Woodworking Plans and Photos (alt.binaries.pictures.woodworking) - Show off or just share photos of your hard work.

Reply
 
LinkBack Thread Tools Search this Thread Display Modes
  #1   Report Post  
Posted to alt.binaries.pictures.woodworking
external usenet poster
 
Posts: 130
Default Basics of kitchen counter

I'm not a woodworker, but I am basically handy. In my apartment there is a
5 inch gap between my sink cabinet and the range. I want to make a filler
with 1x6 covered with shelving that is pre-laminated with mica.
(Fortunately the scheme is white and that's the color of available shelves.)

Here is a rough diagram of the cross-section as I envision it. The back
needs to overhang a 1.5" bulge in the wall.

Maybe the structure could be improved. I appreciate any input.


--

Reply in group, but if emailing add another
zero, and remove the last word.




Attached Thumbnails
Basics of kitchen counter-counter-top-png  
  #2   Report Post  
Posted to alt.binaries.pictures.woodworking
external usenet poster
 
Posts: 1,185
Default Basics of kitchen counter

Tom Del Rosso wrote:
Here is a rough diagram of the cross-section as I envision it. The back
needs to overhang a 1.5" bulge in the wall.

Maybe the structure could be improved. I appreciate any input.


Would work, but could be simpler.

I'd go with a large top box and a smaller bottom box. Same amount of
work overall, but it gives a bit more support for the front. Probably
no need for the diagonal--just screw the box to the wall and the floor.

Chris
  #3   Report Post  
Posted to alt.binaries.pictures.woodworking
external usenet poster
 
Posts: 130
Default Basics of kitchen counter

"Chris Friesen" wrote in message

Tom Del Rosso wrote:
Here is a rough diagram of the cross-section as I envision it. The
back needs to overhang a 1.5" bulge in the wall.

Maybe the structure could be improved. I appreciate any input.


Would work, but could be simpler.

I'd go with a large top box and a smaller bottom box. Same amount of
work overall, but it gives a bit more support for the front. Probably
no need for the diagonal--just screw the box to the wall and the
floor.


Thanks a lot. The bottom box will be on the other axis then, so it will be
open on top and bottom for stability.

But without moving the range I don't see how I can get access to screw it to
the wall, so the diagonal might be necessary in the top box.


--

Reply in group, but if emailing add another
zero, and remove the last word.


  #4   Report Post  
Posted to alt.binaries.pictures.woodworking
external usenet poster
 
Posts: 1,185
Default Basics of kitchen counter

Tom Del Rosso wrote:

But without moving the range I don't see how I can get access to screw it to
the wall, so the diagonal might be necessary in the top box.


With most ranges it isn't all that hard to pull them out a couple feet.
They're usually just sitting on the floor.

Chris
Reply
Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules

Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
THE BASICS OF KITCHEN CABINET RE-FACING J T Woodworking 0 March 22nd 07 02:01 AM
Kitchen counter height Robert Gammon Home Repair 24 July 9th 06 05:53 PM
Kitchen Counter Question Kim Home Repair 2 March 19th 05 03:54 AM
kitchen counter tops Chuck Lysaght Home Ownership 0 October 13th 04 04:02 AM
Kitchen counter D'Olier Home Repair 4 June 25th 03 03:21 AM


All times are GMT +1. The time now is 09:37 AM.

Powered by vBulletin® Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004-2024 DIYbanter.
The comments are property of their posters.
 

About Us

"It's about DIY & home improvement"