Home |
Search |
Today's Posts |
|
Metalworking (rec.crafts.metalworking) Discuss various aspects of working with metal, such as machining, welding, metal joining, screwing, casting, hardening/tempering, blacksmithing/forging, spinning and hammer work, sheet metal work. |
Reply |
|
LinkBack | Thread Tools | Display Modes |
|
#1
Posted to rec.crafts.metalworking
|
|||
|
|||
PING: Iggy
You have any of these? Not related or anything. Just came across this ad.
Working on an old Lincoln SA-200 welding machine with a Red Seal continental F-163 motor. Want to Buy --- Service manuals. http://muskegon.craigslist.org/wan/2765256407.html -- Steve Walker (remove brain when replying) |
#2
Posted to rec.crafts.metalworking
|
|||
|
|||
PING: Iggy
On 2011-12-23, Steve Walker wrote:
You have any of these? Not related or anything. Just came across this ad. Working on an old Lincoln SA-200 welding machine with a Red Seal continental F-163 motor. Want to Buy --- Service manuals. http://muskegon.craigslist.org/wan/2765256407.html I have them available online. http://igor.chudov.com/manuals/Continental-Engines/ I emailed that guy. Maybe it will help him. Anyone wants a Pipeliner 400 welder with a Perkins 4-262 diesel engine, with only TWO HOURS on the engine? With a military trailer? i |
#3
Posted to rec.crafts.metalworking
|
|||
|
|||
PING: Iggy
On 2011-12-23, Ignoramus22709 wrote:
On 2011-12-23, Steve Walker wrote: You have any of these? Not related or anything. Just came across this ad. Working on an old Lincoln SA-200 welding machine with a Red Seal continental F-163 motor. Want to Buy --- Service manuals. http://muskegon.craigslist.org/wan/2765256407.html I have them available online. http://igor.chudov.com/manuals/Continental-Engines/ I emailed that guy. Maybe it will help him. Anyone wants a Pipeliner 400 welder with a Perkins 4-262 diesel engine, with only TWO HOURS on the engine? With a military trailer? i He replied, saying that he does not want downloads. I think that his ads is a little bit not genuine, he is not working on anything, he wants to buy them for resale. i |
#4
Posted to rec.crafts.metalworking
|
|||
|
|||
PING: Iggy
On Thu, 22 Dec 2011 21:30:59 -0600, Ignoramus22709
wrote: On 2011-12-23, Steve Walker wrote: You have any of these? Not related or anything. Just came across this ad. Working on an old Lincoln SA-200 welding machine with a Red Seal continental F-163 motor. Want to Buy --- Service manuals. http://muskegon.craigslist.org/wan/2765256407.html I have them available online. http://igor.chudov.com/manuals/Continental-Engines/ I emailed that guy. Maybe it will help him. Anyone wants a Pipeliner 400 welder with a Perkins 4-262 diesel engine, with only TWO HOURS on the engine? With a military trailer? i How much? Got a pic? Could sell that easily here in the oil patch. Gunner One could not be a successful Leftwinger without realizing that, in contrast to the popular conception supported by newspapers and mothers of Leftwingers, a goodly number of Leftwingers are not only narrow-minded and dull, but also just stupid. Gunner Asch |
#5
Posted to rec.crafts.metalworking
|
|||
|
|||
PING: Iggy
On 2011-12-24, Gunner Asch wrote:
On Thu, 22 Dec 2011 21:30:59 -0600, Ignoramus22709 wrote: On 2011-12-23, Steve Walker wrote: You have any of these? Not related or anything. Just came across this ad. Working on an old Lincoln SA-200 welding machine with a Red Seal continental F-163 motor. Want to Buy --- Service manuals. http://muskegon.craigslist.org/wan/2765256407.html I have them available online. http://igor.chudov.com/manuals/Continental-Engines/ I emailed that guy. Maybe it will help him. Anyone wants a Pipeliner 400 welder with a Perkins 4-262 diesel engine, with only TWO HOURS on the engine? With a military trailer? i How much? Got a pic? Could sell that easily here in the oil patch. It will be comparatively expensive due to 2 hours, Perkins 4.236 engine and military origin (assuming it still works). It is on trailer with a lot of cabinets etc. Room to put on tanks, a compressor also. Pix are here http://igor.chudov.com/tmp/Military-Hobart-Welder/ I still have to go through the EUC process. I doubt that I will sell it through this newsgroup ($8k), and will ask for more elsewhere. i |
#6
Posted to rec.crafts.metalworking
|
|||
|
|||
PING: Iggy
On Sat, 24 Dec 2011 07:18:49 -0600, Ignoramus22709
wrote: On 2011-12-24, Gunner Asch wrote: On Thu, 22 Dec 2011 21:30:59 -0600, Ignoramus22709 wrote: On 2011-12-23, Steve Walker wrote: You have any of these? Not related or anything. Just came across this ad. Working on an old Lincoln SA-200 welding machine with a Red Seal continental F-163 motor. Want to Buy --- Service manuals. http://muskegon.craigslist.org/wan/2765256407.html I have them available online. http://igor.chudov.com/manuals/Continental-Engines/ I emailed that guy. Maybe it will help him. Anyone wants a Pipeliner 400 welder with a Perkins 4-262 diesel engine, with only TWO HOURS on the engine? With a military trailer? i How much? Got a pic? Could sell that easily here in the oil patch. It will be comparatively expensive due to 2 hours, Perkins 4.236 engine and military origin (assuming it still works). It is on trailer with a lot of cabinets etc. Room to put on tanks, a compressor also. Pix are here http://igor.chudov.com/tmp/Military-Hobart-Welder/ I still have to go through the EUC process. I doubt that I will sell it through this newsgroup ($8k), and will ask for more elsewhere. i Nice rig!! What did you get it for? Gunner One could not be a successful Leftwinger without realizing that, in contrast to the popular conception supported by newspapers and mothers of Leftwingers, a goodly number of Leftwingers are not only narrow-minded and dull, but also just stupid. Gunner Asch |
#7
Posted to rec.crafts.metalworking
|
|||
|
|||
PING: Iggy
On 2011-12-24, Gunner Asch wrote:
On Sat, 24 Dec 2011 07:18:49 -0600, Ignoramus22709 wrote: On 2011-12-24, Gunner Asch wrote: On Thu, 22 Dec 2011 21:30:59 -0600, Ignoramus22709 wrote: On 2011-12-23, Steve Walker wrote: You have any of these? Not related or anything. Just came across this ad. Working on an old Lincoln SA-200 welding machine with a Red Seal continental F-163 motor. Want to Buy --- Service manuals. http://muskegon.craigslist.org/wan/2765256407.html I have them available online. http://igor.chudov.com/manuals/Continental-Engines/ I emailed that guy. Maybe it will help him. Anyone wants a Pipeliner 400 welder with a Perkins 4-262 diesel engine, with only TWO HOURS on the engine? With a military trailer? i How much? Got a pic? Could sell that easily here in the oil patch. It will be comparatively expensive due to 2 hours, Perkins 4.236 engine and military origin (assuming it still works). It is on trailer with a lot of cabinets etc. Room to put on tanks, a compressor also. Pix are here http://igor.chudov.com/tmp/Military-Hobart-Welder/ I still have to go through the EUC process. I doubt that I will sell it through this newsgroup ($8k), and will ask for more elsewhere. i Nice rig!! What did you get it for? $4k, Kind of a lot of money, that's why I have to ask for so much. It cost the military $43k. http://www.govliquidation.com/auctio...ategoryId=1004 This is a huge welder, with a 64-80 HP Perkins (depending on who to believe). Of course, I am taking a risk that it is not functional, such as engine rusted inside or the injection pump seals rotted. I am generally optimistic and, to date, I had very good luck with diesel powered equipment. The price, obviously, assumes that the welder works. If it works, I will ask for $9-10k elsewhere. i |
#8
Posted to rec.crafts.metalworking
|
|||
|
|||
Lincoln TIG welder problems
Does anyone have a schematic of the circuit boards in a Lincoln
Square Wave TIG 300? I have what Lincoln releases to to public, which is just a wiring diagram of the whole machine. All the PC boards are just squares on the drawing. When I got it (used) I was able to trace down the bad Tantalum capacitor that caused the shield gas postflow to stay on forever. Now I have a more difficult problem to solve. When the machine is first turned on after a period of not being used, I can't get any arc current. It indicates 72 V and 0-7 Amps on the LED meters, even if the electrode is shorted to the ground clamp. The high frequency works like mad, but there is no main arc current. It seems to take 10-15 minutes of trying, and suddenly jumps to life. This last time I fiddles with the switches again, and that's when it started working, so it could be a dirty contact in the HF start/always/off switch. But, in previous cases it just started working at one point with no flipping of switches. Has anyone else seen a similar problem with a Lincoln square wave TIG machine? I am suspecting another bad capacitor, but it would be hard to track down without detailed schematics of the boards. Thanks for any hints in the right direction. Another problem is the torch is getting plugged up and I have to run the cooler for minutes before there is just the most meager flow. The outlet from the cooler is plenty strong. Is there something I can put in the torch to flush it out? (I discovered the tank in the cooler had slowly evaporated, and was really low. I added a bunch of water. next time at the welding place I will get a new batch of cooler fluid and replace.) I filled it originally with this greenish stuff specifically sold for TIG coolers. Thanks, again. Jon |
#9
Posted to rec.crafts.metalworking
|
|||
|
|||
Lincoln TIG welder problems
Jon Elson wrote: Does anyone have a schematic of the circuit boards in a Lincoln Square Wave TIG 300? I have what Lincoln releases to to public, which is just a wiring diagram of the whole machine. All the PC boards are just squares on the drawing. When I got it (used) I was able to trace down the bad Tantalum capacitor that caused the shield gas postflow to stay on forever. Now I have a more difficult problem to solve. When the machine is first turned on after a period of not being used, I can't get any arc current. It indicates 72 V and 0-7 Amps on the LED meters, even if the electrode is shorted to the ground clamp. The high frequency works like mad, but there is no main arc current. It seems to take 10-15 minutes of trying, and suddenly jumps to life. This last time I fiddles with the switches again, and that's when it started working, so it could be a dirty contact in the HF start/always/off switch. But, in previous cases it just started working at one point with no flipping of switches. Has anyone else seen a similar problem with a Lincoln square wave TIG machine? I am suspecting another bad capacitor, but it would be hard to track down without detailed schematics of the boards. Thanks for any hints in the right direction. Another problem is the torch is getting plugged up and I have to run the cooler for minutes before there is just the most meager flow. The outlet from the cooler is plenty strong. Is there something I can put in the torch to flush it out? (I discovered the tank in the cooler had slowly evaporated, and was really low. I added a bunch of water. next time at the welding place I will get a new batch of cooler fluid and replace.) I filled it originally with this greenish stuff specifically sold for TIG coolers. That sounds like you may have some bad electrolytics on the conrtroller board. The ESR drops some as they heat up, and start working. http://www.radiolocman.com/shem/shem....html?di=20764 is a '99 cent ESR meter' and gives some basic information on testing them. -- You can't have a sense of humor, if you have no sense. |
#10
Posted to rec.crafts.metalworking
|
|||
|
|||
Lincoln TIG welder problems
Michael A. Terrell wrote:
That sounds like you may have some bad electrolytics on the conrtroller board. The ESR drops some as they heat up, and start working. The main board has dozens of large Tantalum capacitors, and older tantalum caps tend to fail with various symptoms when not kept polarized fairly frequently. I already fixed one bad one that was pretty easy to locate, the postflow timer. This fault, if it is a capacitor, is going to take more detective work. The board is conformally coated, so any rework is a very painful process involving carving the coating off with an X-acto knife. So, shotgunning all the dozens of caps on the board is not practical. Jon |
#11
Posted to rec.crafts.metalworking
|
|||
|
|||
Lincoln TIG welder problems
On 12/27/2011 12:28 PM, Jon Elson wrote:
Michael A. Terrell wrote: That sounds like you may have some bad electrolytics on the conrtroller board. The ESR drops some as they heat up, and start working. The main board has dozens of large Tantalum capacitors, and older tantalum caps tend to fail with various symptoms when not kept polarized fairly frequently. I already fixed one bad one that was pretty easy to locate, the postflow timer. This fault, if it is a capacitor, is going to take more detective work. The board is conformally coated, so any rework is a very painful process involving carving the coating off with an X-acto knife. So, shotgunning all the dozens of caps on the board is not practical. Jon you may want to spend $80 and buy an ESR meter - that will help you find bad caps easily - there is one called "blue" that is a kit, easy to assemble, you can get it from ebay or from the factory |
#12
Posted to rec.crafts.metalworking
|
|||
|
|||
Lincoln TIG welder problems
Bill wrote: On 12/27/2011 12:28 PM, Jon Elson wrote: Michael A. Terrell wrote: That sounds like you may have some bad electrolytics on the conrtroller board. The ESR drops some as they heat up, and start working. The main board has dozens of large Tantalum capacitors, and older tantalum caps tend to fail with various symptoms when not kept polarized fairly frequently. I already fixed one bad one that was pretty easy to locate, the postflow timer. This fault, if it is a capacitor, is going to take more detective work. The board is conformally coated, so any rework is a very painful process involving carving the coating off with an X-acto knife. So, shotgunning all the dozens of caps on the board is not practical. Jon you may want to spend $80 and buy an ESR meter - that will help you find bad caps easily - there is one called "blue" that is a kit, easy to assemble, you can get it from ebay or from the factory I posted a link to a simple "99 cent" adapter to use a scope to test ESR, upthread. -- You can't have a sense of humor, if you have no sense. |
#13
Posted to rec.crafts.metalworking
|
|||
|
|||
Lincoln TIG welder problems
Jon Elson wrote: Michael A. Terrell wrote: That sounds like you may have some bad electrolytics on the conrtroller board. The ESR drops some as they heat up, and start working. The main board has dozens of large Tantalum capacitors, and older tantalum caps tend to fail with various symptoms when not kept polarized fairly frequently. I already fixed one bad one that was pretty easy to locate, the postflow timer. This fault, if it is a capacitor, is going to take more detective work. The board is conformally coated, so any rework is a very painful process involving carving the coating off with an X-acto knife. So, shotgunning all the dozens of caps on the board is not practical. A hot soldering iron should cut throught the conformal coating. If it is a hard and shiny coating, GC Printkote Solvent may remove it where you need to work. If it's the soft rubbery crap, it can cause problems of it's own. I don't shotgun, I find the failures. -- You can't have a sense of humor, if you have no sense. |
#14
Posted to rec.crafts.metalworking
|
|||
|
|||
Lincoln TIG welder problems
Michael A. Terrell wrote:
A hot soldering iron should cut throught the conformal coating. If it is a hard and shiny coating, GC Printkote Solvent may remove it where you need to work. If it's the soft rubbery crap, it can cause problems of it's own. I don't shotgun, I find the failures. Yes, and that is why knowing which 2 or 3 caps would be the most likely suspects is the only way to deal with this. The Lincoln Square Wave TIG is a rather complicated machine, the main board is about a foot square with several dozen 4000-series CMOS chips on it. I think there is an SCR trigger board that also has over a dozen chips. Burning through the coating with a soldering iron is hard on the iron and makes a real mess of the board, too, making resoldering difficult later. The coating, as I remember, is the hard stuff. So, I'm hoping somebody can come up with a diagram of the boards. Thanks, Jon |
#15
Posted to rec.crafts.metalworking
|
|||
|
|||
Lincoln TIG welder problems
On Mon, 26 Dec 2011 21:23:56 -0600, Jon Elson
wrote: Does anyone have a schematic of the circuit boards in a Lincoln Square Wave TIG 300? I have what Lincoln releases to to public, which is just a wiring diagram of the whole machine. All the PC boards are just squares on the drawing. When I got it (used) I was able to trace down the bad Tantalum capacitor that caused the shield gas postflow to stay on forever. Now I have a more difficult problem to solve. When the machine is first turned on after a period of not being used, I can't get any arc current. It indicates 72 V and 0-7 Amps on the LED meters, even if the electrode is shorted to the ground clamp. The high frequency works like mad, but there is no main arc current. It seems to take 10-15 minutes of trying, and suddenly jumps to life. This last time I fiddles with the switches again, and that's when it started working, so it could be a dirty contact in the HF start/always/off switch. But, in previous cases it just started working at one point with no flipping of switches. Has anyone else seen a similar problem with a Lincoln square wave TIG machine? I am suspecting another bad capacitor, but it would be hard to track down without detailed schematics of the boards. Thanks for any hints in the right direction. Another problem is the torch is getting plugged up and I have to run the cooler for minutes before there is just the most meager flow. The outlet from the cooler is plenty strong. Is there something I can put in the torch to flush it out? (I discovered the tank in the cooler had slowly evaporated, and was really low. I added a bunch of water. next time at the welding place I will get a new batch of cooler fluid and replace.) I filled it originally with this greenish stuff specifically sold for TIG coolers. Thanks, again. Jon I recently gave one one of those away. Mine would preform normally on AC..but when swtiched to DC..no matter what the setting..it was 300 amps at the torch. No matter the polarity...300 amps at the torch. Yet AC worked just fine. The guy I gave it to does mostly aluminum, but says he will have it looked after..one of these days. I may..may have the schematics for it..Ill check Shrug Gunner One could not be a successful Leftwinger without realizing that, in contrast to the popular conception supported by newspapers and mothers of Leftwingers, a goodly number of Leftwingers are not only narrow-minded and dull, but also just stupid. Gunner Asch |
#16
Posted to rec.crafts.metalworking
|
|||
|
|||
Lincoln TIG welder problems
Gunner Asch wrote:
I may..may have the schematics for it..Ill check I'd greatly appreciate it! I have the machine wiring, which is helpful, but no details on the boards themselves. Jon |
#17
Posted to rec.crafts.metalworking
|
|||
|
|||
Lincoln TIG welder problems
Gunner Asch wrote: I recently gave one one of those away. Mine would preform normally on AC..but when swtiched to DC..no matter what the setting..it was 300 amps at the torch. No matter the polarity...300 amps at the torch. Yet AC worked just fine. The guy I gave it to does mostly aluminum, but says he will have it looked after..one of these days. I may..may have the schematics for it..Ill check If you have board level schematics, I'd love to have a copy. -- You can't have a sense of humor, if you have no sense. |
Reply |
Thread Tools | Search this Thread |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Forum | |||
Ping Iggy | Metalworking | |||
Ping: Iggy | Metalworking | |||
Ping: Iggy | Metalworking | |||
Ping - Iggy.. | Metalworking | |||
Ping: Iggy | Metalworking |