Today's project - ash.jpg (1/1)
 

Today's project - ash.jpg (1/1)
 

"mac davis" wrote in message
...

Nice. Just curious, do you turn that "really slow" on the outside in case
of the unthinkable?

Bill

Today's project - ash.jpg (1/1)
 

That's quite an ash-crack you've got there.

B.

Today's project - ash.jpg (1/1)
 

On Mon, 12 Oct 2009 17:59:33 -0400, "Bill" wrote:


"mac davis" wrote in message
.. .

Nice. Just curious, do you turn that "really slow" on the outside in case
of the unthinkable?

Bill

I think I started at about 460 rpm, because it had some vibration at 500.
(default start speed)

After the top and bottom were rounded, I went up to about 800 rpm to take what
was left of the corners off...

Ran out of time this morning, hoping to finish it tomorrow..


mac

Please remove splinters before emailing

Today's project - ash.jpg (1/1)
 

On Mon, 12 Oct 2009 19:50:02 -0400, "Buddy Matlosz"
wrote:

find a knead and fill it?

That's quite an ash-crack you've got there.

B.

"mac davis" wrote in message
.. .


mac

Please remove splinters before emailing

Today's project - ash.jpg (1/1)
 

On Mon, 12 Oct 2009 23:39:05 -0700, mac davis
wrote:

On Mon, 12 Oct 2009 19:50:02 -0400, "Buddy Matlosz"
wrote:

find a knead and fill it?

That's quite an ash-crack you've got there.

B.

"mac davis" wrote in message
. ..


mac

Please remove splinters before emailing
Is it hard to find a good piece of ash where you are Mac?
I've had to go a couple towns over to find a good piece sometimes
myself!

=0)
Lenny

Today's project - ash.jpg (1/1)
 

"mac davis" wrote in message
...
On Mon, 12 Oct 2009 17:59:33 -0400, "Bill"
wrote:


"mac davis" wrote in message
. ..

Nice. Just curious, do you turn that "really slow" on the outside in case
of the unthinkable?

Bill

I think I started at about 460 rpm, because it had some vibration at 500.
(default start speed)

After the top and bottom were rounded, I went up to about 800 rpm to take
what
was left of the corners off...

Ran out of time this morning, hoping to finish it tomorrow..


mac

Please remove splinters before emailing


Thank you for your reply. That's quite a piece of wood. I will be eager to
see how you
transform it.

Bill

Today's project - ash.jpg (1/1)
 

On Tue, 13 Oct 2009 19:22:53 -0400, wrote:

Is it hard to find a good piece of ash where you are Mac?
I've had to go a couple towns over to find a good piece sometimes
myself!

=0)
Lenny

Well, I guess you'd say so.. I live in Mexico and this log was sent by a friend
in Upstate new York.. lol

Lots of ironwood here, but not much else that turns well...


mac

Please remove splinters before emailing

Today's project - ash.jpg (1/1)
 

On Wed, 14 Oct 2009 00:30:50 -0400, "Bill" wrote:


Thank you for your reply. That's quite a piece of wood. I will be eager to
see how you
transform it.

Bill

Always happy to confuse fellow turner's, Bill...

I meant to take an "in progress" picture this afternoon and forgot..
It's roughed, shaped, hollowed and undercut.. I'll take a pic before I finish
turn and sand..


mac

Please remove splinters before emailing