Home |
Search |
Today's Posts |
|
Home Repair (alt.home.repair) For all homeowners and DIYers with many experienced tradesmen. Solve your toughest home fix-it problems. |
Reply |
|
LinkBack | Thread Tools | Display Modes |
|
#1
Posted to alt.home.repair
|
|||
|
|||
Is There An Electrician in the House?
I knew I had a problem yesterday morning when the furnace didn't come on at
the usual 6:30 time where it progresses from the thermostat's nighttime setting into the waking time setting. Investigation revealed about half the house was without power, and half normal. I quickly ran extension cords to power the critical items (furnace, refrigerator, computer) to working outlets. Clearly one leg of the 120v supply was out. After cycling all the breakers, including the master, without success I decided it was time to pick an electrician out of the phone book, and the firm promised someone within an hour. While waiting outside for the electrician, a neighbor came out with exactly the same complaint. I knew then that it was a utility company problem, but having commited to the service call decided there was no harm other than a few $$$ in having the issue confirmed. (Turned out to be a burnt wire in an underground connection vault, and it took them until 10:30 in the evening to restore full power.) The gentleman was quickly able to confirm my hypothesis, but then pointed out some alleged issues in my breaker box. I personally choose not to fool with breaker boxes, other than tightening the screws on the blasted aluminum wire once every year or so; I'm comfortable with wiring and conduit manipulation and the like, but feel breaker boxes are left to pros. He pointed out one breaker which had two wires going into it. Being copper, I knew this was a circuit I had had (professionally) added in the past, but being on the nonfunctional leg neither he nor I could determine what was being powered from this breaker. He claimed that was highly dangerous. Now that I have power again, I'll be able to ascertain what's being powered from that breaker, but my question is: is this automatically a Highly Bad Thing, or are there instances where two wires into one breaker is a legitimate installation? He wanted $450 to correct this, which given the triviality of snapping two breakers into a box and connecting a wire to each seemed to me to be a ripoff in the making, so I declined. He also suggested that since many of the breakers were quite old (it's a 1969 house, although some circuits have been added over the years), and since replacing them all would be expensive, that I have him "lubricate" the breakers. I had visions of duct-cleaning "services" in my head, and simply sent him on his merry way after paying the basic service fee. Was he blowing smoke, or did he know something about circuit breakers not apparent to me? Art |
#2
Posted to alt.home.repair
|
|||
|
|||
Is There An Electrician in the House?
Arthur Shapiro wrote: I knew I had a problem yesterday morning when the furnace didn't come on at the usual 6:30 time where it progresses from the thermostat's nighttime setting into the waking time setting. Investigation revealed about half the house was without power, and half normal. I quickly ran extension cords to power the critical items (furnace, refrigerator, computer) to working outlets. Clearly one leg of the 120v supply was out. After cycling all the breakers, including the master, without success I decided it was time to pick an electrician out of the phone book, and the firm promised someone within an hour. While waiting outside for the electrician, a neighbor came out with exactly the same complaint. I knew then that it was a utility company problem, but having commited to the service call decided there was no harm other than a few $$$ in having the issue confirmed. (Turned out to be a burnt wire in an underground connection vault, and it took them until 10:30 in the evening to restore full power.) The gentleman was quickly able to confirm my hypothesis, but then pointed out some alleged issues in my breaker box. I personally choose not to fool with breaker boxes, other than tightening the screws on the blasted aluminum wire once every year or so; I'm comfortable with wiring and conduit manipulation and the like, but feel breaker boxes are left to pros. He pointed out one breaker which had two wires going into it. Being copper, I knew this was a circuit I had had (professionally) added in the past, but being on the nonfunctional leg neither he nor I could determine what was being powered from this breaker. He claimed that was highly dangerous. Now that I have power again, I'll be able to ascertain what's being powered from that breaker, but my question is: is this automatically a Highly Bad Thing, or are there instances where two wires into one breaker is a legitimate installation? He wanted $450 to correct this, which given the triviality of snapping two breakers into a box and connecting a wire to each seemed to me to be a ripoff in the making, so I declined. He also suggested that since many of the breakers were quite old (it's a 1969 house, although some circuits have been added over the years), and since replacing them all would be expensive, that I have him "lubricate" the breakers. I had visions of duct-cleaning "services" in my head, and simply sent him on his merry way after paying the basic service fee. Was he blowing smoke, or did he know something about circuit breakers not apparent to me? Art Hi, my little book on basic home wiring repairs says having two wires on a screw down connection is not a good idea. It suggests a pigtail and wire nut . That said I have much the same in my breaker box. I have heard suggestions that breakers be manually thrown and reset to ensure they are functioning corectly about once a year. The lubrication thing sounds reasonable to me for a mechanical device if in a high dust area . After all I lubricate hinges , locksets , and stuff regularly. A breaker inside a box though I dont know. I would have thought that hinge points would be self lubricating materials . Your post is a good tip though . If you lose one phase of the supply, every other breaker its probably a supply problem . |
#3
Posted to alt.home.repair
|
|||
|
|||
Is There An Electrician in the House?
|
#4
Posted to alt.home.repair
|
|||
|
|||
Is There An Electrician in the House?
I vote for smoke on this one. Arthur Shapiro wrote: I knew I had a problem yesterday morning when the furnace didn't come on at the usual 6:30 time where it progresses from the thermostat's nighttime setting into the waking time setting. Investigation revealed about half the house was without power, and half normal. I quickly ran extension cords to power the critical items (furnace, refrigerator, computer) to working outlets. Clearly one leg of the 120v supply was out. After cycling all the breakers, including the master, without success I decided it was time to pick an electrician out of the phone book, and the firm promised someone within an hour. While waiting outside for the electrician, a neighbor came out with exactly the same complaint. I knew then that it was a utility company problem, but having commited to the service call decided there was no harm other than a few $$$ in having the issue confirmed. (Turned out to be a burnt wire in an underground connection vault, and it took them until 10:30 in the evening to restore full power.) The gentleman was quickly able to confirm my hypothesis, but then pointed out some alleged issues in my breaker box. I personally choose not to fool with breaker boxes, other than tightening the screws on the blasted aluminum wire once every year or so; I'm comfortable with wiring and conduit manipulation and the like, but feel breaker boxes are left to pros. He pointed out one breaker which had two wires going into it. Being copper, I knew this was a circuit I had had (professionally) added in the past, but being on the nonfunctional leg neither he nor I could determine what was being powered from this breaker. He claimed that was highly dangerous. Now that I have power again, I'll be able to ascertain what's being powered from that breaker, but my question is: is this automatically a Highly Bad Thing, or are there instances where two wires into one breaker is a legitimate installation? He wanted $450 to correct this, which given the triviality of snapping two breakers into a box and connecting a wire to each seemed to me to be a ripoff in the making, so I declined. He also suggested that since many of the breakers were quite old (it's a 1969 house, although some circuits have been added over the years), and since replacing them all would be expensive, that I have him "lubricate" the breakers. I had visions of duct-cleaning "services" in my head, and simply sent him on his merry way after paying the basic service fee. Was he blowing smoke, or did he know something about circuit breakers not apparent to me? Art |
#5
Posted to alt.home.repair
|
|||
|
|||
Is There An Electrician in the House?
Yeah, me too. If it ain't broke, don't fix it...
061220 1532 - 7 LAMPSTICKS 7 FEASTS 7 AGES OF DISPENSATION posted: I vote for smoke on this one. Arthur Shapiro wrote: I knew I had a problem yesterday morning when the furnace didn't come on at the usual 6:30 time where it progresses from the thermostat's nighttime setting into the waking time setting. Investigation revealed about half the house was without power, and half normal. I quickly ran extension cords to power the critical items (furnace, refrigerator, computer) to working outlets. Clearly one leg of the 120v supply was out. After cycling all the breakers, including the master, without success I decided it was time to pick an electrician out of the phone book, and the firm promised someone within an hour. While waiting outside for the electrician, a neighbor came out with exactly the same complaint. I knew then that it was a utility company problem, but having commited to the service call decided there was no harm other than a few $$$ in having the issue confirmed. (Turned out to be a burnt wire in an underground connection vault, and it took them until 10:30 in the evening to restore full power.) The gentleman was quickly able to confirm my hypothesis, but then pointed out some alleged issues in my breaker box. I personally choose not to fool with breaker boxes, other than tightening the screws on the blasted aluminum wire once every year or so; I'm comfortable with wiring and conduit manipulation and the like, but feel breaker boxes are left to pros. He pointed out one breaker which had two wires going into it. Being copper, I knew this was a circuit I had had (professionally) added in the past, but being on the nonfunctional leg neither he nor I could determine what was being powered from this breaker. He claimed that was highly dangerous. Now that I have power again, I'll be able to ascertain what's being powered from that breaker, but my question is: is this automatically a Highly Bad Thing, or are there instances where two wires into one breaker is a legitimate installation? He wanted $450 to correct this, which given the triviality of snapping two breakers into a box and connecting a wire to each seemed to me to be a ripoff in the making, so I declined. He also suggested that since many of the breakers were quite old (it's a 1969 house, although some circuits have been added over the years), and since replacing them all would be expensive, that I have him "lubricate" the breakers. I had visions of duct-cleaning "services" in my head, and simply sent him on his merry way after paying the basic service fee. Was he blowing smoke, or did he know something about circuit breakers not apparent to me? Art |
#6
Posted to alt.home.repair
|
|||
|
|||
Is There An Electrician in the House?
"Arthur Shapiro" wrote in message ... I knew I had a problem yesterday morning when the furnace didn't come on at the usual 6:30 time where it progresses from the thermostat's nighttime setting into the waking time setting. Investigation revealed about half the house was without power, and half normal. I quickly ran extension cords to power the critical items (furnace, refrigerator, computer) to working outlets. Clearly one leg of the 120v supply was out. After cycling all the breakers, including the master, without success I decided it was time to pick an electrician out of the phone book, and the firm promised someone within an hour. While waiting outside for the electrician, a neighbor came out with exactly the same complaint. I knew then that it was a utility company problem, but having commited to the service call decided there was no harm other than a few $$$ in having the issue confirmed. (Turned out to be a burnt wire in an underground connection vault, and it took them until 10:30 in the evening to restore full power.) The gentleman was quickly able to confirm my hypothesis, but then pointed out some alleged issues in my breaker box. I personally choose not to fool with breaker boxes, other than tightening the screws on the blasted aluminum wire once every year or so; I'm comfortable with wiring and conduit manipulation and the like, but feel breaker boxes are left to pros. He pointed out one breaker which had two wires going into it. Being copper, I knew this was a circuit I had had (professionally) added in the past, but being on the nonfunctional leg neither he nor I could determine what was being powered from this breaker. He claimed that was highly dangerous. Now that I have power again, I'll be able to ascertain what's being powered from that breaker, but my question is: is this automatically a Highly Bad Thing, or are there instances where two wires into one breaker is a legitimate installation? He wanted $450 to correct this, which given the triviality of snapping two breakers into a box and connecting a wire to each seemed to me to be a ripoff in the making, so I declined. He also suggested that since many of the breakers were quite old (it's a 1969 house, although some circuits have been added over the years), and since replacing them all would be expensive, that I have him "lubricate" the breakers. I had visions of duct-cleaning "services" in my head, and simply sent him on his merry way after paying the basic service fee. Was he blowing smoke, or did he know something about circuit breakers not apparent to me? If the breaker is rated for 2 wires, it is not a problem. If not, then you can pigtail. I am assuming that the breaker is properly rated for the smaller of the two circuits. While that seems obvious, my cottage had three 20a circuits going to a 50a breaker. Very dangerous. The other issue is capacity; had they installed a 20a breaker at my cottage the load on the three circuits would have tripped the breaker. I had to put them on three 20a breakers. Personally I would split it up. In all likelihood you can resolve it for $10 and 5 minutes work. It is probably easier than putting an outlet in. People are scared of the breaker box cause there is so much power there, but 120v is 120v. (I know there is 240v at the box, but you would have to really try to contact more than 120v) I have never heard of old breakers being dangerous or lubricating them, and I surely wouldn't do anything to them that the manufacturer didn't recommend. But if you are concerned, you can probably replace them all for $100 in an hour. As a matter of fact, I just had a 1965 breaker trip when a mouse chewed through a wire and shorted it. |
#7
Posted to alt.home.repair
|
|||
|
|||
Is There An Electrician in the House?
Toller wrote:
I have never heard of old breakers being dangerous or lubricating them, and I surely wouldn't do anything to them that the manufacturer didn't recommend. Maybe he was describing removing the breakers and applying a little Thomas & Betts Kopper Shield or a silver conductive grease to the "plug in" prongs to make sure they maintained good contact: http://www.elexp.com/che_8463.htm But if you are concerned, you can probably replace them all for $100 in an hour. As a matter of fact, I just had a 1965 breaker trip when a mouse chewed through a wire and shorted it. Did the rodent survive? Jeff -- Jeffry Wisnia (W1BSV + Brass Rat '57 EE) The speed of light is 1.8*10^12 furlongs per fortnight. |
#8
Posted to alt.home.repair
|
|||
|
|||
Is There An Electrician in the House?
Jeff Wisnia wrote:
Toller wrote: I have never heard of old breakers being dangerous or lubricating them, and I surely wouldn't do anything to them that the manufacturer didn't recommend. Maybe he was describing removing the breakers and applying a little Thomas & Betts Kopper Shield or a silver conductive grease to the "plug in" prongs to make sure they maintained good contact: http://www.elexp.com/che_8463.htm I suspect removing and replacing the breakers compromises their connections more than this stuff improves them. And I'd be concerned it might migrate, too. But if you are concerned, you can probably replace them all for $100 in an hour. As a matter of fact, I just had a 1965 breaker trip when a mouse chewed through a wire and shorted it. Did the rodent survive? Jeff -- The e-mail address in our reply-to line is reversed in an attempt to minimize spam. Our true address is of the form . |
#9
Posted to alt.home.repair
|
|||
|
|||
Is There An Electrician in the House?
Arthur Shapiro wrote: I knew I had a problem yesterday morning when the furnace didn't come on at the usual 6:30 time where it progresses from the thermostat's nighttime setting into the waking time setting. Investigation revealed about half the house was without power, and half normal. I quickly ran extension cords to power the critical items (furnace, refrigerator, computer) to working outlets. Clearly one leg of the 120v supply was out. After cycling all the breakers, including the master, without success I decided it was time to pick an electrician out of the phone book, and the firm promised someone within an hour. While waiting outside for the electrician, a neighbor came out with exactly the same complaint. I knew then that it was a utility company problem, but having commited to the service call decided there was no harm other than a few $$$ in having the issue confirmed. (Turned out to be a burnt wire in an underground connection vault, and it took them until 10:30 in the evening to restore full power.) The gentleman was quickly able to confirm my hypothesis, but then pointed out some alleged issues in my breaker box. I personally choose not to fool with breaker boxes, other than tightening the screws on the blasted aluminum wire once every year or so; I'm comfortable with wiring and conduit manipulation and the like, but feel breaker boxes are left to pros. He pointed out one breaker which had two wires going into it. Being copper, I knew this was a circuit I had had (professionally) added in the past, but being on the nonfunctional leg neither he nor I could determine what was being powered from this breaker. He claimed that was highly dangerous. Now that I have power again, I'll be able to ascertain what's being powered from that breaker, but my question is: is this automatically a Highly Bad Thing, or are there instances where two wires into one breaker is a legitimate installation? He wanted $450 to correct this, which given the triviality of snapping two breakers into a box and connecting a wire to each seemed to me to be a ripoff in the making, so I declined. He also suggested that since many of the breakers were quite old (it's a 1969 house, although some circuits have been added over the years), and since replacing them all would be expensive, that I have him "lubricate" the breakers. I had visions of duct-cleaning "services" in my head, and simply sent him on his merry way after paying the basic service fee. Was he blowing smoke, or did he know something about circuit breakers not apparent to me? Art Sounds totally bogus. In that a screw terminal will grab two similar single-strand Cu wires just as well as one. Only possible reason for splitting wires, IMHO, would depend on the circuits fed. $450 for popping in one breaker? End of discussion. When power's back on, you can check the draw on each wire with clamp-on ammeter, and see what's happening there. I assume you know what all the loads are on that feed. Lubricating breakers? Right. OTOH, you mention Al wiring. I'd save up all small change to pay for verifying, changing all connections to safe ones; properly crimp on pigtails, whatever. Al connections are a huge danger. J |
#10
Posted to alt.home.repair
|
|||
|
|||
Is There An Electrician in the House?
|
#11
Posted to alt.home.repair
|
|||
|
|||
Is There An Electrician in the House?
"Arthur Shapiro" wrote in message
... While waiting outside for the electrician, a neighbor came out with exactly the same complaint. I knew then that it was a utility company problem.... I'm just watching this discussion, but maybe someone can explain how a problem with the utility's equipment could cause just half a house to go dead. |
#12
Posted to alt.home.repair
|
|||
|
|||
Is There An Electrician in the House?
"JoeSpareBedroom" wrote in message ... "Arthur Shapiro" wrote in message ... While waiting outside for the electrician, a neighbor came out with exactly the same complaint. I knew then that it was a utility company problem.... I'm just watching this discussion, but maybe someone can explain how a problem with the utility's equipment could cause just half a house to go dead. You have two 120v circuits going to your house. Half the house's 120v circuits are on each. It is important not to use any 240v devices while there is a problem, since they would only get 120v. |
#13
Posted to alt.home.repair
|
|||
|
|||
Is There An Electrician in the House?
"Toller" wrote in message ... "JoeSpareBedroom" wrote in message ... "Arthur Shapiro" wrote in message ... While waiting outside for the electrician, a neighbor came out with exactly the same complaint. I knew then that it was a utility company problem.... I'm just watching this discussion, but maybe someone can explain how a problem with the utility's equipment could cause just half a house to go dead. You have two 120v circuits going to your house. Half the house's 120v circuits are on each. It is important not to use any 240v devices while there is a problem, since they would only get 120v. Thanks. |
#14
Posted to alt.home.repair
|
|||
|
|||
Is There An Electrician in the House?
On Wed, 20 Dec 2006 21:01:19 GMT, "Toller" wrote:
"JoeSpareBedroom" wrote in message ... "Arthur Shapiro" wrote in message ... While waiting outside for the electrician, a neighbor came out with exactly the same complaint. I knew then that it was a utility company problem.... I'm just watching this discussion, but maybe someone can explain how a problem with the utility's equipment could cause just half a house to go dead. You have two 120v circuits going to your house. Half the house's 120v circuits are on each. It is important not to use any 240v devices while there is a problem, since they would only get 120v. The appliance could still give you a shock if you were to work on it, but turning it on wouldn't hurt anything. It would just not work. |
#15
Posted to alt.home.repair
|
|||
|
|||
Is There An Electrician in the House?
On Wed, 20 Dec 2006 21:01:19 GMT, "Toller" wrote:
"JoeSpareBedroom" wrote in message ... "Arthur Shapiro" wrote in message ... While waiting outside for the electrician, a neighbor came out with exactly the same complaint. I knew then that it was a utility company problem.... I'm just watching this discussion, but maybe someone can explain how a problem with the utility's equipment could cause just half a house to go dead. You have two 120v circuits going to your house. Half the house's 120v circuits are on each. It is important not to use any 240v devices while there is a problem, since they would only get 120v. The failed connection is probably open, not shorted to ground. You would get nothing, not 120V. -- 4 days until the winter solstice celebration Mark Lloyd http://notstupid.laughingsquid.com "Never underestimate the power of stupid people in large groups" |
#16
Posted to alt.home.repair
|
|||
|
|||
Is There An Electrician in the House?
JoeSpareBedroom wrote:
"Arthur Shapiro" wrote in message ... While waiting outside for the electrician, a neighbor came out with exactly the same complaint. I knew then that it was a utility company problem.... I'm just watching this discussion, but maybe someone can explain how a problem with the utility's equipment could cause just half a house to go dead. In the words of Mad Max: "There's a big difference between all dead and mostly dead." There are two phases dropped to the house, 120 each. If you lose one, you still have the other. Circuit breaker boxes are designed to alternate the phases to successive breakers. When you lose one phase, roughly half the 120v circuits go dead. As to how the power company can lose a phase, think a half-fried transformer. But sometimes they just lose things. About twenty years ago, the light company lost one of my payments for about a year. |
#17
Posted to alt.home.repair
|
|||
|
|||
Is There An Electrician in the House?
HeyBub wrote:
There are two phases dropped to the house, 120 each. If you lose one, you still have the other. ....................... snip ................... Also: While agreeing that the term 'phase' is sometimes used ......................... More correctly there are two 'legs' which are the opposite ends of the same centre tapped 230 volt single phase! Thus one can be considered (sort of, although incorrectly as far as AC is concerned) as being plus 120 volts and the other as neg. 120 volts and therefore about 240 volts between the two of them; which is used to power heavy y items such as water heaters, electric cooking stoves etc. If the the two wires were really different phases they would have voltages 120 degrees apart and there would be a peculiar voltage between the two. Not the 230/240 volts (180 degrees with the two ends always of opposite polarity) expected. Same thing happened to my neighbours garage; they lost one side (or leg) of the 230 volt supply. The 'electrician' they hired came over to my house to borrow a multimeter and I went over and checked it for them! Utility company fixed a defective over head drop later that day. |
#18
Posted to alt.home.repair
|
|||
|
|||
Is There An Electrician in the House?
"terry" wrote in message
ups.com... HeyBub wrote: There are two phases dropped to the house, 120 each. If you lose one, you still have the other. ....................... snip ................... Also: While agreeing that the term 'phase' is sometimes used ........................ More correctly there are two 'legs' which are the opposite ends of the same centre tapped 230 volt single phase! Thus one can be considered (sort of, although incorrectly as far as AC is concerned) as being plus 120 volts and the other as neg. 120 volts and therefore about 240 volts between the two of them; which is used to power heavy y items such as water heaters, electric cooking stoves etc. If the the two wires were really different phases they would have voltages 120 degrees apart and there would be a peculiar voltage between the two. Not the 230/240 volts (180 degrees with the two ends always of opposite polarity) expected. Same thing happened to my neighbours garage; they lost one side (or leg) of the 230 volt supply. The 'electrician' they hired came over to my house to borrow a multimeter and I went over and checked it for them! Utility company fixed a defective over head drop later that day. Losing one leg is not all that uncommon, at least around here. I've seen this at least three time in the past year -- all problems that the local utility had to fix. As another poster has mentioned - the tip off is if every other circuit is off. Also, be careful of back feeds through 220v appliances like ranges, water heaters and dryers. |
#19
Posted to alt.home.repair
|
|||
|
|||
Is There An Electrician in the House?
On Thu, 21 Dec 2006 09:48:39 -0500, "The Streets" wrote:
"terry" wrote in message oups.com... HeyBub wrote: There are two phases dropped to the house, 120 each. If you lose one, you still have the other. ....................... snip ................... Also: While agreeing that the term 'phase' is sometimes used ........................ More correctly there are two 'legs' which are the opposite ends of the same centre tapped 230 volt single phase! Thus one can be considered (sort of, although incorrectly as far as AC is concerned) as being plus 120 volts and the other as neg. 120 volts and therefore about 240 volts between the two of them; which is used to power heavy y items such as water heaters, electric cooking stoves etc. If the the two wires were really different phases they would have voltages 120 degrees apart and there would be a peculiar voltage between the two. Not the 230/240 volts (180 degrees with the two ends always of opposite polarity) expected. Same thing happened to my neighbours garage; they lost one side (or leg) of the 230 volt supply. The 'electrician' they hired came over to my house to borrow a multimeter and I went over and checked it for them! Utility company fixed a defective over head drop later that day. Losing one leg is not all that uncommon, at least around here. I've seen this at least three time in the past year -- all problems that the local utility had to fix. As another poster has mentioned - the tip off is if every other circuit is off. Also, be careful of back feeds through 220v appliances like ranges, water heaters and dryers. I'll bite. Suppose I've got a (residential) 200A main breaker panel, and the street power fails. I switch off the main breaker and use a gas powered 40A generator to backfeed the 30A (220v) circuit for the elec. dryer. What can I expect? Live circuits, dead circuits? Overload conditions?? Elec. power around here (MO) seems to get less and less reliable by the month, else I wouldn't ask. Thx, Puddin' Pease pudding hot, Pease pudding cold, Pease pudding in the pot Nine days old ... |
#20
Posted to alt.home.repair
|
|||
|
|||
Is There An Electrician in the House?
Why not pull that breaker and install a tandem breaker? Or move one wire to
another breaker? That way the two circuits each have their own breaker. "Arthur Shapiro" wrote in message ... I knew I had a problem yesterday morning when the furnace didn't come on at the usual 6:30 time where it progresses from the thermostat's nighttime setting into the waking time setting. Investigation revealed about half the house was without power, and half normal. I quickly ran extension cords to power the critical items (furnace, refrigerator, computer) to working outlets. Clearly one leg of the 120v supply was out. After cycling all the breakers, including the master, without success I decided it was time to pick an electrician out of the phone book, and the firm promised someone within an hour. While waiting outside for the electrician, a neighbor came out with exactly the same complaint. I knew then that it was a utility company problem, but having commited to the service call decided there was no harm other than a few $$$ in having the issue confirmed. (Turned out to be a burnt wire in an underground connection vault, and it took them until 10:30 in the evening to restore full power.) The gentleman was quickly able to confirm my hypothesis, but then pointed out some alleged issues in my breaker box. I personally choose not to fool with breaker boxes, other than tightening the screws on the blasted aluminum wire once every year or so; I'm comfortable with wiring and conduit manipulation and the like, but feel breaker boxes are left to pros. He pointed out one breaker which had two wires going into it. Being copper, I knew this was a circuit I had had (professionally) added in the past, but being on the nonfunctional leg neither he nor I could determine what was being powered from this breaker. He claimed that was highly dangerous. Now that I have power again, I'll be able to ascertain what's being powered from that breaker, but my question is: is this automatically a Highly Bad Thing, or are there instances where two wires into one breaker is a legitimate installation? He wanted $450 to correct this, which given the triviality of snapping two breakers into a box and connecting a wire to each seemed to me to be a ripoff in the making, so I declined. He also suggested that since many of the breakers were quite old (it's a 1969 house, although some circuits have been added over the years), and since replacing them all would be expensive, that I have him "lubricate" the breakers. I had visions of duct-cleaning "services" in my head, and simply sent him on his merry way after paying the basic service fee. Was he blowing smoke, or did he know something about circuit breakers not apparent to me? Art |
#21
Posted to alt.home.repair
|
|||
|
|||
Is There An Electrician in the House?
Arthur Shapiro wrote:
I knew I had a problem yesterday morning when the furnace didn't come on at the usual 6:30 time where it progresses from the thermostat's nighttime setting into the waking time setting. Investigation revealed about half the house was without power, and half normal. I quickly ran extension cords to power the critical items (furnace, refrigerator, computer) to working outlets. Clearly one leg of the 120v supply was out. After cycling all the breakers, including the master, without success I decided it was time to pick an electrician out of the phone book, and the firm promised someone within an hour. While waiting outside for the electrician, a neighbor came out with exactly the same complaint. I knew then that it was a utility company problem, but having commited to the service call decided there was no harm other than a few $$$ in having the issue confirmed. (Turned out to be a burnt wire in an underground connection vault, and it took them until 10:30 in the evening to restore full power.) The gentleman was quickly able to confirm my hypothesis, but then pointed out some alleged issues in my breaker box. I personally choose not to fool with breaker boxes, other than tightening the screws on the blasted aluminum wire once every year or so; I'm comfortable with wiring and conduit manipulation and the like, but feel breaker boxes are left to pros. He pointed out one breaker which had two wires going into it. Being copper, I knew this was a circuit I had had (professionally) added in the past, but being on the nonfunctional leg neither he nor I could determine what was being powered from this breaker. He claimed that was highly dangerous. Now that I have power again, I'll be able to ascertain what's being powered from that breaker, but my question is: is this automatically a Highly Bad Thing, or are there instances where two wires into one breaker is a legitimate installation? He wanted $450 to correct this, which given the triviality of snapping two breakers into a box and connecting a wire to each seemed to me to be a ripoff in the making, so I declined. He also suggested that since many of the breakers were quite old (it's a 1969 house, although some circuits have been added over the years), and since replacing them all would be expensive, that I have him "lubricate" the breakers. I had visions of duct-cleaning "services" in my head, and simply sent him on his merry way after paying the basic service fee. Was he blowing smoke, or did he know something about circuit breakers not apparent to me? Art Having 2 wires on a single breaker is a code violation unless the breaker is rated for 2 wires - some SquardD ones are. It is not "highly dangerous" and is very easy to fix by pigtailing as about everyone has said. I have not heard of lubricating breakers. I very much doubt is possible to lubricate breakers. If it is possible, it is probably a bad idea. The whole thing smells like a scam. A good site for general information on aluminum wire is: http://www.inspect-ny.com/aluminum/ Much of the information is derived from the Consumer Product Safety Commission, which did a lot of work on aluminum wiring. IMHO the best link is: http://www.inspect-ny.com/aluminum/alreduce.htm This is a paper writen by an engineer who did extensive testing of aluminum connections for the CPSC, and includes many options for what to do with aluminum wiring. -- bud-- |
#22
Posted to alt.home.repair
|
|||
|
|||
Is There An Electrician in the House?
isnt pigtailing in the panel also a code violation? I thought you had to either put each home run or branch circuit on its on breaker OR have it made up in a J-box intead of taking to the panel and pigtailing Having 2 wires on a single breaker is a code violation unless the breaker is rated for 2 wires - some SquardD ones are. It is not "highly dangerous" and is very easy to fix by pigtailing as about everyone has said. I have not heard of lubricating breakers. I very much doubt is possible to lubricate breakers. If it is possible, it is probably a bad idea. The whole thing smells like a scam. |
#23
Posted to alt.home.repair
|
|||
|
|||
Is There An Electrician in the House?
In article , Tazz wrote:
isnt pigtailing in the panel also a code violation? No. I thought you had to either put each home run or branch circuit on its on breaker OR have it made up in a J-box intead of taking to the panel and pigtailing Lots of people think that -- but nobody's been able to show me where the Code says that... -- Regards, Doug Miller (alphageek at milmac dot com) It's time to throw all their damned tea in the harbor again. |
#24
Posted to alt.home.repair
|
|||
|
|||
Is There An Electrician in the House?
Doug Miller wrote:
In article , Tazz wrote: isnt pigtailing in the panel also a code violation? No. I thought you had to either put each home run or branch circuit on its on breaker OR have it made up in a J-box intead of taking to the panel and pigtailing Lots of people think that -- but nobody's been able to show me where the Code says that... -- Regards, Doug Miller (alphageek at milmac dot com) It's time to throw all their damned tea in the harbor again. Right, the panel is a listed enclosure where you can make splices. It's more of a best practices thing since the panel tends to get crowded anyway and having splices and pigtails in the panel just makes it that much messier. Pete C. |
#25
Posted to alt.home.repair
|
|||
|
|||
Is There An Electrician in the House?
Pete C. wrote:
Doug Miller wrote: In article , Tazz wrote: isnt pigtailing in the panel also a code violation? No. I thought you had to either put each home run or branch circuit on its on breaker OR have it made up in a J-box intead of taking to the panel and pigtailing Lots of people think that -- but nobody's been able to show me where the Code says that... -- Regards, Doug Miller (alphageek at milmac dot com) It's time to throw all their damned tea in the harbor again. Right, the panel is a listed enclosure where you can make splices. It's more of a best practices thing since the panel tends to get crowded anyway and having splices and pigtails in the panel just makes it that much messier. Pete C. I believe it is covered by NEC 312.8 - "Enclosures for switches or overcurrent devices". Splices are allowed if the fill at any cross-section is 75% or less. Wires running through the enclosure are allowed if the fill at any cross-section is 40% or less. An example would be if the panel ran out of breakers, existing breakers could be removed to add a breaker for a subpanel and the wires for the original breakers could be run through the panel to the new subpanel. -- bud-- |
#26
Posted to alt.home.repair
|
|||
|
|||
Is There An Electrician in the House?
|
#27
Posted to alt.home.repair
|
|||
|
|||
Is There An Electrician in the House?
Arthur Shapiro wrote: I knew I had a problem yesterday morning when the furnace didn't come on at the usual 6:30 time where it progresses from the thermostat's nighttime setting into the waking time setting. Investigation revealed about half the house was without power, and half normal. I quickly ran extension cords to power the critical items (furnace, refrigerator, computer) to working outlets. Clearly one leg of the 120v supply was out. After cycling all the breakers, including the master, without success I decided it was time to pick an electrician out of the phone book, and the firm promised someone within an hour. While waiting outside for the electrician, a neighbor came out with exactly the same complaint. I knew then that it was a utility company problem, but having commited to the service call decided there was no harm other than a few $$$ in having the issue confirmed. (Turned out to be a burnt wire in an underground connection vault, and it took them until 10:30 in the evening to restore full power.) The gentleman was quickly able to confirm my hypothesis, but then pointed out some alleged issues in my breaker box. I personally choose not to fool with breaker boxes, other than tightening the screws on the blasted aluminum wire once every year or so; I'm comfortable with wiring and conduit manipulation and the like, but feel breaker boxes are left to pros. He pointed out one breaker which had two wires going into it. Being copper, I knew this was a circuit I had had (professionally) added in the past, but being on the nonfunctional leg neither he nor I could determine what was being powered from this breaker. He claimed that was highly dangerous. Now that I have power again, I'll be able to ascertain what's being powered from that breaker, but my question is: is this automatically a Highly Bad Thing, or are there instances where two wires into one breaker is a legitimate installation? He wanted $450 to correct this, which given the triviality of snapping two breakers into a box and connecting a wire to each seemed to me to be a ripoff in the making, so I declined. He also suggested that since many of the breakers were quite old (it's a 1969 house, although some circuits have been added over the years), and since replacing them all would be expensive, that I have him "lubricate" the breakers. I had visions of duct-cleaning "services" in my head, and simply sent him on his merry way after paying the basic service fee. Was he blowing smoke, or did he know something about circuit breakers not apparent to me? Art The molded-case circuit breakers used for residential applications are _sealed_, one cannot lubricate them. The only thing that one can do is exercise them every 6 to 12 months or so, by turning them off and on several times. If any are binding, they should be replaced because they may not trip if/when called upon to perform under fault conditions. Large circuit breakers, such as is found in large commercial, industrial switchgear or utility substations are very complex mechanisms and do require periodic maintainance and lubrication by highly skilled factory approved people in a shop environment......_not_ by some electrician out in the field. |
#28
Posted to alt.home.repair
|
|||
|
|||
Is There An Electrician in the House?
|
Reply |
Thread Tools | Search this Thread |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Forum | |||
Electrician help please | Home Repair | |||
becoming an electrician | UK diy | |||
Finding a good electrician in Manchester to rewire a house | UK diy | |||
Illegally renting main house and living in another house built on back of the house on same plot... | Home Ownership | |||
Electrician | Home Ownership |