Home Repair (alt.home.repair) For all homeowners and DIYers with many experienced tradesmen. Solve your toughest home fix-it problems.

Reply
 
LinkBack Thread Tools Search this Thread Display Modes
  #1   Report Post  
Pawel
 
Posts: n/a
Default how to choose a new oil burning furnace

I am looking for a help in picking a new oil burning furnace (with AC coil).
Co far i got two estimates 4600 for williamson installed by my local oil
company (Santa Oil) and 5600 for Kenmore installed by Sears. I wonder if
there are any sites comparing furnaces and if anyone has experience with
Sears and their oil furnaces. thanks


  #2   Report Post  
Dr. Hardcrab
 
Posts: n/a
Default


"Pawel" wrote in message
...
I am looking for a help in picking a new oil burning furnace (with AC
coil). Co far i got two estimates 4600 for williamson installed by my local
oil company (Santa Oil) and 5600 for Kenmore installed by Sears. I wonder
if there are any sites comparing furnaces and if anyone has experience with
Sears and their oil furnaces. thanks


Your local oil company will probably have the best prices and service. Not
bad-mouthing Sears, but all they are is a middle man. They get one of the
local contractors to do the work for them so you end up paying more just to
have "Sears" on your furnace (and the furnace is NOT made by Sears).

Get at least 3 QUOTES (not estimates) from at least 3 different companies.
The brand doesn't mean as much as the installer.

Armstrong furnaces are inexpensive (compared to others) and very dependable.
ThermoPride is a very good furnace, but you are going to pay big bucks for
it.


  #3   Report Post  
Steve@carolinabreezehvac
 
Posts: n/a
Default


"Pawel" wrote in message
...
I am looking for a help in picking a new oil burning furnace (with AC

coil).
Co far i got two estimates 4600 for williamson installed by my local oil
company (Santa Oil) and 5600 for Kenmore installed by Sears. I wonder if
there are any sites comparing furnaces and if anyone has experience with
Sears and their oil furnaces. thanks



Depending on where you are at, (area you live in) and the actual location of
the furnace in your home, and any modifications that are needed to install
the new unit in place of the old, the size of the furnace in BTUs, and the
style of unit... that price is either dead on, or....holy ****..you got
suckered.

First and foremost, Sears is one to stay away from. Period. Right now they
are in a world of crap in some areas for using non licenced persons.
The Kenmore unit isnt made by Kenmore, and for that price, I can about
install you two Thermoprides.

Comparing the units....thats about pointless. One is no better than the
other. The difference is in the installation. Its ALL total garbage in the
box, its up to the installer to insure that it is installed in a manner that
will relate to no problems due to the installation, and then, after its
installed, its set up correctly. There is more to installation of an oil or
gas unit than ripping the old one out and slapping in a new one, and oil has
its own issues.

I sell two brands of oil units. York and ThermoPride. ThermoPride has a
factory right down the road, and its close to get parts should they be
needed, but todays oil units are all about the same. The difference is in
the heat exchangers and ThermoPride uses a copper sprayed exchanger.
Personally, I have owned a ThermoPride oil unit, and can see NO difference
in performace over any other brand.
I also replace more ThermoPride units due to rust than any other unit. That
could be due to the fact that everyone sells them here, and they last a good
long while, or it could be that the finish isnt very consumer friendly.
That said, its your money. The thing that you want to know is who is pulling
the permits, and are they insured and licenced. Then, if you trust what they
say, go with the brand they sell. Insure that you get the unit properly set
up after its installed, and that means a smoke test, and a heat rise check.
Also, with todays units being a bit more efficient, you will want the
installer to for SURE run a manual J on your home, or you might not save a
bit of money if all he does is goes under and looks at the unit and says,
Yup..its got 120,000 BTUs your getting 120,000BTUs to replace it...that
might NOT be what is needed. You have no way of knowing if the original unit
is sized correctly, or what the current rating is on it.
If you go to the same size unit, with a higher AFUE rating, then you are
automatically OVERsized.

Experence with Sears? They make the legitimate smaller installers and
companies lots of money.


Reply
Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules

Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
Help. Furnace improperly installed? Chuck Home Repair 11 November 2nd 04 02:26 AM
Clueless Inspector Faults Furnace Install Hell Toupee Home Repair 3 October 8th 04 06:47 PM
Furnace problems - repair, replace or ???? Paul Home Repair 11 March 24th 04 12:59 AM
Oil furnace burning 'rich mixture' Michael Walsh UK diy 4 February 26th 04 10:10 PM
Furnace Problem...HELP! torque Home Repair 5 January 6th 04 01:24 AM


All times are GMT +1. The time now is 09:18 PM.

Powered by vBulletin® Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004-2024 DIYbanter.
The comments are property of their posters.
 

About Us

"It's about DIY & home improvement"