Home |
Search |
Today's Posts |
|
UK diy (uk.d-i-y) For the discussion of all topics related to diy (do-it-yourself) in the UK. All levels of experience and proficency are welcome to join in to ask questions or offer solutions. |
Reply |
|
LinkBack | Thread Tools | Display Modes |
#1
Posted to uk.d-i-y
|
|||
|
|||
TEKS screws
I've been asked to attach some fixings to steel sheet using hexagonal- headed TEKS screws (as already used for similar fixings in the same location). These, apparently are self tapping - but do they need a pilot hole? If not, how do I start them off? Are they meant to be driven by a spanner, or a power tool? -- Andy Mabbett * Say "NO!" to compulsory ID Cards: http://www.no2id.net/ * Free Our Data: http://www.freeourdata.org.uk * Are you using Microformats, yet: http://microformats.org/ ? |
#2
Posted to uk.d-i-y
|
|||
|
|||
TEKS screws
"Andy Mabbett" wrote in message ... I've been asked to attach some fixings to steel sheet using hexagonal- headed TEKS screws (as already used for similar fixings in the same location). These, apparently are self tapping - but do they need a pilot hole? If not, how do I start them off? Are they meant to be driven by a spanner, or a power tool? -- Andy Mabbett The ones I used roofing one of my buildings in steel profile sheeting just sat in a hex socket in my Wickes bat op drill, and with an initial stout push went in nicely. They had a cutting edge ground on the point, and the screw bit only started after maybe a mm or so. AWEM |
#3
Posted to uk.d-i-y
|
|||
|
|||
TEKS screws
In article ,
Andy Mabbett wrote: I've been asked to attach some fixings to steel sheet using hexagonal- headed TEKS screws (as already used for similar fixings in the same location). These, apparently are self tapping - but do they need a pilot hole? If not, how do I start them off? Are they meant to be driven by a spanner, or a power tool? If they are what I'm thinking of they have a 'drill' on the tip of the screw so are truly a one shot approach to fixing into sheet metal. A drill with a suitable socket on the end is all you need - although a centre punch helps if you need accurate spacing, etc. -- *If you lived in your car, you'd be home by now * Dave Plowman London SW To e-mail, change noise into sound. |
#4
Posted to uk.d-i-y
|
|||
|
|||
TEKS screws
In message , "Dave Plowman (News)"
writes In article , Andy Mabbett wrote: I've been asked to attach some fixings to steel sheet using hexagonal- headed TEKS screws (as already used for similar fixings in the same location). These, apparently are self tapping - but do they need a pilot hole? If not, how do I start them off? Are they meant to be driven by a spanner, or a power tool? A drill with a suitable socket on the end is all you need - although a centre punch helps if you need accurate spacing, etc. Thanks to both who replied - that did the trick. -- Andy Mabbett * Say "NO!" to compulsory ID Cards: http://www.no2id.net/ * Free Our Data: http://www.freeourdata.org.uk * Are you using Microformats, yet: http://microformats.org/ ? |
Reply |
Thread Tools | Search this Thread |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Forum | |||
Using sheet metal, particle board, or drywall screws in wood, and help finding source for black wood screws | Woodworking | |||
Are 'screws' available. | UK diy | |||
Need a few 2-56 UNC screws | UK diy | |||
Sheetmetal screws, chassis screws, fastening idears | Metalworking | |||
screws don't go in far enough | Woodworking |