Home |
Search |
Today's Posts |
|
Woodturning (rec.crafts.woodturning) To discuss tools, techniques, styles, materials, shows and competitions, education and educational materials related to woodturning. All skill levels are welcome, from art turners to production turners, beginners to masters. |
Reply |
|
LinkBack | Thread Tools | Display Modes |
#1
Posted to rec.crafts.woodturning
|
|||
|
|||
Oops! 2 J-Line J-170's
I wasn't paying attention and thought I was buying 2 Powermatic 90's for
$200 ea., and wound up with two Brodhead Garrett J-170s for $400 ea. ooch. Anyway, the casting is a lot heavier than my Grizzly G1495, and they have newer 220V motors. I figure I'll sell the new G1495 and one of the J-170's and still have a better lathe than I started with. Anybody with any kind words or horror stories about J-170s? I'm thinking I'll be hard pressed to get 400 bucks for one. -- Timothy Juvenal www.tjwoodworking.com |
#2
Posted to rec.crafts.woodturning
|
|||
|
|||
Oops! 2 J-Line J-170's
Hi Tim
These are 3 phase 220V motors ?? If so, not many people have 3 phase, and either need a convertor or other motor. Nice heavy lathe, get some risers and you're set for some serious turning Have fun and take care Leo Van Der Loo Juvenal wrote: I wasn't paying attention and thought I was buying 2 Powermatic 90's for $200 ea., and wound up with two Brodhead Garrett J-170s for $400 ea. ooch. Anyway, the casting is a lot heavier than my Grizzly G1495, and they have newer 220V motors. I figure I'll sell the new G1495 and one of the J-170's and still have a better lathe than I started with. Anybody with any kind words or horror stories about J-170s? I'm thinking I'll be hard pressed to get 400 bucks for one. -- Timothy Juvenal www.tjwoodworking.com |
#4
Posted to rec.crafts.woodturning
|
|||
|
|||
Oops! 2 J-Line J-170's
Leo Van Der Loo wrote in message... These are 3 phase 220V motors ?? No, single phase. Not sure of the hp. Nice heavy lathe, get some risers and you're set for some serious turning Risers to increase the swing? I think the bed and head are all one casting. I have them in another building, so I'll check them out later today. Here's the manual with a pic of the casting: http://www.owwm.com/files/PDF/YatesA.../J170Lathe.pdf -- Timothy Juvenal www.tjwoodworking.com |
#5
Posted to rec.crafts.woodturning
|
|||
|
|||
Oops! 2 J-Line J-170's
Leo Van Der Loo wrote in message...
get some risers and you're set for some serious turning Leo: Checked out the lathes and you're correct - risers can indeed be added. And as the lathes are next door in my friends machine shop, making some nice looking risers shouldn't be any problem at all. Thanks for the heads up on that, as I will definately want to increase the swing. Unfortunately, I won't be able to work on them till after the holidays, and don't have room in my shop for another lathe until the Griz is sold, which can't happen yet as I have two jobs that require turnings & can't give up my working lathe just yet. Sigh. -- Timothy Juvenal www.tjwoodworking.com |
Reply |
Thread Tools | Search this Thread |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Forum | |||
110v line to 220v line? | Home Repair | |||
In-line vs. off-line chemical feeders | Home Repair | |||
"Grass Gator n'Cut Fixed 4 Line Head" Weed Wacker Replacement For Bump-Line Feed Head ? | Home Repair | |||
Adding a sink drain line into existing 3" PVC drain / waste line | Home Repair |