Home |
Search |
Today's Posts |
|
Metalworking (rec.crafts.metalworking) Discuss various aspects of working with metal, such as machining, welding, metal joining, screwing, casting, hardening/tempering, blacksmithing/forging, spinning and hammer work, sheet metal work. |
Reply |
|
LinkBack | Thread Tools | Display Modes |
#1
Posted to rec.crafts.metalworking
|
|||
|
|||
Lyon Modular Cabinet Lock Mechanism
Yesterday I picked up two tool cabinets, both eye height, an 11 drawer
Vidmar and a 17 drawer Lyon. The Lyon had a poor attempt to unlock via drilling, then some sort of mangling which bent the lock mechanism. I got them home and unloaded via a Uhaul trailer. The Vidmar is re-assembled and ready to receive tools. I want to repair the lock mechanism on the Lyon before reassembly. I've managed to remove the drilled lock. The locking mechanism in the back of the cabinet, on the other hand, is more of a challenge. The operating rod hole at the front, locking mechanism bolt hole at the back, and lock bar pivot (the lock bar is built up to resemble a vertical angle which pivots into a recess in each drawer frame to lock all drawers) at the back are all curved slots which have been closed enough to prevent removal of much anything. I can almost, but not quite remove the locking mechanism over the lock bar pivot. This sucker was not intended to be disassembled. Tomorrow, I plan to file or grind the slots enough to allow removal of the operating rod, lock mechanism, and lock bar. At that point I'll be able to straighten the lock mechanism and determine everything's working before I reinstall. A trip to the locksmith should provide a new lock. Anybody got any other suggestions for opening the slots? Thanks. Pete Keillor |
#2
Posted to rec.crafts.metalworking
|
|||
|
|||
Lyon Modular Cabinet Lock Mechanism
Tomorrow, I plan to file or grind the slots enough to allow removal of the operating rod, lock mechanism, and lock bar. �At that point I'll be able to straighten the lock mechanism and determine everything's working before I reinstall. �A trip to the locksmith should provide a new lock. Anybody got any other suggestions for opening the slots? Thanks. Pete Keillor Pete If you do the metalwork to straighten it up you will be better off. I did one a few years ago. If I recall the latching bar was bent and I had to pound the bottom of the door some. (Had to take to door off.) I am reasonably sure there are new parts available from Lyons. Perhaps they have a web address/site. Bob AZ |
#3
Posted to rec.crafts.metalworking
|
|||
|
|||
Lyon Modular Cabinet Lock Mechanism
A file made short work of the below this morning. Took less time than
the post. Now I just need to find that lock. Pete On Fri, 21 Aug 2009 17:25:38 -0400, Pete Keillor wrote: Yesterday I picked up two tool cabinets, both eye height, an 11 drawer Vidmar and a 17 drawer Lyon. The Lyon had a poor attempt to unlock via drilling, then some sort of mangling which bent the lock mechanism. I got them home and unloaded via a Uhaul trailer. The Vidmar is re-assembled and ready to receive tools. I want to repair the lock mechanism on the Lyon before reassembly. I've managed to remove the drilled lock. The locking mechanism in the back of the cabinet, on the other hand, is more of a challenge. The operating rod hole at the front, locking mechanism bolt hole at the back, and lock bar pivot (the lock bar is built up to resemble a vertical angle which pivots into a recess in each drawer frame to lock all drawers) at the back are all curved slots which have been closed enough to prevent removal of much anything. I can almost, but not quite remove the locking mechanism over the lock bar pivot. This sucker was not intended to be disassembled. Tomorrow, I plan to file or grind the slots enough to allow removal of the operating rod, lock mechanism, and lock bar. At that point I'll be able to straighten the lock mechanism and determine everything's working before I reinstall. A trip to the locksmith should provide a new lock. Anybody got any other suggestions for opening the slots? Thanks. Pete Keillor |
Reply |
Thread Tools | Search this Thread |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Forum | |||
Toolmakers Cabinet Lock | Woodworking | |||
Help with filing cabinet lock/key combination | UK diy | |||
Need help impressioning barrel key cabinet lock | Home Repair | |||
Need help impressioning barrel key cabinet lock | Woodworking | |||
missing washing machine lid, need to bypass lock mechanism! | Home Ownership |