Ignoramus12820 wrote:

On 2010-08-20, Buerste wrote:
Any idea what spindle runout you get on those while they are
relatively new?

Sorry, that was never a concern. We rout a 2" x 1/8" x 2-1/2" groove in
Beech. It's not to critical, just good enough to index a long handle. What
runout are you looking for?

I am not sure, the less the better, 0.003-4 worst case, hopefully
better. It would be OK for engraving, but not for precision work. I
really do not know what I will be dealing with.

i

When you get your router, you need to chuck up something that fits the collet that is
accurate. Likely your engraving bit will do up where the shaft is biggest.

Using a test indicator. http://www.mitutoyo.com/Images%5C002...5C513-442T.jpg

Check the router for run out. You might be able to clock the collet to improve run out.
Wood is more forgiving than metal

I use a .0001" resolution one like that quite often at work. For some things it isn't
good enough but for the majority of lining up things it gets the job done.


Wes

--
"Additionally as a security officer, I carry a gun to protect
government officials but my life isn't worth protecting at home
in their eyes." Dick Anthony Heller

On 2010-08-20, Wes wrote:
Ignoramus12820 wrote:

On 2010-08-20, Buerste wrote:
Any idea what spindle runout you get on those while they are
relatively new?

Sorry, that was never a concern. We rout a 2" x 1/8" x 2-1/2" groove in
Beech. It's not to critical, just good enough to index a long handle. What
runout are you looking for?

I am not sure, the less the better, 0.003-4 worst case, hopefully
better. It would be OK for engraving, but not for precision work. I
really do not know what I will be dealing with.

i

When you get your router, you need to chuck up something that fits the collet that is
accurate. Likely your engraving bit will do up where the shaft is biggest.

Using a test indicator. http://www.mitutoyo.com/Images%5C002...5C513-442T.jpg

Check the router for run out. You might be able to clock the collet to improve run out.
Wood is more forgiving than metal

I use a .0001" resolution one like that quite often at work. For some things it isn't
good enough but for the majority of lining up things it gets the job done.

Wes, yes, I will definitely measure runout with a dial indicator. I
will post the result. I am not expecting miracles.

i

On Fri, 20 Aug 2010 17:40:23 -0500, Ignoramus11290
wrote:

On 2010-08-20, Wes wrote:
Ignoramus12820 wrote:

On 2010-08-20, Buerste wrote:
Any idea what spindle runout you get on those while they are
relatively new?

Sorry, that was never a concern. We rout a 2" x 1/8" x 2-1/2" groove in
Beech. It's not to critical, just good enough to index a long handle. What
runout are you looking for?

I am not sure, the less the better, 0.003-4 worst case, hopefully
better. It would be OK for engraving, but not for precision work. I
really do not know what I will be dealing with.

i

When you get your router, you need to chuck up something that fits the collet that is
accurate. Likely your engraving bit will do up where the shaft is biggest.

Using a test indicator. http://www.mitutoyo.com/Images%5C002...5C513-442T.jpg

Check the router for run out. You might be able to clock the collet to improve run out.
Wood is more forgiving than metal

I use a .0001" resolution one like that quite often at work. For some things it isn't
good enough but for the majority of lining up things it gets the job done.

Wes, yes, I will definitely measure runout with a dial indicator. I
will post the result. I am not expecting miracles.

i

Dial indicator or dial Test indicator? You need an indicator that will
measure .0001

Gunner

--


"First Law of Leftist Debate
The more you present a leftist with factual evidence
that is counter to his preconceived world view and the
more difficult it becomes for him to refute it without
losing face the chance of him calling you a racist, bigot,
homophobe approaches infinity.

This is despite the thread you are in having not mentioned
race or sexual preference in any way that is relevant to
the subject." Grey Ghost

On 2010-08-21, Gunner Asch wrote:
On Fri, 20 Aug 2010 17:40:23 -0500, Ignoramus11290
wrote:

On 2010-08-20, Wes wrote:
Ignoramus12820 wrote:

On 2010-08-20, Buerste wrote:
Any idea what spindle runout you get on those while they are
relatively new?

Sorry, that was never a concern. We rout a 2" x 1/8" x 2-1/2" groove in
Beech. It's not to critical, just good enough to index a long handle. What
runout are you looking for?

I am not sure, the less the better, 0.003-4 worst case, hopefully
better. It would be OK for engraving, but not for precision work. I
really do not know what I will be dealing with.

i

When you get your router, you need to chuck up something that fits the collet that is
accurate. Likely your engraving bit will do up where the shaft is biggest.

Using a test indicator. http://www.mitutoyo.com/Images%5C002...5C513-442T.jpg

Check the router for run out. You might be able to clock the collet to improve run out.
Wood is more forgiving than metal

I use a .0001" resolution one like that quite often at work. For some things it isn't
good enough but for the majority of lining up things it gets the job done.

Wes, yes, I will definitely measure runout with a dial indicator. I
will post the result. I am not expecting miracles.

i

Dial indicator or dial Test indicator? You need an indicator that will
measure .0001

I have both, but I expect runout to be around 0.003".

i

On Fri, 20 Aug 2010 19:20:26 -0500, Ignoramus11290
wrote:

On 2010-08-21, Gunner Asch wrote:
On Fri, 20 Aug 2010 17:40:23 -0500, Ignoramus11290
wrote:

On 2010-08-20, Wes wrote:
Ignoramus12820 wrote:

On 2010-08-20, Buerste wrote:
Any idea what spindle runout you get on those while they are
relatively new?

Sorry, that was never a concern. We rout a 2" x 1/8" x 2-1/2" groove in
Beech. It's not to critical, just good enough to index a long handle. What
runout are you looking for?

I am not sure, the less the better, 0.003-4 worst case, hopefully
better. It would be OK for engraving, but not for precision work. I
really do not know what I will be dealing with.

i

When you get your router, you need to chuck up something that fits the collet that is
accurate. Likely your engraving bit will do up where the shaft is biggest.

Using a test indicator. http://www.mitutoyo.com/Images%5C002...5C513-442T.jpg

Check the router for run out. You might be able to clock the collet to improve run out.
Wood is more forgiving than metal

I use a .0001" resolution one like that quite often at work. For some things it isn't
good enough but for the majority of lining up things it gets the job done.

Wes, yes, I will definitely measure runout with a dial indicator. I
will post the result. I am not expecting miracles.

i

Dial indicator or dial Test indicator? You need an indicator that will
measure .0001

I have both, but I expect runout to be around 0.003".

i

Then use a "tenths" indicator to get a good, true reading.

Using a .001 indicator will show you jack ****.

Really. I do this for a living...
G

Gunner

--


"First Law of Leftist Debate
The more you present a leftist with factual evidence
that is counter to his preconceived world view and the
more difficult it becomes for him to refute it without
losing face the chance of him calling you a racist, bigot,
homophobe approaches infinity.

This is despite the thread you are in having not mentioned
race or sexual preference in any way that is relevant to
the subject." Grey Ghost