Is there any way to speed up the time it takes to get the warm water to
run out of the faucet? It seems to take forever. I know it has to run
its course but I thought since it is 2005 maybe there is something new
out there that has handled this problem.

Thanks.

"Senin" wrote in message
oups.com...
Is there any way to speed up the time it takes to get the warm water to
run out of the faucet? It seems to take forever. I know it has to run
its course but I thought since it is 2005 maybe there is something new
out there that has handled this problem.

Thanks.


It takes longer if you're standing there waiting for it. Seriously. It does.

More seriously, if it really drives you crazy, havea plumber stop by and see
if it's possible to re-route the pipes and improve the situation. Or, just
leave it running slightly. No...wait....that's stupid.

I'll add something to your basket of worries. If it takes forever at the
kitchen sink, and you have a dishwasher, there's a good chance your
dishwasher doesn't get hot water for the first wash. If that concerns you,
run the sink water till it's hot, and THEN turn on your dishwasher.

Senin wrote:
Is there any way to speed up the time it takes to get the warm water
to run out of the faucet? It seems to take forever. I know it has
to run its course but I thought since it is 2005 maybe there is
something new out there that has handled this problem.

Thanks.

There are several possibilities. A loop may be best, but it means
running a new line back to the water heater. There is a pump that you start
right before you need your hot water and it pumps the water from the hot
line to the cold line so it fills the pipe quickly with hot water and
nothing pours out into the sink. Your plumber will know of both type
fixes. Neither is free.

--
Joseph Meehan

Dia duit

Check out the Grundfos Comfort System - Hot Water Recirculation System
at http://www.grundfos.com/web/homeus.nsf

I've installed it easily and it cured the same problem you describe.

Senin wrote:
Is there any way to speed up the time it takes to get the warm water
to
run out of the faucet? It seems to take forever. I know it has to
run
its course but I thought since it is 2005 maybe there is something
new
out there that has handled this problem.

Thanks.

Great. How much did it cost you to install and how much does it cost
you to run? Does the constant running of the pump cause wear on the
water heater?

Senin wrote:
Great. How much did it cost you to install and how much does it cost
you to run? Does the constant running of the pump cause wear on the
water heater?

The cost of installation will depend on your home. Running the return
line(s) will be the expensive part. However I would not expect it to be too
expensive.

The cost of running it should be not too high as well. It is just a low
volume pump. The wear on the water heater will be minimal at most.

The real cost will be the cost of heating water. You will now have two
long pipes (the supply and the return) constantly kept hot, except during
off hours if you use a timer. They will work cooling the water and putting
that heat into your home. During the heating season, the cost will be
minimal. However and this is something I did not see even remotely
referenced on the web site, during the cooling season, you will first pay to
heat that water which will warm your home, but you will also pay to remove
that heat with your air conditioner.

For me, I might be willing to accept the cost, assuming I was able to
insulate the pipes well to reduce the cost. My real objection is the total
lack of information about this on the web site, It makes me question all
the other information they provide.

--
Joseph Meehan

Dia duit

Senin wrote:
Great. How much did it cost you to install and how much does it cost
you to run? Does the constant running of the pump cause wear on the
water heater?

I did the installation my self so the cost was minimal. A return line
is not needed as the pump uses the cold water line for the return. So
all you need to do is install the pump to the hot water outlet on your
water tank. You'll also need to install a recirculating valve in a sink
far away from the hot water tank. If you have the flexible screw type
connection on the hot water tank then soldering is probably not
required.

The pump has a timer which can turn off the pump during the night etc.
The cost to run the pump is probably minimal. For me this was more of a
matter of comfort.

wrote:
Senin wrote:
Great. How much did it cost you to install and how much does it cost
you to run? Does the constant running of the pump cause wear on the
water heater?

I did the installation my self so the cost was minimal. A return line
is not needed as the pump uses the cold water line for the return.

Not to say that is a terrible idea, but you should remember that using
the cold water as a return line will mean you are likely to get warm to hot
water from the cold water side until you let it run a while.

So
all you need to do is install the pump to the hot water outlet on your
water tank. You'll also need to install a recirculating valve in a
sink far away from the hot water tank. If you have the flexible screw
type connection on the hot water tank then soldering is probably not
required.

The pump has a timer which can turn off the pump during the night etc.
The cost to run the pump is probably minimal. For me this was more of
a matter of comfort.

--
Joseph Meehan

Dia duit