Metalworking (rec.crafts.metalworking) Discuss various aspects of working with metal, such as machining, welding, metal joining, screwing, casting, hardening/tempering, blacksmithing/forging, spinning and hammer work, sheet metal work.

 
 
LinkBack Thread Tools Search this Thread Display Modes
Prev Previous Post   Next Post Next
  #8   Report Post  
Posted to rec.crafts.metalworking
external usenet poster
 
Posts: 544
Default Off grid power generation, AC vs DC

On Tue, 15 Sep 2009 15:52:35 -0700 (PDT), "
wrote:

Hey folks, I've been having trouble getting an answer to my question
from off grid sites. I'm hoping someone can help me or point to the
right place. I am planning an off grid system. The house will be run
off of a bank of batteries with an inverter to supply AC power. My
question is on the charging of the batteries. In general, is it
better to supply the batteries with DC power generated consistently
over time or to supply AC through a charge controller for shorter
periods. I plan to use solar and wind but may have to rely on a
generator for some periods. The generator is the part that has me
stumped. Tho the generator will run off renewable fuels, I'm unsure
whether to run a large generator making AC for a short time, or run a
smaller generator making DC power for a long time. I had considered
an engine small enough to drive generators the size of those found in
wind generators. Any help or direction would be appreciated. Thanks,
Paul


Generally, you size your renewable supply (solar or wind or whatever)
to keep up with your consumption, plus some reserve charging capacity
to get recharged in a reasonable period after discharging your
batteries. Then you size the backup generator to charge at a similar
rate. For example, at my place www.citlink.net/~wmbjk/solar100.htm,
solar is 2000W nameplate, and wind is 1000W. Charge rates vary
considerably depending on whether one or the other or both sources are
generating, and how much load is concurrent. There's really no such
thing as average, but I'd say that the normal charging rate we see is
about 40A after loads. Our primary backup generator produces about
70A. We rarely discharge below about 70%, and that generator can get
us back up to about 90% in 3 or 4 hours, depending on loads. For a
while I used a 140A generator, but that was too much. You'd need to
supply a lot of information to get a good recommendation on the best
balance for your application, and even then opinions will vary. But in
general, you want the *smallest* generator that will do the job. I
suggest that you post your info at alt.energy.homepower, or at the
Outback forum. Either way, lots of knowledgeable folks will offer
real-world experience.

Wayne
 
Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules

Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
QUESTION: How to connect a power supply to my home power grid? S Claus Electronics 6 July 29th 09 01:08 PM
Power Grid failures - are these logged online? kerplunk UK diy 11 August 6th 06 10:12 PM
Accuracy of UK power grid time control? Mike Berger Electronics Repair 76 April 19th 06 11:56 PM
Off-grid power (long) Colin Blackburn UK diy 19 February 4th 05 12:10 PM
next generation of power tools S R Woodworking 14 January 14th 05 03:45 AM


All times are GMT +1. The time now is 09:42 AM.

Powered by vBulletin® Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.
Copyright ©2004-2025 DIYbanter.
The comments are property of their posters.
 

About Us

"It's about DIY & home improvement"