Hallo!
The primary of the trasformer of my CD-Player Pioneer PD-5700 is open. (In
Italy the voltage is 220 V).
The transformer has another input. It is not open. Should it be for 110 V?
Could I buy a 220 to 110 V trasformer and so use the 110 V transformer
input?
Thank you!
Gaspar - Italy

"Gaspar" wrote in message
. ..
Hallo!
The primary of the trasformer of my CD-Player Pioneer PD-5700 is open. (In
Italy the voltage is 220 V).
The transformer has another input. It is not open. Should it be for 110 V?
Could I buy a 220 to 110 V trasformer and so use the 110 V transformer
input?
Thank you!
Gaspar - Italy


If you take some other transformer giving some "safe" voltage and disconnect
all the leads from the transformer you are about to measure you can check
the ratio's between the different coils.

So - let's assume that you have transformer that produces 6V AC (note AC --
DC won't do).

If you take the assumed input and check the voltages on the "outputs" you
should see really low voltages.
You can now swap the 6V to the point where you saw the highest voltage.

Now you can measure the voltages between the different coil-ends. The "turn
ratios" are relative to the voltages and vice versa if there is no power
being drawn from the transformer.
Then you must know or find out what is the input voltage of your player and
then see if you got that to appropriate output what would be in the input.
Also it can be helpful to try to look the transformer with any markings of
the voltages - usually there is none but sometimes the transformers get
labelled on assembly with max ratings (voltage and amperage).

This of course will not give you 100% certain answer but at least will rule
out a possibility of totally blowing your device in case the two coils were
ment to be put in series in case of 110V.

Good luck

// Marko

You should fix it properly, especially for safety and reliability reasons. I
wouldn't want to be using a device with a known issue in the power
transformer, no matter what it is.



--

Greetings,

Jerry Greenberg GLG Technologies GLG
=========================================
WebPage http://www.zoom-one.com
Electronics http://www.zoom-one.com/electron.htm
=========================================


"Gaspar" wrote in message
. ..
Hallo!
The primary of the trasformer of my CD-Player Pioneer PD-5700 is open. (In
Italy the voltage is 220 V).
The transformer has another input. It is not open. Should it be for 110 V?
Could I buy a 220 to 110 V trasformer and so use the 110 V transformer
input?
Thank you!
Gaspar - Italy

"Gaspar" wrote in message
. ..
Hallo!
The primary of the trasformer of my CD-Player Pioneer PD-5700 is open. (In
Italy the voltage is 220 V).
The transformer has another input. It is not open. Should it be for 110 V?
Could I buy a 220 to 110 V trasformer and so use the 110 V transformer
input?
Thank you!
Gaspar - Italy





It should work just fine, just make sure you disconnect the open transformer
winding.

There is a chance you have an open thermal link on the primary side. Very
common on equipment sold in the U.S. I suppose your 220V model could use one
as well. It can be jumpered if accessible, but this presumes you know what
you're doing, otherwise _bad_ things can happen.

Mark Z.

--
Please reply only to Group. I regret this is necessary. Viruses and spam
have rendered my regular e-mail address useless.


"Gaspar" wrote in message
. ..
Hallo!
The primary of the trasformer of my CD-Player Pioneer PD-5700 is open. (In
Italy the voltage is 220 V).
The transformer has another input. It is not open. Should it be for 110 V?
Could I buy a 220 to 110 V trasformer and so use the 110 V transformer
input?
Thank you!
Gaspar - Italy

"Mark D. Zacharias" wrote in message
...
There is a chance you have an open thermal link on the primary side. Very
common on equipment sold in the U.S. I suppose your 220V model could use
one
as well. It can be jumpered if accessible, but this presumes you know what
you're doing, otherwise _bad_ things can happen.

Mark Z.


Don't jumper it, replace it.

There is no guidance for a correct replacement value, and one cannot
position the replacement inside the transformer. I generally use a link of
fuse-wire for the replacement. At 220v a 1/2 amp pico-fuse would probably be
adequate.

Mark Z.

--
Please reply only to Group. I regret this is necessary. Viruses and spam
have rendered my regular e-mail address useless.


"James Sweet" wrote in message
news:PwERb.133621$nt4.583457@attbi_s51...

"Mark D. Zacharias" wrote in message
...
There is a chance you have an open thermal link on the primary side.
Very
common on equipment sold in the U.S. I suppose your 220V model could use
one
as well. It can be jumpered if accessible, but this presumes you know
what
you're doing, otherwise _bad_ things can happen.

Mark Z.


Don't jumper it, replace it.