Metalworking (rec.crafts.metalworking) Discuss various aspects of working with metal, such as machining, welding, metal joining, screwing, casting, hardening/tempering, blacksmithing/forging, spinning and hammer work, sheet metal work.

Reply
 
LinkBack Thread Tools Search this Thread Display Modes
  #1   Report Post  
zephyr
 
Posts: n/a
Default Magnetic Chuck Repair Question

I have just obtained a 6 X 18 magnetic chuck. I think the brand is Walker,
but I can't tell for sure because the nameplate is missing. The On - Off
lever works hard and I was wondering if I should attempt to disassemble the
chuck to see if I could fix it. Is this something that can be easily done?

John


  #2   Report Post  
Randal O'Brian
 
Posts: n/a
Default Magnetic Chuck Repair Question

I took mine apart, mainly out of curiosity. It was 8 or 10 years ago, but I
don't remember any real problem taking it apart other than magnetic
attraction trying to keep it together. The sliding parts are grease lubed
and it may be that the grease in yours has dried up and hardened.

Randy

"zephyr" wrote in message
...
I have just obtained a 6 X 18 magnetic chuck. I think the brand is

Walker,
but I can't tell for sure because the nameplate is missing. The On - Off
lever works hard and I was wondering if I should attempt to disassemble

the
chuck to see if I could fix it. Is this something that can be easily

done?

John




  #3   Report Post  
DoN. Nichols
 
Posts: n/a
Default Magnetic Chuck Repair Question

In article ,
Randal O'Brian wrote:
I took mine apart, mainly out of curiosity. It was 8 or 10 years ago, but I
don't remember any real problem taking it apart other than magnetic
attraction trying to keep it together. The sliding parts are grease lubed
and it may be that the grease in yours has dried up and hardened.


It depends on the type of permanent magnet in there. Unless it
is one of the modern rare-earth magnets, the assembly acts as a
"keeper", and with it apart, the field strength of the permanent magnet
will drop significantly, and it will need to be re-polled once it is
reassembled.

So -- generally, I would suggest *not* disassembling it unless
it is so bad as to be useless.

If you do disassemble it, first lock it onto some object of a
known size and measure the force needed to pull it straight off. Then
after you have it cleaned and reassembled, repeat the test. This will
tell you whether you have lost field strength.

I understand that some places offer the service of re-polling
the chucks -- but I have never tried to find someone who will do it, so
I don't know what your luck will be.

Good Luck,
DoN.
--
Email: | Voice (all times): (703) 938-4564
(too) near Washington D.C. | http://www.d-and-d.com/dnichols/DoN.html
--- Black Holes are where God is dividing by zero ---
Reply
Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules

Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
Chuck question Roger Hull Metalworking 6 January 16th 04 03:31 AM
magnetic chuck problem Kenneth W. Sterling Metalworking 3 August 30th 03 05:37 PM
Cuemaking-Metal Lathe Chuck Question? J. Alan Metalworking 6 August 9th 03 02:07 AM
Magnetic chuck weirdness Mike Graham Metalworking 1 July 13th 03 08:17 AM


All times are GMT +1. The time now is 10:19 PM.

Powered by vBulletin® Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004-2024 DIYbanter.
The comments are property of their posters.
 

About Us

"It's about DIY & home improvement"