Good evening to all.

A dropbox pic he
https://www.dropbox.com/s/djbbkmbz14...0bolt.JPG?dl=0

I'm trying to put an old Wolf TG8B double ended 8 inch bench grinder
back in harness. Something of a challenge as it has been out in the
weather for about 15 years. All is probably Imperial as it was made in
West London 50 or 60 years ago.
The stones rotate, which is encouraging. I have removed the rests with
their rods from the main frame. This with the aid of some heat and a bit
of force. I have to go a bit steady as this old thing is mainly cast
aluminium. Slowly & steadily I will get the rest of it apart

The work rests are secured to steel rods by bolts that I have never seen
the like of.
The headless bolt is 1/2" dia by 2-1/2" long. Possibly a Whitworth
thread (advice on this would be much appreciated).
The bolt has a 'sort of' elongated C cut from it. When slackened this
would allow the work rest to be adjusted left/right and fore/aft. The
bolt I have removed is quite wasted, probably not reusable. I'm still
trying to free the second and may destroy it in the process.
Very possibly these are propriety items and Wolf disappeared to Kango et
al years ago.

Any thoughts please.

Many thanks,

Nick

On 20/06/2020 00:09, Nick wrote:
Good evening to all.

A dropbox pic he
https://www.dropbox.com/s/djbbkmbz14...0bolt.JPG?dl=0

I'm trying to put an old Wolf TG8B double ended 8 inch bench grinder
back in harness. Something of a challenge as it has been out in the
weather for about 15 years. All is probably Imperial as it was made in
West London 50 or 60 years ago.
The stones rotate, which is encouraging. I have removed the rests with
their rods from the main frame. This with the aid of some heat and a bit
of force. I have to go a bit steady as this old thing is mainly cast
aluminium. Slowly & steadily I will get the rest of it apart

The work rests are secured to steel rods by bolts that I have never seen
the like of.
The headless bolt is 1/2" dia by 2-1/2" long. Possibly a Whitworth
thread (advice on this would be much appreciated).

1/2" BSW would be 12 TPI, which looking at the picture is plausible.

The bolt has a 'sort of' elongated C cut from it. When slackened this
would allow the work rest to be adjusted left/right and fore/aft. The
bolt I have removed is quite wasted, probably not reusable. I'm still
trying to free the second and may destroy it in the process.
Very possibly these are propriety items and Wolf disappeared to Kango et
al years ago.

Any thoughts please.

It looks like the kind of thing that would be relatively easy to
fabricate. Find a bolt with the right pitch thread, and a smooth upper
part to the shank. Stick a nut on the end of it, and weld it on. Then
chop off the original hex head, leaving you with the same layout of hex
head, threaded section adjacent to it, and smooth shank beyond. Lastly
shape the required profile with a grinder.


--
Cheers,

John.

/================================================== ===============\
| Internode Ltd - http://www.internode.co.uk |
|-----------------------------------------------------------------|
| John Rumm - john(at)internode(dot)co(dot)uk |
\================================================= ================/

On Sat, 20 Jun 2020 00:09:32 +0100, in uk.d-i-y Nick wrote:

Good evening to all.

A dropbox pic he
https://www.dropbox.com/s/djbbkmbz14...0bolt.JPG?dl=0

I'm trying to put an old Wolf TG8B double ended 8 inch bench grinder
back in harness. Something of a challenge as it has been out in the
weather for about 15 years. All is probably Imperial as it was made in
West London 50 or 60 years ago.
The stones rotate, which is encouraging. I have removed the rests with
their rods from the main frame. This with the aid of some heat and a bit
of force. I have to go a bit steady as this old thing is mainly cast
aluminium. Slowly & steadily I will get the rest of it apart

The work rests are secured to steel rods by bolts that I have never seen
the like of.
The headless bolt is 1/2" dia by 2-1/2" long. Possibly a Whitworth
thread (advice on this would be much appreciated).
The bolt has a 'sort of' elongated C cut from it. When slackened this
would allow the work rest to be adjusted left/right and fore/aft. The
bolt I have removed is quite wasted, probably not reusable. I'm still
trying to free the second and may destroy it in the process.
Very possibly these are propriety items and Wolf disappeared to Kango et
al years ago.

Any thoughts please.

Many thanks,

It's a cotter-pin. They can be found fixing pedal cranks to the bottom-bracket shaft on older bicycles. Yours looks to be severely worn. The "C" shape is supposed to be a flat ground at a slight angle to the axis, the idea being that as it is tightened, the wedge shape jams firmly against a flat ground on the corresponding shaft. Also found securing the kick-start pedal on older motor-cycles, and anywhere a lever needs to be secured perpendicular to a shaft. If you're lucky yours may me a standard cycle size.

https://www.sheldonbrown.com/cotters.html

Phil

On 20/06/2020 02:20, Phil Addison wrote:
On Sat, 20 Jun 2020 00:09:32 +0100, in uk.d-i-y Nick wrote:

Good evening to all.

A dropbox pic he
https://www.dropbox.com/s/djbbkmbz14...0bolt.JPG?dl=0

I'm trying to put an old Wolf TG8B double ended 8 inch bench grinder
back in harness. Something of a challenge as it has been out in the
weather for about 15 years. All is probably Imperial as it was made in
West London 50 or 60 years ago.
The stones rotate, which is encouraging. I have removed the rests with
their rods from the main frame. This with the aid of some heat and a bit
of force. I have to go a bit steady as this old thing is mainly cast
aluminium. Slowly & steadily I will get the rest of it apart

The work rests are secured to steel rods by bolts that I have never seen
the like of.
The headless bolt is 1/2" dia by 2-1/2" long. Possibly a Whitworth
thread (advice on this would be much appreciated).
The bolt has a 'sort of' elongated C cut from it. When slackened this
would allow the work rest to be adjusted left/right and fore/aft. The
bolt I have removed is quite wasted, probably not reusable. I'm still
trying to free the second and may destroy it in the process.
Very possibly these are propriety items and Wolf disappeared to Kango et
al years ago.

Any thoughts please.

Many thanks,

It's a cotter-pin. They can be found fixing pedal cranks to the bottom-bracket shaft on older bicycles. Yours looks to be severely worn. The "C" shape is supposed to be a flat ground at a slight angle to the axis, the idea being that as it is tightened, the wedge shape jams firmly against a flat ground on the corresponding shaft. Also found securing the kick-start pedal on older motor-cycles, and anywhere a lever needs to be secured perpendicular to a shaft. If you're lucky yours may me a standard cycle size.

https://www.sheldonbrown.com/cotters.html

Phil

Not hard to get a bolt, remove its head and grind that shape into the
plain shaft section


--
"When a true genius appears in the world, you may know him by this sign,
that the dunces are all in confederacy against him."

Jonathan Swift.

Phil Addison wrote:
On Sat, 20 Jun 2020 00:09:32 +0100, in uk.d-i-y Nick wrote:

Good evening to all.

A dropbox pic he
https://www.dropbox.com/s/djbbkmbz14...0bolt.JPG?dl=0

I'm trying to put an old Wolf TG8B double ended 8 inch bench grinder
back in harness. Something of a challenge as it has been out in the
weather for about 15 years. All is probably Imperial as it was made in
West London 50 or 60 years ago.
The stones rotate, which is encouraging. I have removed the rests with
their rods from the main frame. This with the aid of some heat and a bit
of force. I have to go a bit steady as this old thing is mainly cast
aluminium. Slowly & steadily I will get the rest of it apart

The work rests are secured to steel rods by bolts that I have never seen
the like of.
The headless bolt is 1/2" dia by 2-1/2" long. Possibly a Whitworth
thread (advice on this would be much appreciated).
The bolt has a 'sort of' elongated C cut from it. When slackened this
would allow the work rest to be adjusted left/right and fore/aft. The
bolt I have removed is quite wasted, probably not reusable. I'm still
trying to free the second and may destroy it in the process.
Very possibly these are propriety items and Wolf disappeared to Kango et
al years ago.

Any thoughts please.

Many thanks,

It's a cotter-pin. They can be found fixing pedal cranks to the bottom-bracket shaft on older bicycles. Yours looks to be severely worn. The "C" shape is supposed to be a flat ground at a slight angle to the axis, the idea being that as it is tightened, the wedge shape jams firmly against a flat ground on the corresponding shaft. Also found securing the kick-start pedal on older motor-cycles, and anywhere a lever needs to be secured perpendicular to a shaft. If you're lucky yours may me a standard cycle size.

https://www.sheldonbrown.com/cotters.html

Phil

I've gone through enough of those over the years, on
my Mercier. I'm surprised that one was removed by driving
it out. When they get that distorted, sometimes you
have to drill them out.

Paul

+1 for cotter pin but you need to be careful searching, in the US a cotter pin is what in the UK is called a split pin. Search for cotter bolt and you will get bolts with holes in to take split pins. Agreed bicycle crank pins just have a wedge shaped flat but the type shown is common in machinery notably for clamping the shaft in place on a lathe tailstock. If you find it is not gripping because the worn part means the nut has run out of threads a botch would be to pack a few washers under the nut to get some grip back.

Richard

On 20/06/2020 02:19, John Rumm wrote:
....
It looks like the kind of thing that would be relatively easy to
fabricate. Find a bolt with the right pitch thread, and a smooth upper
part to the shank. Stick a nut on the end of it, and weld it on. Then
chop off the original hex head, leaving you with the same layout of hex
head, threaded section adjacent to it, and smooth shank beyond. Lastly
shape the required profile with a grinder.



Also, as it doesn't screw into any other part of the machine, you don't
have to match the thread, just the shank diameter.

--
Colin Bignell

"Phil Addison" wrote in message
...

On Sat, 20 Jun 2020 00:09:32 +0100, in uk.d-i-y Nick
wrote:

Good evening to all.

A dropbox pic he
https://www.dropbox.com/s/djbbkmbz14...0bolt.JPG?dl=0

Any thoughts please.

Many thanks,



It's a cotter-pin. https://www.sheldonbrown.com/cotters.html

Phil


Surely on a cotter pin the diameter of the threaded end has to be
thinner than the diameter of non threaded end to fit through the hole,
to be subsequently tightened.
In that picture the diameter of the threaded end looks to be much
thicker than the non threaded end so what's to stop it simply pulling
through any hole as its tightened ?


michael adams

....

On 20/06/2020 09:14, nightjar wrote:
On 20/06/2020 02:19, John Rumm wrote:
...
It looks like the kind of thing that would be relatively easy to
fabricate. Find a bolt with the right pitch thread, and a smooth upper
part to the shank. Stick a nut on the end of it, and weld it on. Then
chop off the original hex head, leaving you with the same layout of
hex head, threaded section adjacent to it, and smooth shank beyond.
Lastly shape the required profile with a grinder.



Also, as it doesn't screw into any other part of the machine, you don't
have to match the thread, just the shank diameter.

I'll bet it will be a standard imperial size. The shank diameter does
not have to be too accurate because pulling back against the angled flat
will tighten it. Actually I'm not convinced that it is particularly
badly worn either, the circular region at the left is machined to take
the cross member. As others have said, if you have "run out of threads"
it may be sufficient to add a couple of washers.

Also, I'm not convinced about the instructions above. I think you just
need to find a bolt with a long enough plain shank of the right
diameter, cut off the head and a bit of the shank if necessary, and
grind the shank to shape.

On 20/06/2020 00:09, Nick wrote:
Good evening to all.

A dropbox pic he
https://www.dropbox.com/s/djbbkmbz14...0bolt.JPG?dl=0

I'm trying to put an old Wolf TG8B double ended 8 inch bench grinder
back in harness. Something of a challenge as it has been out in the
weather for about 15 years. All is probably Imperial as it was made in
West London 50 or 60 years ago.
The stones rotate, which is encouraging. I have removed the rests with
their rods from the main frame. This with the aid of some heat and a bit
of force. I have to go a bit steady as this old thing is mainly cast
aluminium. Slowly & steadily I will get the rest of it apart

The work rests are secured to steel rods by bolts that I have never seen
the like of.
The headless bolt is 1/2" dia by 2-1/2" long. Possibly a Whitworth
thread (advice on this would be much appreciated).
The bolt has a 'sort of' elongated C cut from it. When slackened this
would allow the work rest to be adjusted left/right and fore/aft. The
bolt I have removed is quite wasted, probably not reusable. I'm still
trying to free the second and may destroy it in the process.
Very possibly these are propriety items and Wolf disappeared to Kango et
al years ago.

Any thoughts please.

Many thanks,

Nick

As others have said, it's a type of cotterpin.

You can make a replacement out of any suitable bolt with a plain shank
and matching nut, simply by cutting off the original head and grinding
the correct profile into the shank. [Not sure why John Rumm said to weld
the nut on - that sounds completely wrong!]

Matching the thread to the original isn't necessary - because the new
bolt's original nut will fit the new threads anyway.

The profile of the slot will depend on what it engages with. You say
that the rests are secured to steel rods. If these are pure cylindrical
rods with no notches or flats, the bit to grind out will be a portion of
a circle to fit the radius of the rods. If the rest can be rotated
around its support rod, this sounds like the most likely.
--
Cheers,
Roger

On Saturday, 20 June 2020 12:52:46 UTC+1, michael adams wrote:
"Phil Addison" wrote in message
...

On Sat, 20 Jun 2020 00:09:32 +0100, in uk.d-i-y Nick
wrote:

Good evening to all.

A dropbox pic he
https://www.dropbox.com/s/djbbkmbz14...0bolt.JPG?dl=0

Any thoughts please.

Many thanks,



It's a cotter-pin. https://www.sheldonbrown.com/cotters.html

Phil


Surely on a cotter pin the diameter of the threaded end has to be
thinner than the diameter of non threaded end to fit through the hole,
to be subsequently tightened.
In that picture the diameter of the threaded end looks to be much
thicker than the non threaded end so what's to stop it simply pulling
through any hole as its tightened ?

Yes, you're right.
Bicycle crank cotterpins have the threaded bit smaller than the smallest bit of the shaft with the taper ground in.
It's not a conventional cotterpin.

On Sat, 20 Jun 2020 12:52:43 +0100, in uk.d-i-y "michael adams" wrote:


"Phil Addison" wrote in message
...

On Sat, 20 Jun 2020 00:09:32 +0100, in uk.d-i-y Nick
wrote:

Good evening to all.

A dropbox pic he
https://www.dropbox.com/s/djbbkmbz14...0bolt.JPG?dl=0

Any thoughts please.

Many thanks,



It's a cotter-pin. https://www.sheldonbrown.com/cotters.html

Phil


Surely on a cotter pin the diameter of the threaded end has to be
thinner than the diameter of non threaded end to fit through the hole,
to be subsequently tightened.

Yes, you are right concerning a cotter pin, but it has to be smaller at the thread end because the full diameter is obstructed by the flat on the shaft that the wedge has to engage with. However, I concede that the thing in the OP's post is not a bicycle type cotter pin as others have pointed out.

Incidentally bicycles no longer use cotter pins, instead the cranks are typically secured either to a tapered square section, or a spline system on the crank shaft. And you need a puller to separate them, a hammer is no longer any use!

Phil

"harry" wrote in message
...
On Saturday, 20 June 2020 12:52:46 UTC+1, michael adams wrote:
"Phil Addison" wrote in message
...

On Sat, 20 Jun 2020 00:09:32 +0100, in uk.d-i-y Nick
wrote:

Good evening to all.

A dropbox pic he
https://www.dropbox.com/s/djbbkmbz14...0bolt.JPG?dl=0

Any thoughts please.

Many thanks,



It's a cotter-pin. https://www.sheldonbrown.com/cotters.html

Phil


Surely on a cotter pin the diameter of the threaded end has to be
thinner than the diameter of non threaded end to fit through the hole,
to be subsequently tightened.
In that picture the diameter of the threaded end looks to be much
thicker than the non threaded end so what's to stop it simply pulling
through any hole as its tightened ?

Yes, you're right.
Bicycle crank cotterpins have the threaded bit smaller than the smallest bit
of the shaft with the taper ground in.
It's not a conventional cotterpin.

A bicycle cotterpin locates in slot machined in the axle. This also positions the
crank on the axle preventing it sliding in or out.So its necessary to first mount
the crank on the axle and line up the hole before inserting the cotter pin.

With the bolt in the picture it looks as though this procedure must be reversed.
So the bolt is inserted into the crank equivalent and when the holes lines up
the axle is fed through this. If theres a sholder at one end of the axle this will
prevent sliding along the axle in one direction but not in the other.


michael adams

....

"Phil Addison" wrote in message
...
Incidentally bicycles no longer use cotter pins, instead the cranks
are typically secured either to a tapered square section, or a spline
system on the crank shaft. And you need a puller to separate them,
a hammer is no longer any use!


Cotterless cranks have threads inside the holes. A crank extractor
threads into these which itself has a threaded hole in the centre.
A hardened steel pin is screwed into this which then acts against
the end of the axle thus forcing the crank off the axle. Or quite
possibly instead this simply strips the thread from inside the crank.
Which in the absence of an expensive specialist tool may then require
the use of a cold chisel and/or crowbar, liberal amounts of heat from
a gas torch, and quite possibly the use of a hammer.


michael adams

....

Roger Mills wrote:

On 20/06/2020 00:09, Nick wrote:
Good evening to all.

A dropbox pic he
https://www.dropbox.com/s/djbbkmbz14...0bolt.JPG?dl=0

I'm trying to put an old Wolf TG8B double ended 8 inch bench grinder
back in harness. Something of a challenge as it has been out in the
weather for about 15 years. All is probably Imperial as it was made in
West London 50 or 60 years ago.
The stones rotate, which is encouraging. I have removed the rests with
their rods from the main frame. This with the aid of some heat and a bit
of force. I have to go a bit steady as this old thing is mainly cast
aluminium. Slowly & steadily I will get the rest of it apart

The work rests are secured to steel rods by bolts that I have never seen
the like of.
The headless bolt is 1/2" dia by 2-1/2" long. Possibly a Whitworth
thread (advice on this would be much appreciated).
The bolt has a 'sort of' elongated C cut from it. When slackened this
would allow the work rest to be adjusted left/right and fore/aft. The
bolt I have removed is quite wasted, probably not reusable. I'm still
trying to free the second and may destroy it in the process.
Very possibly these are propriety items and Wolf disappeared to Kango et
al years ago.

Any thoughts please.

Many thanks,

Nick

As others have said, it's a type of cotterpin.

You can make a replacement out of any suitable bolt with a plain shank
and matching nut, simply by cutting off the original head and grinding
the correct profile into the shank. [Not sure why John Rumm said to weld
the nut on - that sounds completely wrong!]

Matching the thread to the original isn't necessary - because the new
bolt's original nut will fit the new threads anyway.

The profile of the slot will depend on what it engages with. You say
that the rests are secured to steel rods. If these are pure cylindrical
rods with no notches or flats, the bit to grind out will be a portion of
a circle to fit the radius of the rods. If the rest can be rotated
around its support rod, this sounds like the most likely.

A trapezoidal truncated pyramid like the original is probably a lot
easier for an amateur like myself to approximate to with a grinder and
will work nearly as well.

--

Roger Hayter

On Sat, 20 Jun 2020 20:45:30 +0100, in uk.d-i-y "michael adams" wrote:


"Phil Addison" wrote in message
...
Incidentally bicycles no longer use cotter pins, instead the cranks
are typically secured either to a tapered square section, or a spline
system on the crank shaft. And you need a puller to separate them,
a hammer is no longer any use!


Cotterless cranks have threads inside the holes. A crank extractor
threads into these which itself has a threaded hole in the centre.
A hardened steel pin is screwed into this which then acts against
the end of the axle thus forcing the crank off the axle. Or quite
possibly instead this simply strips the thread from inside the crank.

This can happen if the puller/extractor is not fully screwed in before attempting the extraction. Or possibly if someone has previously partly stripped the thread like that.

Which in the absence of an expensive specialist tool may then require
the use of a cold chisel and/or crowbar, liberal amounts of heat from
a gas torch, and quite possibly the use of a hammer.

Phil

On 20/06/2020 14:04, Roger Mills wrote:
On 20/06/2020 00:09, Nick wrote:
Good evening to all.

A dropbox pic he
https://www.dropbox.com/s/djbbkmbz14...0bolt.JPG?dl=0

I'm trying to put an old Wolf TG8B double ended 8 inch bench grinder
back in harness. Something of a challenge as it has been out in the
weather for about 15 years. All is probably Imperial as it was made in
West London 50 or 60 years ago.
The stones rotate, which is encouraging. I have removed the rests with
their rods from the main frame. This with the aid of some heat and a
bit of force. I have to go a bit steady as this old thing is mainly
cast aluminium. Slowly & steadily I will get the rest of it apart

The work rests are secured to steel rods by bolts that I have never
seen the like of.
The headless bolt is 1/2" dia by 2-1/2" long. Possibly a Whitworth
thread (advice on this would be much appreciated).
The bolt has a 'sort of' elongated C cut from it. When slackened this
would allow the work rest to be adjusted left/right and fore/aft. The
bolt I have removed is quite wasted, probably not reusable. I'm still
trying to free the second and may destroy it in the process.
Very possibly these are propriety items and Wolf disappeared to Kango
et al years ago.

Any thoughts please.

Many thanks,

Nick

As others have said, it's a type of cotterpin.

You can make a replacement out of any suitable bolt with a plain shank
and matching nut, simply by cutting off the original head and grinding
the correct profile into the shank. [Not sure why John Rumm said to weld
the nut on - that sounds completely wrong!]

I was assuming from the OPs description of it as a "bolt", that the hex
section shown in the photo was a fixed head, and not a nut[.

If it is indeed a nut on the original, its even simpler - omit welding
it on! :-)


--
Cheers,

John.

/================================================== ===============\
| Internode Ltd - http://www.internode.co.uk |
|-----------------------------------------------------------------|
| John Rumm - john(at)internode(dot)co(dot)uk |
\================================================= ================/

On 21/06/2020 01:34, John Rumm wrote:
On 20/06/2020 14:04, Roger Mills wrote:
On 20/06/2020 00:09, Nick wrote:
Good evening to all.

A dropbox pic he
https://www.dropbox.com/s/djbbkmbz14...0bolt.JPG?dl=0

I'm trying to put an old Wolf TG8B double ended 8 inch bench grinder
back in harness. Something of a challenge as it has been out in the
weather for about 15 years. All is probably Imperial as it was made
in West London 50 or 60 years ago.
The stones rotate, which is encouraging. I have removed the rests
with their rods from the main frame. This with the aid of some heat
and a bit of force. I have to go a bit steady as this old thing is
mainly cast aluminium. Slowly & steadily I will get the rest of it apart

The work rests are secured to steel rods by bolts that I have never
seen the like of.
The headless bolt is 1/2" dia by 2-1/2" long. Possibly a Whitworth
thread (advice on this would be much appreciated).
The bolt has a 'sort of' elongated C cut from it. When slackened this
would allow the work rest to be adjusted left/right and fore/aft. The
bolt I have removed is quite wasted, probably not reusable. I'm still
trying to free the second and may destroy it in the process.
Very possibly these are propriety items and Wolf disappeared to Kango
et al years ago.

Any thoughts please.

Many thanks,

Nick

As others have said, it's a type of cotterpin.

You can make a replacement out of any suitable bolt with a plain shank
and matching nut, simply by cutting off the original head and grinding
the correct profile into the shank. [Not sure why John Rumm said to
weld the nut on - that sounds completely wrong!]

I was assuming from the OPs description of it as a "bolt", that the hex
section shown in the photo was a fixed head, and not a nut[.

If it is indeed a nut on the original, its even simpler - omit welding
it on! :-)



It has to be nut, to tension the bolt/pin so that it clamps onto the
support bar.

--
Cheers,
Roger