I've got some trees, pines particularly, that I'd like to slab for an
outbuilding. I understand there's a ripping blade for a chainsaw but have
heard, also, that it's not necessary.

Certainly Mac's sawmill would work better but I haven't got Mac's money .
Any thoughts, warnings, advice, suggestions?

TomNie

Take a look at the Logosol people. They likely know more about chain saw
lumbering than anyone else. The Granberg is also used by some folks with
good success. A web search will easily turn up both.

--
God bless and safe turning
Darrell Feltmate
Truro, NS Canada
www.aroundthewoods.com

"Tom Nie" wrote in message
...
I've got some trees, pines particularly, that I'd like to slab for an
outbuilding. I understand there's a ripping blade for a chainsaw but have
heard, also, that it's not necessary.

Certainly Mac's sawmill would work better but I haven't got Mac's money
. Any thoughts, warnings, advice, suggestions?


You probably heard half wrong. Making up bowl blanks can be done by
employing the bar along the face grain on a short length and doesn't
benefit. Sawing end grain along a long piece benefits from the revised
tooth angle on a rip chain, and that's what most chainsaw mills do.

I guess I'd check woodmizer's site for an owner/operator near me and get it
done that way.

Come to think of it, that's what I do....

George wrote:
"Tom Nie" wrote in message
...

I've got some trees, pines particularly, that I'd like to slab for an
outbuilding. I understand there's a ripping blade for a chainsaw but have
heard, also, that it's not necessary.

Certainly Mac's sawmill would work better but I haven't got Mac's money
. Any thoughts, warnings, advice, suggestions?



You probably heard half wrong. Making up bowl blanks can be done by
employing the bar along the face grain on a short length and doesn't
benefit. Sawing end grain along a long piece benefits from the revised
tooth angle on a rip chain, and that's what most chainsaw mills do.

I guess I'd check woodmizer's site for an owner/operator near me and get it
done that way.

Come to think of it, that's what I do....


Where you need to go is: www.baileys-online.com they have chains,
bars and the like at fair prices. Geo.

Woodmizer has much of the market but there are a number of other good
portable sawmills out there. Timberking and Baker come to mind and
either would be willing, I think, to refer you to an owner.

I think in the end that you will find the money to have someone saw for
you to be a good investment as opposed to trying to do it with a
chainsaw. Also, your yield is going to be much better with a bandmill.

Bill

George wrote:
"Tom Nie" wrote in message
...

I've got some trees, pines particularly, that I'd like to slab for an
outbuilding. I understand there's a ripping blade for a chainsaw but have
heard, also, that it's not necessary.

Certainly Mac's sawmill would work better but I haven't got Mac's money
. Any thoughts, warnings, advice, suggestions?



You probably heard half wrong. Making up bowl blanks can be done by
employing the bar along the face grain on a short length and doesn't
benefit. Sawing end grain along a long piece benefits from the revised
tooth angle on a rip chain, and that's what most chainsaw mills do.

I guess I'd check woodmizer's site for an owner/operator near me and get it
done that way.

Come to think of it, that's what I do....

I've got some trees, pines particularly, that I'd like to slab for an
outbuilding. I understand there's a ripping blade for a chainsaw but have
heard, also, that it's not necessary.

Certainly Mac's sawmill would work better but I haven't got Mac's money .
Any thoughts, warnings, advice, suggestions?

Your post was timely, I was just thinking about this yesterday when I rolled two
18" cottonwood logs under the shed roof to dry. Here are the websites for the
portable sawmills people have replied with. Granberg has the simple, low-tech
devices to convert your chainsaw into a weekend sawmill including ripping
blades. Dan

http://www.baker-online.com/
http://www.granberg.com/
http://www.logosol.com/
http://www.timberking.com/
http://www.woodmizer.com/en/index.aspx

Hi Tom

My take on it, unless you are going to go into a part time job cutting
up logs in your area, I would suggest to have someone come with a
Woodmizer or similar band saw and have it done.
Yes you could saw with a chain saw, there are setups that make it
possible to do that, like the (Alaska mill), you need a big enough
chain saw to handle the chain length required and you should also use a
ripping chain, a very good bar or you saw sideways, keep the chain snug
and sweat G.
Than you have to be able to set up the logs so that you can saw them,
move the sawn slabs etc,.
You will lose a lot more wood using a chain saw and it is a lot slower.
If I had a few logs and was unable to get them to a mill, I would get
someone with a saw to come and cut up the logs.
A friend of mine and I hauled a dozen or so eastern white cedar logs to
a sayer just Oh 14" to 18"D logs mostly 15 to 20 feet long, for
building a bridge over a gully and it took not very long to slice the
logs up into 2" slabs, with the 3 of us, if you have to do that by
yourself it will take a lot longer and it can get risky, logs are heavy
and if you are not used to doing that it's just-- well-- that, risky.

Have fun and take care
Leo Van Der Loo

"Tom Nie" wrote in message
...
I've got some trees, pines particularly, that I'd like to slab for an
outbuilding. I understand there's a ripping blade for a chainsaw but have
heard, also, that it's not necessary.

Certainly Mac's sawmill would work better but I haven't got Mac's money
. Any thoughts, warnings, advice, suggestions?

TomNie
================
Tom,
You might want to check with some of the turner and other wood working clubs
in your area. See if they know any one who has a bandsaw mill that's willing
to works on shares. Some in the TX area will cut for a portion of the wood.
Percentage is negotiable in some cases, depending on travel time, type wood,
etc. YMMV

Ken Moon
Webberville, TX.