can't really make a mistake because a 120v plug won't fit a 240v outlet. Except that, with used equipment, you have no idea what sort of jackleg modifications may have been made by a prior owner. -- Regards, Doug Miller (alphageek at milmac dot com) It's time to throw all their damned tea in the harbor again. |
#7
|
|||
|
|||
"larry's lair" wrote in message ... I just got at an auction a Biro model 34 bandsaw for $135 and now that I have cleaned it up a little I am not positive if it is set up to run on 220v. I think it is because the plug has one blade vertical and the other horizontal in other words ( - ! like this). The ground pin is in the normal position. Can anyone tell me an easy way to tell if I am correct? I don't want to just plug it in and see what happens. After all I would hate to burn the sucker up after almost giving myself a hernia picking this 400-500 pound monster up and getting it home. As always thanks for the help. Larry -- larry in Cinci Look at the motor plate. It should give the wiring diagram for 120 and 240 service. Then look at the wiring on the motor to see which way it is connected. The field windings are connected in series for 240 and in parallel for 120. Jim |
Reply |
Thread Tools | Search this Thread |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Forum | |||
Craftex Bandsaw | Woodworking | |||
7.5hp 3 phase, 440v to 220v. Am I wiring this up right? | Metalworking | |||
HELP! Need question answered on 220v microwave | Home Repair | |||
Maloof: “Then I just cut ________ on the bandsaw | Woodworking | |||
Bandsaw Box... | Woodworking |