Home |
Search |
Today's Posts |
|
Woodworking Plans and Photos (alt.binaries.pictures.woodworking) - Show off or just share photos of your hard work. |
Reply |
|
LinkBack | Thread Tools | Display Modes |
#1
Posted to alt.binaries.pictures.woodworking
|
|||
|
|||
Today's project - ash.jpg (1/1)
|
#2
Posted to alt.binaries.pictures.woodworking
|
|||
|
|||
Today's project - ash.jpg (1/1)
"mac davis" wrote in message ... Nice. Just curious, do you turn that "really slow" on the outside in case of the unthinkable? Bill |
#3
Posted to alt.binaries.pictures.woodworking
|
|||
|
|||
Today's project - ash.jpg (1/1)
That's quite an ash-crack you've got there.
B. |
#4
Posted to alt.binaries.pictures.woodworking
|
|||
|
|||
Today's project - ash.jpg (1/1)
On Mon, 12 Oct 2009 17:59:33 -0400, "Bill" wrote:
"mac davis" wrote in message .. . Nice. Just curious, do you turn that "really slow" on the outside in case of the unthinkable? Bill I think I started at about 460 rpm, because it had some vibration at 500. (default start speed) After the top and bottom were rounded, I went up to about 800 rpm to take what was left of the corners off... Ran out of time this morning, hoping to finish it tomorrow.. mac Please remove splinters before emailing |
#5
Posted to alt.binaries.pictures.woodworking
|
|||
|
|||
Today's project - ash.jpg (1/1)
On Mon, 12 Oct 2009 19:50:02 -0400, "Buddy Matlosz"
wrote: find a knead and fill it? That's quite an ash-crack you've got there. B. "mac davis" wrote in message .. . mac Please remove splinters before emailing |
#6
Posted to alt.binaries.pictures.woodworking
|
|||
|
|||
Today's project - ash.jpg (1/1)
On Mon, 12 Oct 2009 23:39:05 -0700, mac davis
wrote: On Mon, 12 Oct 2009 19:50:02 -0400, "Buddy Matlosz" wrote: find a knead and fill it? That's quite an ash-crack you've got there. B. "mac davis" wrote in message . .. mac Please remove splinters before emailing Is it hard to find a good piece of ash where you are Mac? I've had to go a couple towns over to find a good piece sometimes myself! =0) Lenny |
#7
Posted to alt.binaries.pictures.woodworking
|
|||
|
|||
Today's project - ash.jpg (1/1)
"mac davis" wrote in message ... On Mon, 12 Oct 2009 17:59:33 -0400, "Bill" wrote: "mac davis" wrote in message . .. Nice. Just curious, do you turn that "really slow" on the outside in case of the unthinkable? Bill I think I started at about 460 rpm, because it had some vibration at 500. (default start speed) After the top and bottom were rounded, I went up to about 800 rpm to take what was left of the corners off... Ran out of time this morning, hoping to finish it tomorrow.. mac Please remove splinters before emailing Thank you for your reply. That's quite a piece of wood. I will be eager to see how you transform it. Bill |
#8
Posted to alt.binaries.pictures.woodworking
|
|||
|
|||
Today's project - ash.jpg (1/1)
|
#9
Posted to alt.binaries.pictures.woodworking
|
|||
|
|||
Today's project - ash.jpg (1/1)
On Wed, 14 Oct 2009 00:30:50 -0400, "Bill" wrote:
Thank you for your reply. That's quite a piece of wood. I will be eager to see how you transform it. Bill Always happy to confuse fellow turner's, Bill... I meant to take an "in progress" picture this afternoon and forgot.. It's roughed, shaped, hollowed and undercut.. I'll take a pic before I finish turn and sand.. mac Please remove splinters before emailing |
Reply |
Thread Tools | Search this Thread |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Forum | |||
Today's project - ash.jpg (0/1) | Woodworking Plans and Photos | |||
Today's pet peeve | Home Ownership | |||
today's weird ad | Home Repair | |||
Today's top tips | UK diy | |||
Today's thought | Woodworking |