Home |
Search |
Today's Posts |
|
Electronics Repair (sci.electronics.repair) Discussion of repairing electronic equipment. Topics include requests for assistance, where to obtain servicing information and parts, techniques for diagnosis and repair, and annecdotes about success, failures and problems. |
Reply |
|
LinkBack | Thread Tools | Display Modes |
#1
|
|||
|
|||
Hitachi C43WP910 rear projection TV
Hi, Anyone familiar with these?
PSU seems ok, it fires into standby. when you bring it out of standby it strikes up with a slight rustle of EHT and 6/7 green LEDs come on (secondary voltage indicators I presume). after approx 1second it then 'trips' back to standby and the LEDs each fase away over 1-2 secs. It repeats this 3 times before 'locking' into standby. Theres no sound of arcing and none of the usual comps seem faulty. LOPTx ? Is this the most likely suspect, or are there other common faults with these monsters (well in the UK 43" is considered big still!) AW |
#2
|
|||
|
|||
Look carefully at board; do ALL the LED's light? If so, when set shuts down,
does one of the LED's go out faster than the others? One acting different is key to missing voltage. Hitachi has service manuals online free after registering online with them. |
#3
|
|||
|
|||
Thanks for help.
of the 5 green leds, DP15 goes out the quickest, but not 'instantly' as I would expect if the rail was short. DP06 a re led with PROTECT LED against it comes on when the set strikes up out of standby, going off quickly when it trips. I don't know what this signifies except it is in the SMPSU area and perhaps should only illuminate when theres a fault? which there is!! I've looked at the Hitachi eu service website the manual is there, but as you said an account/pwd is required. I've rung to try to get one but I suspect they aren't going to let non account holders have access. manaul is the CL43WP910TAN Anyone out there with access would care to download and pass it on? to: service at wilkinsons dot tv I would be very grateful Andrew "BWL" wrote in message ... Look carefully at board; do ALL the LED's light? If so, when set shuts down, does one of the LED's go out faster than the others? One acting different is key to missing voltage. Hitachi has service manuals online free after registering online with them. |
#4
|
|||
|
|||
You're definitely going to need the manual; Hitachi's typically use as many as
two dozen diodes to route over/under voltage, loss of sweep/deflection, over current and x-ray detect signals to the shutdown circuits. You will also need a peak-hold meter to determine where the shutdown signal is coming from. Expect this to take a while... |
#5
|
|||
|
|||
You're definitely going to need the manual; Hitachi's typically use as many as
two dozen diodes to route over/under voltage, loss of sweep/deflection, over current and x-ray detect signals to the shutdown circuits. You will also need a peak-hold meter to determine where the shutdown signal is coming from. Expect this to take a while... |
#6
|
|||
|
|||
Thanks for the help. I've tracked down a copy of the manual. Hope to have it
soon. If its a board fault that doesn't worry me too much. I was more worried by the thoughts of problems with the CRT's etc. since this 3CRT technology is unfamiliar to me Andrew "BWL" wrote in message ... You're definitely going to need the manual; Hitachi's typically use as many as two dozen diodes to route over/under voltage, loss of sweep/deflection, over current and x-ray detect signals to the shutdown circuits. You will also need a peak-hold meter to determine where the shutdown signal is coming from. Expect this to take a while... |
#7
|
|||
|
|||
Thanks for the help. I've tracked down a copy of the manual. Hope to have it
soon. If its a board fault that doesn't worry me too much. I was more worried by the thoughts of problems with the CRT's etc. since this 3CRT technology is unfamiliar to me Andrew "BWL" wrote in message ... You're definitely going to need the manual; Hitachi's typically use as many as two dozen diodes to route over/under voltage, loss of sweep/deflection, over current and x-ray detect signals to the shutdown circuits. You will also need a peak-hold meter to determine where the shutdown signal is coming from. Expect this to take a while... |
Reply |
Thread Tools | Search this Thread |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Forum | |||
ICs for Sale - Specials, obsolete and Memory | Electronics Repair | |||
ICs for Sale - Specials, obsolete and Memory | Electronics Repair | |||
Hitachi Rear Projection Color Alignment | Electronics Repair | |||
Hitachi Projection Tube Part Description Confusion | Electronics Repair | |||
Hitachi Rear Projection TV Power Issue | Electronics Repair |